MAP Sensor Cleaning - Peugeot 206
Автокөліктер мен көлік құралдары
Removing and cleaning the MAP (manifold absolute pressure) sensor on a 2002 to 2009 Peugeot 206 1.1 litre petrol. Thanks for watching. Please comment, like and subscribe !.
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2021
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.
Пікірлер: 60
Thanks for watching my video. If you found this or any of my other videos helpful, maybe you could consider supporting my channel by using the ‘Thanks’ button below each of my videos. Your support would be really appreciated, thank you ! 👍 Screwsnutsandbolts
@patriotnederland6417
9 күн бұрын
The question how, KZread perfectly shownieuws. But the question when and why I still don't know. Can you explain when and why I have to do this? Thanks from me from the Netherlands. 👍
this kind of cleaning only shortens the life of the presure sensor.......good job
@screwsnutsandbolts
2 жыл бұрын
Thanks !
Thanks for another informative Video.May I wish you a Happy Christmas .Ive enjoyed all you've done this last year and look forward to the next for more useful hints and tips .M
@screwsnutsandbolts
2 жыл бұрын
Thank you very much, I appreciate that. Happy Christmas to you and yours too 🎅
Quite useful. Now I know what to look for with my hands, digging under the manifold on a 1.8 16v 406...
@screwsnutsandbolts
Жыл бұрын
Thanks for watching !
Great !!! Thanks man !!!👌
@screwsnutsandbolts
11 ай бұрын
You're welcome !
Very detailed video and very useful for me. Thank you! Since you disconnected the battery, I believe you could have cleaned the sensor connectors as well.
@screwsnutsandbolts
2 жыл бұрын
Thanks for watching :)
Thank you
@screwsnutsandbolts
Жыл бұрын
You're welcome
thanks
@screwsnutsandbolts
Жыл бұрын
You're welcome !
شكرا🇩🇿
@screwsnutsandbolts
Ай бұрын
Thanks for watching !
The breather hose and intake manifold are full of oil. Clean it too.
What kind of cleaner did you use??
Great video, thanks for share. I have a question: I need to replace the wiring plug (electrical harness) since the current is broke. The colors on the replacement wire plug (gray, yellow, black & orange) that I found do not have the same colors that the current (red, blue/green, blue/white & red/white) all this watching the wire plug connected into the MAP Sensor front view. Is there an specific way to find out the correct order to connect the wires or should I follow the order as they are positioned? I hope to explain my self correctly. Thanks.
@screwsnutsandbolts
7 ай бұрын
I would assume you should install them is the same order as they are positioned in the original wiring plug.
@jesusdavidroldan8256
7 ай бұрын
I was thinking the same but I want to ask you first. In case that this not work any idea of how I can match the wires?@@screwsnutsandbolts
Thanks for the video. Can you help me? I have the Citroen Xantia HDI 2.0, but I can't find where the MAP sensor is installed. Do you have any tips please? Thanks
@screwsnutsandbolts
6 ай бұрын
You're welcome. I haven't worked on one so I don't know, sorry.
Thank you man ,any solutions for improving the transmission oil cooling system for al4 gearbox ,gearbox start shifting very bad when engine tempreture get high, and i found in some websites that we can use an adapter for connecting an external coolant to prevent gearbox oil burn
@screwsnutsandbolts
Жыл бұрын
You're welcome. I don't have any experience with transmissions, sorry.
@maheraldokh6962
Жыл бұрын
@@screwsnutsandbolts thank you so much 🌹
top
👍
@screwsnutsandbolts
Жыл бұрын
Thanks !
I need your help sir. I have two connectors that have been cut off and I'm not sure which one to reconnect. Can I email you with the photo's, please? Thanks
How often should the MAP be cleaned ?
@screwsnutsandbolts
9 ай бұрын
There's no set time but I've heard people recommend every 30,000 miles
Saludos estimado tendra usted la medida del oring de este sensor?
@screwsnutsandbolts
Жыл бұрын
I don't know the size, sorry
Que sensor es el que está limpiando?
@timbresbermont651
Жыл бұрын
sensor map
why do u need to disconnect the battery , if u disconnect the MAP connector?
@screwsnutsandbolts
2 жыл бұрын
It's generally recommended that you disconnect the battery when working on any of the vehicle's electrical components.
@zsoltsiro1310
Жыл бұрын
in case the battery is faulty, its just a precaution
Pourquoi vous avez enlevé les tuyaux d'air
@screwsnutsandbolts
5 ай бұрын
To make more space when removing the sensor
I tried to undo bolt but it was rotten and snapped. Now I cant tighten sensor. Any solutions how to remove broken bolt, do I need to remove intake manifold?
@screwsnutsandbolts
2 жыл бұрын
You shouldn't have to remove the manifold. There should be plenty of videos on youtube showing how to remove a broken screw/bolt like this one: kzread.info/dash/bejne/hYGmpruDpryWhNY.html
@jovanmajstorovic41
2 жыл бұрын
@@screwsnutsandbolts Thanks for answer. Bolt is rotten by whole length and i tried to drill it and undo by flat screwdriver but it cant.
Wtf! You dont have to disconnect battery when replacing a sensor. Just be sure the car is off thats all. Its good to disconnect te battery if you had some fault codes, and if you want to reset all values so it can re-learn the new values from the new sensor.
what are the 'troubles' caused by a dirty air-flow sensor..??..thx...because I have micro engines cuts especially when accelerating harder (freeway)..i thought it could be a spark plugs big coil block who needs to be replaced along with new spark plugs..??
@screwsnutsandbolts
Жыл бұрын
There are a few issues that can be caused by a bad map sensor which could also be similar to other issues with the engine. A failing ignition coil pack or spark plugs could be causing the poor acceleration or even something as simple as a clogged fuel filter. Check this link: mechanicbase.com/engine/map-sensor-symptoms/
@hectorherbert6585
Жыл бұрын
@@screwsnutsandbolts thx for the tip..
@screwsnutsandbolts
Жыл бұрын
You're welcome !
Colocar subtitulo in spanish
Should clean the pipes you took off Too Because it's full of oil
A quoi sert ce capteur ?
@screwsnutsandbolts
Жыл бұрын
The MAP sensor provides instant intake manifold pressure information to the engine's electronic control unit. The data is used to calculate air density and determine the engine's air mass flow rate, which in turn determines the required fuel delivery for perfect combustion
Car alarm does not work Peugeot 206
دير شرح توضيحي أكثر او شرح تطبيقي
Аккум зачем отсоединять
@screwsnutsandbolts
Жыл бұрын
It's always recommended that you disconnect the battery when working on electrical components