Making a Drill Bit Sharpener - Hemingway Kits
Ғылым және технология
Here I have a go at making the drill bit sharpening attachment for the Worden tool and cutter grinder.
Some of the tools I use and would recommend:
Starrett Edge Finder: amzn.to/3wLbqRp
Dykem Layout Fluid: amzn.to/3Tp2Xw1
Starrett Hacksaw Blades: amzn.to/3PdsbuW
CT-90 Cutting and Tapping Fluid: amzn.to/49TH4uo
Eclipse Scriber: amzn.to/4c6Ck6w
STA-BIL Rust and Corrosion Inhibitor: amzn.to/3wFSbIJ
Dremel 3000 Rotary Tool: amzn.to/3Pa3gIH
Trend Digital Level Box: amzn.to/49Z0dee
Sealey Imperial Hex Key Set: amzn.to/3wJFvRd
ElectroCookie Solderable Breadboard: amzn.to/4a1Dez5
Mitutoyo MIT103-129 Micrometer: amzn.to/3wDB9ei
Mitutoyo 103-130 Micrometer: amzn.to/3V4lEGr
Engineer Solder Sucker: amzn.to/438RFiT
3M Silicone Face Mask: amzn.to/3SYOLbu
Irwin Hacksaw Blades: amzn.to/3TpLOlK
Irwin Metal Hacksaw: amzn.to/3V6SvKI
Starrett 117D Centre Punch: amzn.to/3V6hRIG
Big Gator Tools V-Drill Guide: amzn.to/3Tq6hXP
Faithfull Engineers Square: amzn.to/48Jt05p
Milwaukee Set of Drill Bits: amzn.to/48O9uVo
Пікірлер: 23
Great project for a home shop. Thanks for sharing!
@PaulsGarageProjects
Ай бұрын
Many thanks!
Excellent work and craftsmanship! Try a more shallow point for steels like 135°. The length of the 118° point is more ideal for softer materials such as aluminum or non hardwoods.
Great project and nicely made, thanks for sharing
@PaulsGarageProjects
Ай бұрын
Thank you! Cheers!
nice work! Thank You!
@PaulsGarageProjects
Ай бұрын
Thanks!
great video. and well edited. whats the type of grinder & wheel your using? not seen anything that looks like that before?
@PaulsGarageProjects
Ай бұрын
Many thanks! It's a Worden Mk 3 tool and cutter grinder that I built recently. I'm using a 100mm, 60-grit, aluminium oxide, taper cup wheel.
Nicely nice chap ... very Nicely made videos to .... nice one... peace
@PaulsGarageProjects
Ай бұрын
Many thanks for the kind words!
Nice video and nice project 😀👍... But.... tapping with a jacobs keyless chuck ?....is a big nono and asking for a broken tap
@marley589
Ай бұрын
Use the right tools for the job and never a problem with keyless chucks.
Yup good video no f ing about get on with the show and show us the results, good show mate
@PaulsGarageProjects
Ай бұрын
Thank you very much!
@JibrhanKhan-lw2lk
Ай бұрын
@@PaulsGarageProjects your very welcome
👍😎👍
I thought you did a fantastic job. Making parts you could have bought was a bit much. I'm working on one for MT bits. Very few parts. My dilemma is the bits sometimes start off 18 inches long and can be reground to 7 inches. Counting the MT and given the bits use. Just for the 3/4-2 inch bits
If your a hobbyist then your doing great! But if not and this is/was your profession, then why aren't you counter sinking before reaming and tapping?! 🧐
@PaulsGarageProjects
Ай бұрын
Many thanks for the tip! I'd heard that it's a good idea to countersink before tapping, but didn't know about reaming.
@Dagonius.
Ай бұрын
@@PaulsGarageProjects Your welcome! ALWAYS chamfer prior to tapping, reaming,...
@tonyray91
Ай бұрын
Ref hand tapping in the mill you will notice that most taps have either a point on the end of the driving square or better a centre you can use this to keep the tap vertical: Let’s say the tap you want to to use has a centre, find another tap that has a point on the thread end and put this in the drill chuck, put the threading tap in your tap wrench and locate in the hole to be tapped, lower the quill and use the point of the other tap as a centre in the end. Put a drop of oil on the centre, as you tap keep a bit of pressure on the quill to keep the centre locate as the tap winds in. For tape with a point you can use a mating tap with a centre in the threaded end usually found on bottoming taps, it helps if the centring tap is a similar size You can make a spring loaded centre to replace the locating tap which make the job easier. Thanks for sharing I have a Mk1 Worden and the same kit that I’ll be making for it.
@PaulsGarageProjects
Ай бұрын
@tonyray91 Just finished making myself a spring-loaded tap follower, which should do the trick 👍