Making a £13000 turntable
Тәжірибелік нұсқаулар және стиль
Another daily grind video, this time the full construction process of a Garrard 301 turntable plinth from start to finish. These layered ply plinths are what I most commonly make.
Affiliate Links, As an Amazon Associate I earn from qualifying purchases;
Tools used-
Yorkshire tea- (UK) amzn.to/2WUYBlv (USA) amzn.to/3heqfRQ
filler gel- amzn.to/3iyUVyl
beeswax for drawing circles- (UK) amzn.to/3fJExZO (USA) amzn.to/3hfvalw
Ruby stain- (UK) amzn.to/3lKteEw (USA) amzn.to/3jUijXH
super glue and activator- (UK) amzn.to/37v6obC (USA) amzn.to/3DZcoZb
Festool router- (UK) amzn.to/3zXawhc (USA) amzn.to/3tnSmTx
guided cutter for recess- (UK) amzn.to/3xGzmjH (USA) amzn.to/3hxbAS3
Titebond 50 glue- (UK) amzn.to/3ndFnCC (USA) amzn.to/2X6CPM6
Special hot veneer press tool- (UK) amzn.to/3jQLaMu (USA) amzn.to/3DZlNQF
UK only- Get a free month when signing up to Smarty, sim only mobile, it is what I use, unlimited minutes and text, data is capped so you never go over, and unused data is discounted every month- i.smarty.co.uk/24Mwjc
The plans and supplementary info for some videos are now on my patreon. you an also help by supporting me to make more videos, and get access to extra content-
Patreon- / newyorkshireworkshop
edit to add, forgot to mention a thanks to Bob at Inspire Hifi for providing the last clip of the completed turntable in use.
The music used was Blow the man down by the Midshipment glee club from the KZread copyright free music library. this is not the original music being played in the clip; I had to edit in the above to avoid copyright infringment.
Пікірлер: 5 700
No high-speed video, no horrible royalty-free music. Finally something that's a pleasure to watch.
@wongwongping
Ай бұрын
Good works
For any woodworker there is a HUGE wealth of shared knowledge here. Grits, tools, adhesives used - dust management - etc., etc., etc. Thank you for sharing your knowledge. It's uncommon to see a fine crafts-person sharing lessons learned over many years.
really enjoyed watching a skilled craftsman working with quality materials and tools creating such a beauty.
This makes me miss my grandpa and his amazing woodworking ..
Another random recommendation from the algorithm. I'm a sucker for a skilled craftsman making ANYTHING it seems. No interest in turntables whatsoever, couldn't stop watching. Nicely done!
@outsidethepyramid
3 жыл бұрын
another "algorithm" comment rears it's unimaginative head
@ChrisB-wl7ci
3 жыл бұрын
Me too!
@thespicywolf8818
3 жыл бұрын
well it was random
@happywilliam1
3 жыл бұрын
same here!
@LuizDahoraavida
3 жыл бұрын
it's an algorithm, it's far from random
I'd normally find it very difficult to watch a 35 minute video straight through from beginning to end but this had me totally transfixed. A master craftsman at work is really something to behold.
@donwa9851
2 жыл бұрын
So, you don't watch normal television shows? What's the difference?
@InvincibleGaming1
2 жыл бұрын
same
@jampstudios3314
6 ай бұрын
Same here!😊
@brianmorris8045
6 ай бұрын
Absolute work of art with pride attached.
@scotthutch3682
6 ай бұрын
2x speed man 😎
I love watching videos of craftsmen and women making things … it’s one type of video were no talking works really well. Unless of course it’s a tutorial video but watching something being manufactured is just really therapeutic. Thank you for sharing your skills.
there is nothing better then something handmade/crafted by a master, i am in awe of this level of skill
I’m a woodworker and sat and watched this with my audiophile husband last night and we were both transfixed! 😍 Marvellous craftsmanship and fabulously shot & edited video too!
@sasproductions701
2 жыл бұрын
omg ur profile pic yum.. hi to you and your HUSBAND!
@sasproductions701
2 жыл бұрын
@Kontruksi Aman & Selamat Official thats a nice skatepark.
This is what’s best about KZread, being able to watch a very skilled worker in action, brilliant and inspiring !!
@joeygonzo
2 жыл бұрын
this man is a legend
@heru-deshet359
2 жыл бұрын
Not a very skilled worker. An artist.
@bigb0ss282
2 жыл бұрын
STFU, that was basic and the wood was CHEAP.
@monk1100
Жыл бұрын
Its wicked art from start to finish. These are the videos that keeps you up all night 😂
@rogerphelps9939
5 ай бұрын
The whole task is futile and a waste of time. Vinyl is objectively very inferior to digital
I was wondering how come something this expensive can ultimately be made of plywood. Then I googled the cartridge alone!!! Jesus.
@bobbg9041
6 ай бұрын
35:22 depends on type of plywood How many layers whats it made of How stable is it, hell B&Ws are made out of MDF its the perfect material it stable dence and flat. Dont judge somthing by the fact its plywood thats probably cabnit grade birch 15 layers 3/4" and cost about 150 usd a 5x8 sheet or something like that. Its hard and has no voids, this isnt your standard 60 bucks a sheet construction grade plywood Hell some of these can cost 200 bucks usd a sheet.
@user-sd3ik9rt6d
6 ай бұрын
It's not ply because it's cheap, it's ply because it works the best for the task at hand.
@EnginAtik
6 ай бұрын
The materials and the Ruby color are classic.
@bjornlangoren3002
6 ай бұрын
During the height of the post pandemic supply chain issues, we got birch plywood much cheaper than construction plywood.
@1Uncle43
6 ай бұрын
Less prone to warping? Pressure treated?
One of the most rewarding projects I've ever watched. Astonishing to me that you didn't get confused. I certainly would have.
Not with standing the cost - it was lovely to see a craftsman create something lovely and taking pride in what he was doing. simply wonderful
@Developer-online
3 жыл бұрын
You have no idea how much amazing craftmanship ended up scrapped thrown out as garbage because of some new fashion coming to the marked . we throw and use too much and not caring for what we have.
@vindicari
3 жыл бұрын
plywood ? hardly a high quality material.
@klashnacovak47
3 жыл бұрын
Craftsmanship has nothing to do with quality of materials used but the quality of how the material is used.
@pdstokes8
3 жыл бұрын
@@vindicari plywood is often used as it is so stable, absolutely nothing wrong with quality plywood.
@rickg8015
3 жыл бұрын
@@vindicari That’s Baltic Birch Plywood.. Highly dense. Void-free. Not ordinary marine plywood.
This isn't a turntable, it's a work of art. Congratulations!
A beautiful plinth and very well made. I made a cheap budget version around 50 years ago, and used a secondhand Garrard 301 with an SME tone arm. I was using a Quad amp and Tannoy speakers, and was very happy with it all for years. But with the new CD’s, it stopped being used, the albums were given away, and after years of gathering dust the whole lot went to the dump. Seeing the 301 in this video prompted me to use google, and now I am crying after seeing the what it would all be worth today….
Magnificent video. It fills me with absolute awe and joy that (respectfully) such compulsive craftsmen still exist in the total lunatic pursuit of perfection. Please send me one for this endorsement! Thank you.
Beautiful work. Love the use of layered plywood to allow a wooden chassis to be created yet with the dimensional stability required for such high end audio components. Each piece will be totally unique as well.
I'm lost for words, nothing to say ... just WOW! Beautiful work, looks amazing.
Filled me with nostalgia! I worked for Garrard Engineering in the 1970's in research and development. I even had a 301, but stupidly sold it years later. Thanks for the wonderful video.
@GpunktHartman
Жыл бұрын
Fold the cd in half, place it into youre Mouth, then hold two needles , left and right between thumb and a finger, and stich them direkt to the 230V Powersource...
@willb1157
Жыл бұрын
@notfiveopreheat oven to 200 c......
@CaptainDarrick
4 ай бұрын
Didn't the Garrads use big idler wheels ? Eeeeek...what were they thinking?
@PeterRabbit70
3 ай бұрын
Mom and Dad bought a Garrard turntable, and a Stromberg-Carlson tube amplifier in 1958-59, maybe. Good sounding unit for Frank Sinatra, Pete Fountain, Ella Fitzgerald records they liked to play. I took it to Auburn in 1970, to play The Who, Grand Funk, Mountain, and Creedence's John Fogarty. That setup was bulletproof.
No matter how long the video is, I enjoyed every minute. The master craftsman presented a top product, without hiding a single segment of the production process. Anyone who thinks they can produce the same product, please try the same process, I personally think I have some experience, but I honestly wouldn't go through that process. there is a reason why the product is so expensive.
Wow, been sitting here trying to come up with the words to convey my thoughts/ amazement of your work. I know I've never seen a turn table if this quality. The finish is mind blowing and the parts the customer supplied were just beautiful. Thank you for sharing your work!!
I’m amazed how you can be a master of so many crafts. Awesome work and shows the importance of having the right tools for the job.
Absolutely amazing work! True craftsmanship and a bit of a lost art these days. Beautiful. Thank you for sharing this.
Always a pleasure to see a real 'professional' in action! Simply beautiful!
Man! That is a thing of beauty - the skill, care and pride that go into making that is incredible.
@rogerphelps9939
5 ай бұрын
It may be a thing of beauty but is the equivalent of creating a modern copy of a primitive car. Poin tless.
@dennisroach5424
5 ай бұрын
@@rogerphelps9939 bit like your comment :D
Now that is what I call craftsmanship, impressive
Absolutely wonderful piece of art, your care and attention to detail just takes your finished piece into another level.
Mesmerizing build! I thank my lucky stars I will never be burdened with this level of connoisseurship... just a country lad with simple (and affordable) tastes.
That was the fastest 35 minutes of my life...utterly fascinating and I'm blown away by the final product...awesome!
@ezequielcronswell8520
2 жыл бұрын
I can build that turntable for only $1000 USD
A phenomenally beautiful way to listen to and preserve vinyl.
Gorgeous work of art! It's always funny hearing pops and clics when a record gets played on a £13000 turntable.
@BUF-vr5cr
Жыл бұрын
You are not hearing the actual turntable playing a disc. “The music used was Blow the man down by the Midshipment glee club from the KZread copyright free music library. this is not the original music being played in the clip; I had to edit in the above to avoid copyright infringement.”
@steven2809
Жыл бұрын
It's not funny...it's annoying! 19th century technology....😖
@BUF-vr5cr
Жыл бұрын
I guess you realize it is the record not the player that causes the pops and clicks.
@steven2809
Жыл бұрын
@@BUF-vr5cr 😣
@ericsyre9418
Жыл бұрын
@@BUF-vr5cr Of course I know that, but still funny to have such a high end piece stuck with low end pops anyway.
Landed here by accident, what a pleasing video showing some fantastic skill, stayed to the end and had a smile on my face. Quality work m8, all it needs now is a teletubbies lp to test it out :)
Considering the hardware accounted for ~10 or ~11k of the price, I think the remainder for your materials, time, effort and expertise is extremely fair. Amazing craftsmanship.
@Josef_R
2 жыл бұрын
And he left out the $3-5000 for the turntable.
@prestonian1066
2 жыл бұрын
@@Josef_R I'm sure that's just the cost of the parts supplied by the customer and doesn't include whatever was charged for making the plinth.
@andrezesna3920
2 жыл бұрын
If you use records they worn of everytime a needle goes over it.
Wow, amazing work. Thank you so much for filming this. This is a masterpiece.
Beautiful work my friend! You are a true artist! I find your channel both relaxing & inspiring art the same time... Thank you for making these great videos!
Watched this video before, the end result is just exquisite, beautifully made with such care, I’m sure the owner of that assemble deck would be very very pleased 👌👌
Such a treat to watch. Every step is more beautiful than the last.
That was an honour to see such workmanship created. A discerning customer indeed . Thank you for uploading
I've watched this video in it's entirety twice, and all I can say is WOW!
I won't lie. Early in the video seeing the wood used - I was sceptical. Then I was blown away with the mastery on display here. An immensely gratifying end to the video.
@africanhistory
2 жыл бұрын
yeah plywood at that
@GamezGuru1
2 жыл бұрын
that's cos stacking plywood and wrapping it in veneer is cheap, and whoever paid 13k for this is stupid...
That was absolutely stunning, the attention to detail was stunning. The arm and cartridge were pretty sweet as well...
@chrishatton2642
Жыл бұрын
Totally agree. Beautiful woodwork, but man, that tonearm and table certainly matched the level of craftsmanship.
Beautiful. My dad would've loved watching this as he was both a quality old school joiner and a HiFi buff. Lovely work 👍
I am astonished to find people are interested in record players again. My dad designed and manufactured Orpheus Silex Turntables, and I was bought up in the light machinery workshop. Nostalgic to watch this video
@tooltime9260
5 ай бұрын
Why would you be astonished for people to be interested in turntables? Are these people mentally deranged in your eyes? It's a machine like any other with people who appreciate things even though some shallow thinking people think they are out of touch with modern life. Get real.
My lps from my early teen years (70s) survived the department record player (ceramic cartridge) then moving onto a MCS component stereo. My older brother taught me how to clean and handle the lps. I still enjoy them on my Fisher and Techniques (80s/90s) turntables.
A very very high standard of craftsmanship. Pleasure to watch. I do pity the poor sad immature people that down voted this work.
I never tire of watching a skilled craftsperson. This is a work of art!
@petermasterson8276
3 жыл бұрын
Craftsman.
@ginaschmitz4755
3 жыл бұрын
It has nothing to do with art. It's just skilled crafmanship. Art needs something more than to build a plinth after a simple plan and finish it nicely.
As I've been doing for about 40 years now I use digital media, however I found this very intuitive and would like to thank you for a wonderful lesson
Nice! I too am a 39 year old life long woodworking enthusiast.
Birch ply is one of my faveourite mediums and so stable and versatile. This record deck is a work of art my friend.
Fantastic craftsmanship. Glued to the video if you pardon the pun ! Nice to know that in these days of mass production the craftsman is still alive and well. This beautiful turntable makes my Project look a bit ordinary !
This is a YOUNG genius/artist at work. The skill is making it look like anybody could do it.....we can't. Congratulations young man, you should be very proud of your skills 👍👍👍
@waynepayne864
Жыл бұрын
bro what why do u keep calling him young thats kinda weird
@jeffleigh3747
Жыл бұрын
@@waynepayne864 because he's not old. He's learnt his craft quite quickly .... considering these skills take years and years to perfect
That is beyond beautiful 💙 The colour, the shine, the hours of work, breathtakingly beautiful 💙
@sorinichim4737
3 жыл бұрын
Not forget...the price !😅
@SG-uh6sw
3 жыл бұрын
Give this man a ❤
@j.m.w.5064
3 жыл бұрын
This is so incredibly ugly. He is good. He did well. My respect. Mad skills. But now the wood looks like plastic imitating wood. I pity this piece of wood.
@richarddrolet7746
3 жыл бұрын
And friends is why cd is OUT.
@LucidPreditor
3 жыл бұрын
It's just a bit of wood, not worth the money.
I started work life as a coach painter at 15 in 1973. We used to wet the floors for painting back then. Hard to believe that we could get a finish like this with brushes. I’m 62 now and still could.
@alext8828
3 жыл бұрын
Yes! You can get quite an amazing job with a paintbrush or especially a small foam roller. It leaves enough paint on for a decent cut and polish.
@CHewittMedia
3 жыл бұрын
Would you make a video showing this technique? I'd love to see how that could be done with minimal equipment.
@bryngerard4334
3 жыл бұрын
Interestingly, I began work at the same time in a piano restoration workshop. We used this method of polyester spraying shown in the video way back then. I know it quite well because as the new boy I did most of the sanding and polishing with red soap then the white :) Watching this brought back alot of memories.
@robertnicholson7733
3 жыл бұрын
I am an old-fashioned sort, but I used to do a fair amount of synthetic clear finishes when renovating houses, I also used to do some work on vintage gramophones, etc. for friends. There used to be a far greater selection of finishes available 40 years ago in Australia, one I used a fair bit but has been unavailable for a very long time was a "pulling" lacquer, this lacquer could be applied by spray or brush (if you were brave) and was then pulled flat using a pulling liquid and rubber - much like French polishing. The trouble with brushed finishes is the sanding required, which I usually do by hand. I use wet and dry up to 10,000 grade - worn if possible. In most cases little polishing is required after this and when required I use a friable material like Tripoli. I also have used and still use, other grades of rotten rock, various grades of pumice , talc, and plain flour depending on what I am polishing. On houses, poly and acrylic finishes are the way to go but I just don't like them on anything fine. To me, if you build them up, they just look plastic and when you don't, they look dull and uninteresting (they kill Australian Red Cedar, aka, Toona ciliata, Cedrela toona and Toona Australis). The same with the clear pouring epoxy resins, great for protection, but they don't really do it for me. Don't get me wrong, I have used clear epoxies for protection on high wear surfaces and heavy weathering surfaces, but I think they kill the grain. I repaired a croquet mallet by inletting, banded, heavily interlocked, River Red Gum into the corners of the mallet to replace the damaged wood, this intense, naturally very dark, beautiful red wood was killed dead by the epoxy - most disappointing, I should have used an oil finish but I didn't have the required 6 months. For me, I just like Tung nut oil and shellac, the Tung to bring the colour up (and seal the wood), I believe the modern phrase is to make it "pop" and the traditional French Polish finish. Yes, French polish can be damaged reasonably easily and does deteriorate if not looked after but it is so easy to repair and even refinish. AND, in my opinion is the best looking high gloss finish - bar none. Nothing beats looking deep into the grain from directly above while bringing down your fingers, you can never tell exactly when you are going to touch the surface. Beside, French polishing large flat surfaces is therapeutic, especially in the final spiriting off phase, just watching the rubber going over the work while the gloss comes up, mesmerizing, just don't let the rubber stick! I have put this at the end of my comment as few will bother to read to the end, so I won't get the usual flame stuff. Despite all the "just beautiful" comments, I just don't see the skill in this sprayed finish and I doubt I would like it in real life.
@bryngerard4334
3 жыл бұрын
@@robertnicholson7733 I am a bit of a traditionalist myself but the modern age is reducing access to the materials once in abundance and the new chemicals have been designed to work well with modern materials. I blame minimalism and IKEA myself ;) But seriously, my comment was to reveal that the polyester spraying is hardly new. I worked in a piano restoration factory and people wanted their piano back yesterday and the firm needed to make a profit. That world is largely gone now except for the wealthy. I have a friend who is a leading expert on German Baroche furniture and he is fully trained (got his Masters ticket in Paris) in Antiques restoration. He makes a good living because there are plenty of customers in Germany with the wealth. Myself, I am just a dabbler nowadays. I have been into making things from reclaimed wood stock but even that is becoming scarce and expensive. Then you have to add the cost of making the wood usable. The real cost of recycling is unknown to most. Less old properties to demolish and the demolition guys were a great source of old wood for me :( But I embrace new materials although some of them I find difficult to become fond of. Thanks for your reply, I enjoyed reading it.
I was mesmerised. You are indeed an Artisan. The Care and Love you Impart to your work is an Absolute Joy to watch. Thank you for sharing.
Beautiful craftmanship. You know you do a lot of woodworking when you have a 5 gallon pail of Titebond.
"Gorgeous" doesn't come close to doing justice to this piece of art.
@beardsntools
3 жыл бұрын
Nah it's not really that impressive and profit margin on this must be huge lmao. The only problem could be time, but that can be solved. A week in a heating room? Make multiple at same time.
@tomhicks1009
3 жыл бұрын
Harsh Nemesis profit not that huge as the components cost 10000 The hrs put into this piece is astounding. Highly skilled and an amazing finish
@tasmedic
3 жыл бұрын
@@tomhicks1009 no Just, no. It's all show and little in the way of materials. Plywood is, well, just plywood. It costs little, is durable enough, but not a premium product. Putting stained, low quality hardwood veneer over it is just putting lipstick on a pig. It looks lovely, but it's just basically laminated crap with a cherry on top. "automotive clear coat" is a cheap, quick and crappy alternative to French Polish. If you think this has a good finish then go to a local auction and look at an old piece with French Polish on it. We've definitely gone cheap and cheerful since those days.... Well, maybe "expensive, and crappy" instead.
@JorgeRosa
3 жыл бұрын
Agree! A real piece of art, no doubt.
@scottsorensen239
3 жыл бұрын
@@tasmedic I agree at this price point I was surprised to see plywood and veneer as well.
Last vid I saw of yours you were renovating some stairs... then this pops up and I'm stunned by your workmanship. I think I'd better subscribe mate I sense there's a lot more to come.
@phlav0r
2 жыл бұрын
HA! I was wondering why this was in my feed. It ticks a lot of boxes for my interest but you just made me realise who I was watching. This guy needs more subs.
I’m an audiophile, and my dad bought me a Garrard solid oak turntable when I started H.S. . I had it for close to 20 years. The turntable you created brought back happy memories, thank you.
@Alptraumification
Жыл бұрын
I'm an average music enjoyer and I agree about the memories being brought back.
@-First-Last
7 ай бұрын
"audiophile" ??? What's so special about you ?
@darwinawardcommittee
6 ай бұрын
I’m half deaf and this thing is pretty sweet!
@sirmalus5153
6 ай бұрын
@@-First-Last You don't know because you've never met one obviously.
@-First-Last
6 ай бұрын
@@sirmalus5153 😂😂😂😂😂😂😂😂😂😂😂😂😂😂
For that bank account fulla bucks I'd have been betting on a billet block of solid bubinga...but boy was I bewildered to see birch plywood and modern glue!
I spent most of the time just looking at your shop (impressive layout) Will now have to watch again for the project
やっぱり良いものってのは、気が遠くなるほどの手が掛かってるんですねえ。こういう見事な製品は、使う側の人も研ぎ澄まされた耳を持ってないと宝の持ちぐされですね。良いもの拝見させていただきました。many many thanks でした。from japan.
Mad skills! So beautiful. I bet I dream of this tonight. Thanks for taking the time to share.
What beautiful workmanship! There's a plaque on my wood shop wall that reads, "Cleanliness is next to godliness...but in this shop it's next to impossible."
I watch a lot of “semi pro” woodworkers, just shows what an actual pro can achieve. And a fellow Yorkshireman to boot. Loved it pal.
Lovely piece by the end. However, I was holding my breath as those last screws went in, especially the power lead socket with a battery drill...one slip and catastrophe.
@fatfreddyscoat7564
2 жыл бұрын
I had a wobble when the owner unboxed the tone arm etc and just opened the wooden box and rested it on the plinth!
@sharonmustac8047
2 жыл бұрын
i thought the same thing when i saw it, it had to be done slowly by hand.
@laszlobarchet2646
2 жыл бұрын
Don't worry guys! He IS a skilled professional.
@joytekb
Жыл бұрын
I am completely ignorant but think maybe to use ratchet.
@freepress8451
Жыл бұрын
Hahaha had exactly same thought, with flat-head driver. . . .allen key
I did a very amature 401 build many years ago and I've had a 301 sitting around for decades that I intended to turn into a much more serious project but sadly I never seemed to have the time, inclination and resources come together at the same time. Seeing the amount of work you put in to produce such a stunning plinth makes me realize that the project was probably a bit beyond my scope anyway.
Incredible craftsmanship! Beautiful work! Thanks for this video. Fifty years ago, I had ears that would have appreciated and enjoyed a 13000-GPB turntable. Now, I have ears that can appreciate and enjoy a 13-GBP turntable.
@GarryAndrews_
2 жыл бұрын
Well I appreciate your comment
Have been glued to this screen for every second of this. Thank you for an amazing look into how this beautiful turntable was created.
Awesome finish. It requires monumental patience to give this quality. Enjoyed it yo the core.
British design & craftsmanship. Nobody does it better.
My intention was to ff through the video for an idea of how it was made but it was most fascinating watching a craftsman at work that it had my attention from the measuring and cutting of the ply sheets all the way through to the final assembled masterpiece👌
The craftsmanship is unbelievable... I know nothing about building a turntable but it stands to reason that building materials, sound quality, vibration, stability and components are much more important than the overall look.
@ginaschmitz4755
3 жыл бұрын
unbelievable? You are no craftsman, are you? This is basic work everyone could do with the right machinery and profession.
Absolutely stunning! I now want to build my own turn table. This is such a cool art!
A gorgeous build, impressive craftsmanship. This also proves what I´ve thought, that audiophiles are some of the craziest people on the planet.
@dominicfield8022
2 жыл бұрын
Particularly when the physics of the record disc are such that you can never improve on about 5% distortion!
@CaptainDarrick
4 ай бұрын
@@dominicfield8022You miss the point . They don't care about perfection in sound ..that's not what vinyl is about
Wow! Thank you sir for sharing this! Fascinating to watch all the bits come together so beautifully...
I don't know how this came up in my feed, but I'm so glad it did. Just jaw dropping craftsmanship from start to finish. Such skills are honed over years to create a masterpiece.
@tasmedic
3 жыл бұрын
No, mate. Plywood, templates, wobbly "planes" (actually jointers), thin veneer and stain do not make a "masterpiece". 5 layers of French polish is craftsmanship, not "automotive clear coat". Not only are the skills being lost, but the ability to distinguish true ability from shortcuts also seems to be disappearing. If you think this is 13,000 pounds worth of product, then I doff my hat to you. Let it be said, though, that there should also be a product worthy of 26,000 out there to compete with it, probably fabricated by older hands. I do hope I'm right, because if not, then something truly special has been lost...
@treborreissul
3 жыл бұрын
Exactly crappy turntable,
@VCthaGOATdunker
3 жыл бұрын
@@tasmedic Alright old man.
@TIAG0MAGALHAES
3 жыл бұрын
exactly the same...damm my skills...ill ask my father - lol
@justlookingaround9834
3 жыл бұрын
@@tasmedic Isn’t the arm and cartridge £10k on it’s own?
Gorgeous piece. Truly exceptional, artisan-level work. I was amazed by the speed of some of what you did - particularly the trimming of the veneer (I’d be terrified that the waste material would tear at the finish material). Greatly appreciate you sharing the details at each step of the process.
@christopherbedford9897
2 жыл бұрын
Some of the video is speeded up to avoid tedium 😆
@brentwalker3300
Жыл бұрын
As long as the glue is good the veneer usually tears clean. But yeah, I used to make furniture and trimming veneers is always a little scary.
@arconeagain
Жыл бұрын
It looked to be a very good tool. It also looked the most satisfying of the entire job to me.
😂 I got a chuckle at the “ladies” restroom bit. Good job on the record player.
Stunning craftsmanship, makes me love LPs again.
That was so incredibly satisfying to watch.
@SardarTariqMahmood
3 жыл бұрын
kzread.info/dash/bejne/a4eK0pabYMTVZ7w.html
I'm 10 seconds in and I like this already. No talking, no nonsense gets right to the business, quick, like a bunny... Ol Sarge...
You are very gifted to be able to have that type of job where you are there to please so many people.. Great video & well worth the time watching.
I see so many "wannabes" on KZread. You, my friend, are the real deal
Sounded amazing through my computer speakers.
This is the work of an artist. Congratulations!
@andrewwood640
3 жыл бұрын
@@SardarTariqMahmood SPAM
@iamthetinkerman
3 жыл бұрын
not really, just having to right tools!
I’ve never seen a more beautiful turntable. Amazing
An absolute work of art. Superb quality from start to finish.
The last time I bought a 301 it was 40 quid with EMI pick up and arm. (Decca style cartridge). It came with a heavy duty plinth.
I may never rise to this level but it's sure immensely pleasing watching those who have
When the 301 was current, many were mounted in concrete plinths to provide mass. My hi-fi dealer had a pair mounted in granite. My first transcription deck was the 401, which cost me around £25 in the 1960's! Rim drive decks were fine with mono cartridges but with the advent of stereo their potential shortcomings were highlighted by the stereo cartridges which could reveal rumble on wide range speakers. This wasn't an issue for me until I acquired a pair of Cambridge R50 transmission line speakers. and I had to retire my 401 for the first Linn LP 12 belt drive. No runble, but I did miss the strobe speed setting. It looked very professional. With the torque of the huge AC motor there was hardly any drift. Now if only I had bought a 301 and somehow managed to hang onto it, it would have been the best investment I'd have made. Seeing it mounted in this glorious plinth brought back memories.
Fantastic work - was mesmerizing watching your craftsmanship. Well done!
That has to be the most beautiful piece of work I have ever seen. The finish on that wood is absolutely breathtaking.
@andrewwood640
3 жыл бұрын
@@SardarTariqMahmood SPAM
@TheShornak
3 жыл бұрын
@@andrewwood640 um, what just happened.
This video has been such an inspiration so I built my own plinth and veneered for the first time, definitely a learning curve and I plan to build more plinths in the future.you are a true craftsman and I take my hat off to you.many thanks.
I feel very lucky to watch this video. You are " EL MAGNIFICO ". Unbelievable craftsmanship.
That is fantastic craftsmanship. You could make a living selling those turntables. WOW 😳 absolutely beautiful. Thank you for sharing your videos, God bless 🙏
Absolutely incredible job. I wish I had the tools, skill, knowledge & patience to complete a task like this. Alas, I'm pretty useless.
WOW! You are simply amazing 🤩 I could watch all day.
Really and truly, A PIECE OF ART. If it sounds as good as it looks then it's GOLD.
Just subbed. Really enjoying watching you wirk so many varied project's. I'm totally useless but get alot of knowledge and pleasure seeing this. One of my pleasures is seeing all the different equipment you have. Think I'm a artisan nerd!
I try to explain to friends how I was literally never bored during lockdown thanks to the generous supply of stunning artisan videos like this but they just don't understand 🏆
@GeoHvl
3 жыл бұрын
I get it. I understand also why this turntable cost $16,000.00.