As a beekeeper and woodworker, I put my cappings and such in an old tube sock then place it in the water. The wax that comes out of the sock is almost clean. The added bonus is the chopped up sock makes a good fire starter.

@cotteeskid

Жыл бұрын

that's a great idea. I was using sections old cotton sheets over a strainer but inefficient as heat isn't maintained as you pour it. But your method, the wax is under constant heat.

@Michaelsmercedes

14 күн бұрын

Waterproof socks!

If you want to filter raw dirty wax in ONE GO, here's what we do with our wax (we keep bees): 1. Find a metal pot or tray that fits into your oven 2. It needs to be deep enough to hold some water in it and hold some kind of a metal strainer - it doesn't matter if it's fine or not 3. Put a few inches of water into the pot, put the strainer on it, put 2 layers of kitchen towels across the whole strainer and put the wax onto that 4. Put everything into the oven and set it to 155-160F (65-70C) and check periodically if there's any wax left in the strainer. 5. When all the raw wax is gone, turn off the oven and let everything cool down The wax slowly melts and runs through the towels, dripping into the water below. All the impurities and stuff are left on the towels in the strainer. When you let everything cool, the wax in the water solidifes into a puck and floats on top of the water, but it's clean, all that dirt and stuff is on the towels. You just throw it away and voila, a pot full of nice clean wax. The 155-160F temperature is the melting point of beeswax, when it flows nicely, cause it needs to get thin in order to go through the towels. Beeswax is flammable and it does not boil, just gets hotter and hotter and then ignites, but don't worry - the flashpoint of beeswax is 400F (204C), so you're nowhere near that. Also, the 155-160F range won't damage or discolor the wax, it won't ruin it. When I first tried this, I wasn't expecting results, really, I thought I was going to get a bunch of hardener wax towel mess, so it was pretty much a surprise when it worked. I've been using this method every since cause it removed any neccessity for cheese cloths, rags, multiple meltings and a bunch of water I used to use, and - it comes out yellow and clean. Hope this helps, thanks James for making this video!

@WoodByWrightHowTo

3 жыл бұрын

Well that is an interesting idea! I will have to give that a try next time.

@cotteeskid

Жыл бұрын

I tried this method a while back, but maybe I had slightly higher temperature as my wax was duller in colour and not as bright yellow when I have done it with water. Will have to try again to see, although I'm thinking of using a solar melter as well to see how that goes.

@Obscurity202

9 ай бұрын

Can you clean the towels after or are they rekt?

@samuelmellars7855

7 ай бұрын

​@@Obscurity202I think by "kitchen towels", they mean the paper/tissue ones. So they are thrown out. Or become firelighters.

@Obscurity202

7 ай бұрын

ok thanks ! @@samuelmellars7855

Thanks so much for the "buy it if you want, make it if you want" approach. Totally the opposite of the "this is secretly an advert thinly disguised as a tutorial" approach. And with wax from a pal with bees and oil from a pal with a press, I never felt less advertised-to!

@Michaelsmercedes

14 күн бұрын

Then you should try bril-cream. A little dab will do ya. Now you have been advertised to

I am using your hard wax recipe for waxing my plane soles. I had an idea to pour it into a clean and empty twist up refillable deodorant container - should be less messy to handle :)

@nickgardner1705

2 жыл бұрын

Did this work? I'm very curious

@AssafOppenheimer

2 жыл бұрын

@@nickgardner1705 worked very well - a couple of things worth noting: 1) I used Jojoba oil instead of linseed (what I had on hand). 2) bees wax melts at around 70C or 160F. I recommend monitoring the temperature and pouring the wax at slightly above that. the first pour I did the wax was way to hot - it melted the plastic of the container and made a smelly mess. the second one I made sure the wax was much cooler (under 200F) and I pored it. works amazing. I was using my No. 8, then added some wax to the sole - it shot forward so fast I almost lost control :) also, keep a bowl of cold water with ice at hand

@nickgardner1705

2 жыл бұрын

@@AssafOppenheimer right on! Thanks for the tips :)

@adamthewoodworker2571

2 жыл бұрын

Damn I just saw your comment after I made the recipe in a tin jar. I should try it this way next time

@HomeImProveMentHow

Жыл бұрын

Excellent idea thanks for sharing that would work well

Found you suggested through a Reddit post! Digging up old content and happy to see you’re still selling these! Instant customer! Thank you!!!

Very nice tutorial video, thank you for taking time to film, edit and post this video. Liked and subscribed. I also ordered both of your waxes from your site.

Wow - the hard wax blend is incredibly useful. Game-changer thanks for sharing the ratio

@WoodByWrightHowTo

3 жыл бұрын

Thanks. My pleasure!

Thank you for sharing your wax mix recipe, really good stuff 👍

@WoodByWrightHowTo

3 жыл бұрын

My pleasure!

I just ordered one of each. Keep up the awesome work. Pleasure to support you and your channel.

@WoodByWrightHowTo

3 жыл бұрын

Much appreciated. I will keep them coming!

Great recipes! Another I like to use is a mix of roughly 3 parts beeswax to 1 part USP grade mineral oil. I adjust it until a sample of the cooled mix is like a thick grease or old Johnson's paste wax. At that point it can be easily massaged by hand into the wood. It's a great idea for food contact wood items like cutting boards, spoons, spatulas and salad bowls. And unlike the tung or other nut oils I used to use the beeswax and mineral oil is not a strong allergen in case someone in the family or a visitor is allergic to nuts. The mixture is surprisingly tolerant of being washed. But make at a dunk, wipe, rinse, dry sort of deal as any long term soaking will obviously soak into the wood after a while. So yeah. Beeswax. It's good for more than just in the shop.

Just ordered the soft wax, love that it is super natural product. Thanks!

@WoodByWrightHowTo

3 жыл бұрын

thanks man. I will get it in the mail in the morning!

Thanks for the good instructions, James! I ordered some pure bees wax and cold pressed linseed oil from a local health shop right away, will be making my own hard wax as soon as that order comes in!

@WoodByWrightHowTo

3 жыл бұрын

Sweet. Have fun. It's nice when you get your own mix down.

I love your instructional video:. It is simply wonderful to hear international traits coined into the narrative. Thank you so much for sharing this fabulous data. Best of luck.

Awesome James! I will be copying these into my shop recipes, when I feel like waxing poetic... ;)

Also works great on screws and drill bits, especially in hardwoods. And when I worked in the commercial glazing business (long, long time ago) we always used beeswax when cutting or drilling aluminum.

@WoodByWrightHowTo

3 жыл бұрын

So true.

@enricohernandez8356

2 жыл бұрын

I need to get two cans , but I can’t find the place to order

You could also put the cheese cloth underneath the Puck before you boil it.

@Jack-es9xq

3 ай бұрын

oooooooooh, that idea is a winner!

Was so excited when I woke up and realized it was Saturday and knowed that wood by wright had a video out!!!!

@WoodByWrightHowTo

3 жыл бұрын

Thanks man. I aim to please!

@Matthew-ir1ed

3 жыл бұрын

@@WoodByWrightHowTo hey james, great video, thank you for sharing. ive been using polymerized oil for years, but it isnt cheap stuff. i'm thinking about trying your slowcooker method to make my own. can you tell me if you separate the fats out of your flax oil before you put it in the slow cooker, or do you not bother with that step? also, how long do you cook it? on high or low?

Awesome video as usual. I think I’ll just keep buying from you to support the channel. My wife was listening and cracked up at the Brazilian wax joke. 😂😂😂😂😂😂

@WoodByWrightHowTo

3 жыл бұрын

LOL thanks man! you know yuo have a good woman when she is willing to laugh at that joke.

That's awesome, James. I've been looking for a paste wax recipie to start from. Thanks

@WoodByWrightHowTo

3 жыл бұрын

Have fun man.

@thomasarussellsr

3 жыл бұрын

@@WoodByWrightHowTo thanks.

This is exactly what I needed! Some time ago, I got 2 blocks of bee’s wax for lubricating my planes and that does not work at all because the wax is way too hard. As is so often the case, I thought this was a good idea at the time. Oh, well. We’re traveling right now, but first thing I’m gonna try when I get home is to make the hard wax according to this recipe! Looking forward to it!

@hydrochloridrix

Жыл бұрын

I did this yesterday. Took like 10 minutes for the wax to dissolve or melt, plus another 1-2 hours for it to cool down again after the pour. OMG, this stuff is sooo good and so so much better than the obvious crap I used to use. Thank you so much!

Pretty interesting, James!!! Thanks for all the tips! 😃 Stay safe there with your family! 🖖😊

Wow I just went and checked out the prices and your cheaper than store bought wax. Next time I need some you will have my order I can promise that!! Keep up the awesome work James!

@WoodByWrightHowTo

3 жыл бұрын

Thanks. I try to keep it affordable whenever possible.

Ah, i had the old video before. THIS one is my go-to-video on waxes. Now to actually make the softwax. 😅

Ordered one of each. I Enjoy your videos.

@WoodByWrightHowTo

3 жыл бұрын

thanks Greg that means a lot!

I was literally about to say "you didn't do 'wax on, wax off'!, but you beat me to it! But you one upped that by starting a new channel!

@WoodByWrightHowTo

3 жыл бұрын

Lol there were too many good wax jokes I had to call it back on this one.

Great video. Ive been making my own for a while now as well. Just like you said, i found a formula that works best for me 👍

@Kashif121472

Жыл бұрын

please share

I use bees wax with pine turpentine and works very well. Also it depends from the postions of these two elmements to be hard or very soft. I will try also your recipe. Thanks for the video and ideas

Very cool. Thanks for sharing.

@WoodByWrightHowTo

3 жыл бұрын

my pleasure

Good tips thanks!

Mmmmm... bits of bees I love your cooking episodes

@ricos1497

3 жыл бұрын

Also, would a lipstick holder be a good container for this sort of thing, or would a roll on deodorant holder be a better size? If I can get hold of some local apiaiaiaiaiairists, I'd like to experiment.

@WoodByWrightHowTo

3 жыл бұрын

I have tried finding a canister like that but have not found one economical enough yet. i know Rob Cosman uses a glue stick canister. If I were to do them one off I could use old ones.

@ricos1497

3 жыл бұрын

@@WoodByWrightHowTo are you thinking what I'm thinking? We could break into Rob Cosman's shop....

Came to learn about wax, learned the word Apiary.

@WoodByWrightHowTo

3 жыл бұрын

that is a good one

@avisato9950

3 жыл бұрын

i believe that means new england bees only like their wax to finish furniture in the ape cod style... *smhams*

First time I tried this the worst part was cleaning the pot. Second time I tried I boiled water and put the wax in one of those metal pie pans and set it on top of the boiling water pot. Worked great and clean up was easy peasy.

@WoodByWrightHowTo

3 жыл бұрын

right on. that is why I have dedicated pots for it.

👍😎🤣Great Job!!! Very Cool!!! Thank You Sir For Sharing!!!

Sadly my workshop is outside and pretty much all tools are staying outside. I made some with beewax pellets and vegetable oil. Isn't perfect but will prevent a lot of rusting especially for my chisels.

thanks for sharing that

Just an idea, have you thought about using a cheese slicer to clean the entire top one time? You could make a large enough one to clean it in one swoop. I made one for cutting clay. :)

I of course made a mess in the kitchen. Thankfully my wife and I don't share a kitchen. We'll see how it goes. I made the harder version,and made it into this wafers, because that's what I had. Summers here are upper 90s and low 100s daily, so I might have to melt it into a bigger chunk. Vamos a ver. Thanks for the instructions. I'll do better next time.

nice video

Pretty slick! "Planely"

@WoodByWrightHowTo

3 жыл бұрын

LOL thanks man!

Thanks, I’m going to order some of your 2:1 hard wax with raw linseed oil, looks useful, and plain beeswax is way too hard. FYI, I made my own soft wax following an old “colonial” recipe I found online, and it is basically 1:1:1, (or in your example 2:2:2) with beeswax, BLO, and mineral spirits in equal parts. I’m not sure what the extra half measure of mineral spirits does to the hardness compared to your recipe, whether it makes it harder or softer (?) but it seems to work ok on my wood projects. Thanks. 👍

Thank you James. A needed topic. A note, linseed oils of store bought types. Boiled Linseed Oil is not boiled, but treated with a chemical, thereby it's not to be confused with the real thing, yours. Where in Hawaii could I find pure Linseed oil is anyone's guess.

@woodworkerroyer8497

3 жыл бұрын

I wonder if you could get raw oil there. I know they had both "boiled" and raw in Tonga, but they definitely don't have the same laws as the US does though. And I think the name stuck around from when it USED to be boiled. And now they just call it boiled when they put a chemical in it to do the same job. Much like the British call flashlights "torches," even though the ONLY similarly is that they both produce light.

I made few ratios: - only candle - very hard to apply to the sole and can't feel glide differences . - 1:4, 1part liquid paraffin with 4 parts melted candle - the mixture stays hard like candle and feels little bit oily. Better apply to the sole than the pure candle, but still not good gliding. - 1:3 - the mixture stays hard and feels more oily in the hand. Good apply to the sole, little bit better gliding. - 1:2 - the mixture stays hard again and feel very oily in the hand. Very good apply to the sole, very good gliding. - 1:1 - the mixture stays hard at first look, feel very very oily and feels like starts to melt in the hand. Apply to sole very easy and glide like 1:2 mixture. 1:2 think is the best mix for me. Twist cans from paper glue were filled, so the wax will stay clean and easy to use. I'm pretty sure Rob Cosman's wax is on the same base. Not so much variants for wax i think. The bees wax i will use for wood protection, just doesn't work for me as lubricant. Happy planing guys! :)

I think you have answered a question I have had since the early 80’s. In high school woodworking, we used a soft wax that smelt like turpentine and looked like bees wax. I do believe it was essentially like your soft wax. I’m tempted to make my own now, but am more likely to buy yours, if it can be shipped international, and our Border Control doesn’t consider it a biohazard (Australia)

@WoodByWrightHowTo

Жыл бұрын

I have shipped to down under before, but the shipping price is almost twice the price of the product. if not more.

@gaijininja

Жыл бұрын

@@WoodByWrightHowTo But if it's a good product that lasts years, it's worth it.

Have you tried adding a bit of carnauba wax to the mix to achieve a harder wax?? Love your videos

@WoodByWrightHowTo

3 жыл бұрын

oh ya. you can mix in most any wax. I have a friend that uses industrial hard waxes that harden to be incredibly tough.

I've just received some Bees wax that I ordered from a local bee keeper to make some polish up - I will be following your recipe. (Seeing as I'm over in England I figured the shipping cost of buying yours would be prohibitive!).

@WoodByWrightHowTo

2 жыл бұрын

Sounds like fun. Yes. Shipping a can of wax over there would cost more than the wax itself. But I have done it a few times lol

@WingingItBoatingonaBudget

2 жыл бұрын

@@WoodByWrightHowTo I will be trying it using a old cast iron 'glue pot' that I have restored using electrolysis, and that will be on top of our log burner, so I will need to keep a close eye on temperatures. If all else fails I will have to stump up the money and order some from you!

The mineral spirits, That's what gives you the soft wax,,

Hello how are you doing great video like always how can you dark in the oil wax for different colors ok thanks have a great day take care

@WoodByWrightHowTo

3 жыл бұрын

You can add wood dye for oil-based stains.

hi . nice video. i used parrafin wax ( candles) and coconut oil to make a hard paste wax in a 2:1 ration like you instructed , but the resulting paste wax came out crumbly ( when i tried to apply it ) . should i increase the ratio of parrafin wax to the oil and repeat ?Thanks

@WoodByWrightHowTo

2 жыл бұрын

coconut oil is an odd one as it is most often solid at room temperature a it tends to make the was brittle. Increasing the wax will help.

bit late after the making of the video, but I made my own hardwax with linseed oil & beeswax (would have bought yours, but shipping it to Europe seems a bit over the top), but when I put it on my tools, it sort of seems to attract dust and stuff. Am I putting it on too thick (or not rubbing it out enough) or did I do something wrong in making it?

Greetings. Awesome video. Was wondering if rags used for the soft wax could be prone to self-combusting because of the boiled linseed oil, or is it stabilized because of the beeswax and mineral spirits?

@WoodByWrightHowTo

3 жыл бұрын

there would be a little chance of it but only very slightly. Contrary to popular belief oil soaked rags will only combust under very specific situations. But unfortunately that is wadded up in the bottom of a trash can.

Could you add a few coats of shellac after the finishing wax, or would the wax prevent the shellac from adhering?

@WoodByWrightHowTo

2 жыл бұрын

The wax should go on after the shellac. Wax isn't really a finish by itself. It fills the pores on top of wax and smooth out the finish.

Is the ratio of wax to linseed oil measured by weight or by volume? Excellent video by the way! I'm always impressed when people show step-by-step videos on how to make the same product that they also sell.

@WoodByWrightHowTo

Жыл бұрын

I go by eye. But originally by weight. The nice thing is it not an exact science. You get kinda close and it will be perfect.

This wax looks so good! I would love a dark antiquing wax too.....do you know if a colourant can be added to your recipe?

@WoodByWrightHowTo

2 жыл бұрын

Sure. I have seen several people add dyes and stains to it.

@g.m.5412

2 жыл бұрын

@@WoodByWrightHowTo cool thanks!

I find the cookware almost impossible to clean after cooking paste wax, what do you do to get rid of cold wax residue? Also I have seen rust in a few wax containers when they are metallic, how do you avoid that? Thanks in advance! p.s. I now use a non siccative oil after having unused soft wax that went too dry.

@WoodByWrightHowTo

3 жыл бұрын

I have dedicated pots for it. You can get old crock pots at the resale store for a couple bucks and never have to clean them. I have never had rust in any of my cans before. Not sure what would cause that as it is usually used as a rust preventor. Sounds like the mix is too base. That might cause it.

If you crush the puck before heating it up for the secont time you"ll use less energy and time to melt it again. If you manage to doubble the surfvavae area it will melt in half the time so I imagine only 4 good centre brakes should do it.

Great video! One question: Why do you use raw linseed oil for the hard wax and the boiled for the soft wax? I assume there is a reason since you mentioned that you go through the trouble of boiling it yourself. Is it that the boiled penetrates wood better?

@WoodByWrightHowTo

2 жыл бұрын

The hard wax I use for two lubrication and rust prevention. In that case I would rather the oil stay liquid and softer longer. The boiled linseed oil will polymerize in a day or two. And that's what you want on wood finishes. So that's what I use in the soft wax that gets used for finishing projects.

Those tins look really handy! Do you mind sharing where you got them?

@WoodByWrightHowTo

3 жыл бұрын

I ordered them through Uline. They have them in all sorts of sizes and colors.

Try a paint scraper to remove the gunk from the puck

Would I be able to substitute paraffin for the beeswax? I have a few slabs of gulf paraffin, boiled linseed & mineral spirits. Would this work or would the end product be to hard to buff as a paste wax?

@WoodByWrightHowTo

Жыл бұрын

It works well. You'll get a slightly harder wax. So if you want it to be softer you'll probably need to mix in a little bit more oil.

If you only have regular BLO, do you still need mineral spirits for the soft wax?

@WoodByWrightHowTo

3 жыл бұрын

If you want it send out so that you can smear it onto the surface the mineral spirits will allow you to do that. Without the mineral spirits it is much harder and you generally have to keep it up to get it to work into the wood.

Thanks for all the tips! I made 4 -4oz cans. and 2 of them had a white crystallizing look when it cured. Any ideas what i did wrong? Thanks from MN

@WoodByWrightHowTo

2 жыл бұрын

Not sure. Feel free to email me some pictures.

@tomleonard1589

2 жыл бұрын

@@WoodByWrightHowTo Thanks, I dont see an email to send a few pictures. I'm guessing its private.

Hi James sir wich of you homemade wax's are the food safe ones the soft or hard plz

@WoodByWrightHowTo

Жыл бұрын

That all depends on your definition of food safe. The hard wax is just beeswax and raw Lindsay oil. Most people would consider that to be food safe. The soft wax is homemade boiled linseed oil, beeswax, and mineral spirits. For my uses I consider that to be food safe. But some people will not like the use of mineral spirits.

Thank you for the very informative video! I'm planning on making my own soft wax as a varnish for gouache/acrylic paintings but I just have a question. What exactly does the mineral spirits do for the mixture? Thanks in advance :)

@WoodByWrightHowTo

3 жыл бұрын

That thins it out so it can spread, then it evaporates.

@foxtarel

3 жыл бұрын

@@WoodByWrightHowTo Thank you!

@foxtarel

3 жыл бұрын

@@WoodByWrightHowTo Sorry I have another question ;; Can I use any other type of oil like maybe fractionated coconut oil? Have you tried it with different oils before?

@gorancho1

2 жыл бұрын

How come mineral spirits dont evaporate when you add them to warm mix of wax and oil , and during storage? There will be no white spirit in that mix after lets say 1 month, so i dont see what is use of adding it? I thought soft wax is soft bcs of half of it is oil ?

Use soft wax for table saw top? I use Johnston's past wax.

@WoodByWrightHowTo

3 жыл бұрын

that is good stuff for it.

Thank you for this. Do you let it cool at room temperature or put the oil-wax mix in the refrigerator?

@WoodByWrightHowTo

3 жыл бұрын

depends on how rushed I am. most of the time I just air cool it, but if I need to get another batch out i put it in the fridge.

@lishaieitan799

3 жыл бұрын

Thanks :) Also, would products finished with the soft wax be food/toddler safe when it hardens (and, presumably, the mineral spirits evaporated)? Or would you substitute the mineral spirits with something else for that purpose? Really like your channel, and just made the hard paste wax :)

That was a very informative video. You don’t have any concerns with handling mineral spirits without gloves? Am I misinformed about this chemical?

@WoodByWrightHowTo

5 ай бұрын

I don't go dipping my hands in it but splashing here and there isn't going to cause a problem.

Hey James any downside to using tea light candle wax? Got a huge bag of these suckers and would like to put them to good use. Also what about using a store bought BLO? Trying to make a hard wax for planing and sawing

@WoodByWrightHowTo

3 жыл бұрын

Super. It is parifin wax works great. Store bought works fine but I would not apply it with bare hands.

@rosstifer07

3 жыл бұрын

Wood By Wright How 2 thanks James!! Planning on filling some chapstick tubes with it so no worries about hand contact.

Is the hard wax (the 2:1 ratio) good for waterproofing canvas (like otterwax)?

@WoodByWrightHowTo

Жыл бұрын

that is probably about the mix I would use. it would take a bit to rub that in but with a little heat that would do quite well.

Hi James do you sell the finish that's in like oil form for like dipping projects in sir

@WoodByWrightHowTo

Жыл бұрын

The wax comes in a small tin.

Could you replace the mineral spirits with orange solvent in the soft paste wax recipe to make it "food safe" (ie for toys possibly boards) I would you make one from a raw linseed oil? I plan on making my own boiled linseed oil, is tung oil a valid option? Thanks

@WoodByWrightHowTo

Жыл бұрын

Yes and yes. you can make it any way you like. raw linseed oil works fine too it just takes longer to fully polymerize.

Hi so I watched this. Do you think the tried and true danish oil old work here? The company told me that they use a different kind of linseed oil in their original finish which is basically a thin paste wax?

@WoodByWrightHowTo

3 жыл бұрын

Yes their Danish oil is actually BLO. it is one thing I hate is the name is misleading.

Hello, what are white spirits?

Hopefully you will reply on an old video. Will store bought Boiled Linseed oil work for this recipe? Love all your videos and they are helping me build my workshop!

@WoodByWrightHowTo

Жыл бұрын

Sure. I would just not use it in any food tool applications

👌👌👌

Hello, can i put some kind of charcoal or something like that to add a darker color on my paste wax?

@WoodByWrightHowTo

2 ай бұрын

Sure. People used all kinds of different dies and things to make it darker

Hey James!! I´ve just made your misture, actually its in the fridge right now. I made the soft wax, but insted of mineral spirits, that i dont know what that even is eheh i used mineral oil!

@WoodByWrightHowTo

3 жыл бұрын

Mineral spirits is also referred to as white spirits in the UK. Mineral oil will make it very soft but mineral oil does not polymerize so it will stay liquid on the surface rather than hardening over time.

@yohannsantos4901

3 жыл бұрын

@@WoodByWrightHowTo Thanks! I see the point, but even as white spirits i cant find it in Portugal: it where im from

@marelizevanrooyen

2 жыл бұрын

White spirits is a product like vodka?

@pecopecof8074

5 ай бұрын

@@marelizevanrooyen its more like diesel fuel

@pecopecof8074

5 ай бұрын

@@marelizevanrooyendiesel fuel or jet fuel.

Is the linseed oil degummed so the resulting paste wax will be less prone to molding?

@WoodByWrightHowTo

3 жыл бұрын

I don't do that for the hard wax. But if I were to use it for a finish I would use the home made BLO that has no issue with mold.

Paint strainers for 5 gallon buckets cost less and do a better job than cheese cloth. A bee keeper.

@WoodByWrightHowTo

3 жыл бұрын

That is a great idea!

👌

I hope you might be able to help...but I made this board recipe and it seemed to have gone rancid. Did I do something wrong? Over a little bit of time it has a pungent smell.

@WoodByWrightHowTo

3 жыл бұрын

Why don't you send me an email and we can hash it out. jameswright@woodbywright.com I don't always see responses on here. They tend to get buried quickly. First I would ask which recipe you're using. Second I ask where did you get your supplies and third I would ask how long did it take for the smell to start. most linseed oils are good to sit on the shelf for a year or two without any problem. Especially if they're kept in an airtight container.

Question: I am looking for the old kind of wax they used on terrazo floors... can this be used on floors to seal and polish?

@WoodByWrightHowTo

2 ай бұрын

yes. though that would have mixed in a bit of protectant such as varnish or shellac.

@wassytrini

2 ай бұрын

@@WoodByWrightHowTo thank you!

The how to make sense. Its the why I'm not clear on. Do you use a Beeswax & Linseed oil mix to save time from putting on Linseed Oil and then Beeswax or is there another reason for using a mix? Thanks

@WoodByWrightHowTo

Жыл бұрын

It does not save time or money. But some people like the enjoyment of making things from scratch. For me I sell it. The other reason people might make it is so they know what exactly is in it.

ive gotten a nice waxed surface by letting the wood sit in the sun and getting really hot then applying the wax and letting it sit for a while then letting it cool and then buffing it out. I tell myself the heat helps the wax penetrate, but idk, it might be the placebo syndrome

@WoodByWrightHowTo

3 жыл бұрын

That's actually a pretty decent method. A lot of people use a heat gun to work it down into the wood. The old-fashioned way is to use a friction polisher.

@joshwalker5605

3 жыл бұрын

Wood By Wright How 2 ok well good to know im not tricking myself!

I wanted to buy some of your hard wax but unfortunately shipping to the UK is really expensive, so I'll see if I can get hold of some raw materials and follow your recipe instead! Thanks for the info

@WoodByWrightHowTo

2 жыл бұрын

so true. usually the shipping is way more then the product! no fun!

@Countryboy246

Жыл бұрын

@@WoodByWrightHowTo around $7 shipping to UK isn't that bad to be fair James it would cost alot more in gas and electricity to make it yourself sir great video

Are your measurements by weight or volume. I saw you weighed the paste wax but the liquid ingredients seemed to be by volume.

@WoodByWrightHowTo

3 жыл бұрын

I generally do by weight. but eather will work fine I am not precise enough for that to make a difference.

Unless you have a beekeeper friend you'll pay more for wax than for honey. Also I'm told you want to warm the wax at the lowest possible temperature. Cooling from a high temp makes a harder wax.

Can we use this as a substitute for Wood Floor Wax?

@WoodByWrightHowTo

2 жыл бұрын

Wood flooring wax used to be like this and you would just reapply it every 6 months or so. Nowadays wood flooring wax is actually a polyurethane. Or something similar that actually adds a coating to the floor.

How do you clean the pots and pans after making the wax? After They're cleaned, are they safe to use for food?

@WoodByWrightHowTo

2 жыл бұрын

Cleaning can be difficult. I just bought cheap ones for 5 bucks at the resale store and dedicated them to the process. But if you were really careful with it, you can clean it out. If you heat it up until it melts you can wipe it out with a rag and then theoretically what dishwasher should be able to heat it up enough to clean out everything leftover.

@KellyVisionPictures

2 жыл бұрын

@@WoodByWrightHowTo Does that apply to store bought BLO as well?

What would one add to do a tinted wax?

@WoodByWrightHowTo

3 жыл бұрын

It all depends on what you want with it. You could add a trans tint dye to it and get whatever you want just to be careful when wiping it on to have gloves otherwise your hands will turn colors. I've known other people to mix in an oil-based stain but pretty much anything that is intended to color wood could get mixed in with it.

Could the linseed oil be subbed out with another oil? Like coconut oil? I use coconut oil and beezwax to make my board butter so i have an abundance. I wanted to use what I have on hand if possible

@WoodByWrightHowTo

8 ай бұрын

Sure you can use any mixture you want. People use all different types of oils and different types of waxes. Just be warned with coconut oil it takes a long time to polymerize and will often feel oily for weeks or months.

@thestrangefire

8 ай бұрын

@@WoodByWrightHowTo Got it! I'll stick to the linseed oil then. Thank you so much for the response and the info. Your channel has helped me out so much as a woodworker!

I live in Indonesia, we cannot get raw linseed oil, can I use boiled linseed oil for the first hard wax? I need it for rust prevention as the humidity here is insanely high. Thx

@WoodByWrightHowTo

2 ай бұрын

sure. just realize it will polymerize on the outside much faster and you will get a skin on top of the wax.

Does anyone know if you can use Gamsol Refined Linseed Oil for this? I have left over from oil painting and was wondering if it'll work. Also if I can use Paint Thinner since Mineral Spirit is banned here in CA😬

@WoodByWrightHowTo

Жыл бұрын

Yes and yes. kzread.info/dash/bejne/lWam266lhpDcpbg.html

@EggyOrphan

Жыл бұрын

@Wood By Wright How To thank you James, wasn't sure if I had asked this question before but as always appreciate the reply🙏

can you use this wax on a wood finished with a water based finish?

@WoodByWrightHowTo

3 жыл бұрын

yes.as long as the finish has cured there is no problem at all. congrats on first.

@JT-hw6mq

3 жыл бұрын

@@WoodByWrightHowTo Thanks. And thanks for all the videos you post. Its great work.

Is the hard wax good for rust prevention on power tool table tops? I have a 10" band saw and a bench top drill press, both with cast iron platforms. Right now I'm using 3 in 1 oil. It works, but I have to reapply it often. The tools are under a an awning outside (one day I'll have a climate controlled workshop, one day). I'm just wondering if the wax will last longer. Thanks! FYI, I just subscribed.

@WoodByWrightHowTo

11 ай бұрын

That is what I use on my metal tops.

@biekgiek

11 ай бұрын

@@WoodByWrightHowTo Awesome, which one? The soft or hard? I’m going to order a tin.

@WoodByWrightHowTo

11 ай бұрын

I use the hard.

"Here comb the wax jokes"

Have you ever worked with Willow? I've been gifted a load and note it's properties lend towards turning, just wondered if you'd experienced it at all?

@WoodByWrightHowTo

3 жыл бұрын

Yes. It has a lot of nice turning aspects. It's a great wood for hand tools and carving as well. And all around very simple easy wood to work with. depending upon where on the tree it may also have a decent amount of figure to it.

@jonathandooley1261

3 жыл бұрын

@@WoodByWrightHowTo Amazing, thank you so much!

I don't know where is my mistake, but my bees hard wax stops the plane instead to move smooth and faster. I will try to melt candle and mix it with liquid paraffine. I will share what will happen.

@pecopecof8074

5 ай бұрын

I made few ratios: - only candle - very hard to apply to the sole and can't feel glide differences . - 1:4, 1part liquid paraffin with 4 parts melted candle - the mixture stays hard like candle and feels little bit oily. Better apply to the sole than the pure candle, but still not good gliding. - 1:3 - the mixture stays hard and feels more oily in the hand. Good apply to the sole, little bit better gliding. - 1:2 - the mixture stays hard again and feel very oily in the hand. Very good apply to the sole, very good gliding. - 1:1 - the mixture stays hard at first look, feel very very oily and feels like starts to melt in the hand. Apply to sole very easy and glide like 1:2 mixture. 1:2 think is the best mix for me. Twist cans from paper glue were filled, so the wax will stay clean and easy to use. I'm pretty sure Rob Cosman's wax is on the same base. Not so much variants for wax i think. The bees wax i will use for wood protection, just doesn't work for me as lubricant. Happy planing guys! :)

Can this be used on cast iron for rust?

@WoodByWrightHowTo

Жыл бұрын

Sure.

where did you get that can for your wax? Also what purpose does the mineral spirit serve in your wax creme? I ask because I've see DIY recipes for wax creme that just uses wax, coconut oil and some other oils.( I'm trying to save a buck or 2 if I can) thx again for this video♥☻☺ I really enjoy watching this video double time. In fact the next time you make these videos if you can say the work puck​🐔​🐥​​🐔​🐥​ ALOT... it would be super entertaining. ​🐔​🐥​​🐔​🐥​You did a FEW times this video.. but many pucks in a row often makes my memory retention GREAT!!! 🐔🐔

@WoodByWrightHowTo

2 жыл бұрын

The mineral spirits makes the wax softer and easier to apply. It then will evaporate them away leaving the hardened wax behind. It's not necessary but it makes it easier to apply.

@ArtWars314

2 жыл бұрын

@@WoodByWrightHowTo ahhh!!! ♥☻☺ Can I use rubbing alcohol instead? thank you * puck puck puck!! *** 🤣😆😂 🐔​🐥​​🐔​🐥​🐔​🐥​​🐔​🐥​

Is this food safe? Can I use it on wooden kitchen utensils? Thx for the video

@WoodByWrightHowTo

Жыл бұрын

I use it on my wooden kitchen utensils. but food safe is a personal choice. different people draw the line in different places.

@poya1981

Жыл бұрын

@@WoodByWrightHowTo Thx for quick reply