#woodworking #finishing #4k Making an oil with different additives and trying it out. • A wavy oak box (4k build)
Жүктеу.....
Пікірлер: 19
@alexanderplaner796011 ай бұрын
The stain tests the oil to the extreme since it's highly penetrative even to the point of staining some plastics
@michaelmcdermott217811 ай бұрын
Excellent demonstration, thanks!
@MASI_forging11 ай бұрын
You do amazing work such a talent 👏👏
@christopherbarnes697611 ай бұрын
Thanks for sharing. I make a beeswax paste using the Lost Art Press recipe with orange oil. Love it. Will have to try your recipe.
@rawr2u1902 ай бұрын
I've always been curious about paste wax with resin. The Woodworker's Pocket Book from Lost Art Press mentions it, but doesn't say how much resin to add. I've heard carnauba wax can be a bit brittle. The brittleness can be reduced by mixing in polysorbate 60, not sure about ps 20 and ps 80 (according to Zhang et al DOI: 10.1016/j.polymer.2016.01.033) What are your thoughts on carnauba and carnauba mixed with beeswax? This was an interesting video, thank you. The results are pretty good for both of them.
@avramw5 ай бұрын
Thanks for showing this! Did you used boiled linseed oil or pure linseed oil?
@kswoodcraft60908 ай бұрын
thanks for sharing! what brand of urethane did you use?
@davidgriffith66274 күн бұрын
When you say “linseed oil” do you mean boiled linseed oil or just regular linseed oil?
@David_111116 ай бұрын
where did you buy the urethane ?
@davidrich12704 ай бұрын
Did you use off the shelf urethane ?
@dmanzo8116 ай бұрын
What are you spraying at the end to clean off the stain? Is that just water? Thank you for this video!
@alexanderplaner7960
6 ай бұрын
Yes it is just water.
@gary2475217 күн бұрын
Can you use tung oil rather than linseed oil?
@alexanderplaner7960
17 күн бұрын
Yes, I think it's might be even better than linseed oil
@davidearls2776 ай бұрын
I too am interested in your source for urethane
@alexanderplaner7960
6 ай бұрын
I used alkyd urethane varnish but polyurethane will work too, might be even better.
@karimchoufani9144
6 күн бұрын
Actually both are the same . Just marketing diversification
@susanp.collins78344 ай бұрын
Obviously not food safe...
@monkeysnark7043
2 ай бұрын
Misconception, as many over the counter finishes fully cured, becomes food safe. Fully cured means, wait till the carrier has fully evaporated and left behind only the solids, in form of wax, and/ or oils ( if the oils are pure, raw linseed, tung, mineral), and/or acrylics, which is approximately 30 days. With the caveat, you don’t want acrylic or varnish (hard) finishes for cutting boards, yet fine for wooden food containers, as well as table or counter tops. Cutting boards are coated with a mix of or combination of, only oils, raw linseed, mineral, or pure tung oil, with wax. You will probably need 3 to 4 coats, allowing to dry and buff in between each coat. Then top up every month or two depending on usage and wash technique. The weakest being mineral oil, as it doesn’t really dry. Most people are too lazy to put that many coats on, or have no idea. Shrugs. Cheers
Пікірлер: 19
The stain tests the oil to the extreme since it's highly penetrative even to the point of staining some plastics
Excellent demonstration, thanks!
You do amazing work such a talent 👏👏
Thanks for sharing. I make a beeswax paste using the Lost Art Press recipe with orange oil. Love it. Will have to try your recipe.
I've always been curious about paste wax with resin. The Woodworker's Pocket Book from Lost Art Press mentions it, but doesn't say how much resin to add. I've heard carnauba wax can be a bit brittle. The brittleness can be reduced by mixing in polysorbate 60, not sure about ps 20 and ps 80 (according to Zhang et al DOI: 10.1016/j.polymer.2016.01.033) What are your thoughts on carnauba and carnauba mixed with beeswax? This was an interesting video, thank you. The results are pretty good for both of them.
Thanks for showing this! Did you used boiled linseed oil or pure linseed oil?
thanks for sharing! what brand of urethane did you use?
When you say “linseed oil” do you mean boiled linseed oil or just regular linseed oil?
where did you buy the urethane ?
Did you use off the shelf urethane ?
What are you spraying at the end to clean off the stain? Is that just water? Thank you for this video!
@alexanderplaner7960
6 ай бұрын
Yes it is just water.
Can you use tung oil rather than linseed oil?
@alexanderplaner7960
17 күн бұрын
Yes, I think it's might be even better than linseed oil
I too am interested in your source for urethane
@alexanderplaner7960
6 ай бұрын
I used alkyd urethane varnish but polyurethane will work too, might be even better.
@karimchoufani9144
6 күн бұрын
Actually both are the same . Just marketing diversification
Obviously not food safe...
@monkeysnark7043
2 ай бұрын
Misconception, as many over the counter finishes fully cured, becomes food safe. Fully cured means, wait till the carrier has fully evaporated and left behind only the solids, in form of wax, and/ or oils ( if the oils are pure, raw linseed, tung, mineral), and/or acrylics, which is approximately 30 days. With the caveat, you don’t want acrylic or varnish (hard) finishes for cutting boards, yet fine for wooden food containers, as well as table or counter tops. Cutting boards are coated with a mix of or combination of, only oils, raw linseed, mineral, or pure tung oil, with wax. You will probably need 3 to 4 coats, allowing to dry and buff in between each coat. Then top up every month or two depending on usage and wash technique. The weakest being mineral oil, as it doesn’t really dry. Most people are too lazy to put that many coats on, or have no idea. Shrugs. Cheers