Maintenance Clutch Replacement Part 2(2008 Suzuki SV650-S) ft. Chris
Part 2 of 2. Switching out the clutch plates/fiber plates
Жүктеу.....
Пікірлер: 26
@JackstandJohnny12 жыл бұрын
This is hands down one of the best video write ups I've seen on anything pertaining to a motorcycle. Great job man, very articulate and specific and that goes a long way with stuff like this. Ill be using these two videos as a guide as soon as my clutch takes a shit.
@kholcreates3 жыл бұрын
Thanks a lot man, going to attempt this myself. this vid still helping people in 2021!
@WilksMotovlogs14 жыл бұрын
He probably saved himself several hundred bucks in labor cost doing it himself. great stuff.
@ridered77710 жыл бұрын
He doesn't say it, but the factory service manual says 7ft/lbs (10Nm) for torque on the clutch spring set. They do not indicate one for the install of the clutch cover
@dulayasaennok672511 жыл бұрын
Excellent! You show that it's much easier than what people think to be. So clutch is kinda like brakes. I always thought it's just two pieces of metals putting together.
@calicr20087 жыл бұрын
thanks bro! this really helped me to replace the clutch con My Vstrom...
@cashstore114 жыл бұрын
@199Xray Thanks for the advice. Normally people assume a modern Ducati. I have a 74 750. It's probably much different than what you are thinking. I checked two adjustments on the outside of the bike. I think I have to go in.
@jakopath72 жыл бұрын
You made this look easy. @4:35, thanks for the Mario Land :)
@keaponlaffin6737
2 жыл бұрын
awesome indeed! 👍👍
@360vstrom13 жыл бұрын
change your smoke detector battery every spring
@denniswirths6440 Жыл бұрын
Well done, nice Videos
@DriveCarToBar11 жыл бұрын
Nice vid. I have a V-Strom 650 making some funky clutch noise with about 31k miles on it. I was a little concerned about doing it myself but this doesn't look bad at all.
@brazenbruklen11 жыл бұрын
thanks Bike guys nice vid very well did thank you thank you and as for at 7:00 minutes with the cat AWESOME if I wasn't going to subscribe you got me with that One
@keaponlaffin67372 жыл бұрын
6:49 thumbs up for the jungle warrior!
@199Xray14 жыл бұрын
@cashstore1 If u haven't already, Try adjusting the clutch assembly by the foot peg. It may to tight and not letting the plates fully engage. Hope you get it sorted out. =)
@ImADoggyw00fw00f11 жыл бұрын
What's the amount of torque needed when installing the springs?
@199Xray14 жыл бұрын
@VVoodstockRider Hahaha. Yes!
@LATAMbiker4 жыл бұрын
Nice job. I've got a 2018 Wee Strom and the innards looked exactly the same. The notches that are on the fiber plates aren't specified to go to the outside, but I guessed that according to the manual drawing they do, if it matters. One friendly suggestion. Get a tripod, or a cameraman with a more stable hand. At times the camera was shaking badly and/or not pointed at what you were doing. Cheers.
@DavidRosaschemist11 жыл бұрын
I have a sv650 2001, and when I start in 1st gear, If I pull too much the accelerator make a noise like a squeal, I think I need replace clutch fibers? I am right, how much cost?>
@dawkinshero203 ай бұрын
Think I messed up somewhere cuz I took the cover off and it looks nothing like that. Now I'm staring at all these pieces and don't know what to do. 😢 Just gonna give up at this point.
@tomificationable11 жыл бұрын
Lol random kitty Kat
@cashstore114 жыл бұрын
I have a dragging clutch on my ducati. I have to go in and take a look. Nothing is cheap when you are buying ducati parts. I need a chipmunk to help me too.
@199Xray14 жыл бұрын
@speedemon103 Haha jus noticed that he says yur youtube name in Chipmunk mode. lolz
@saccaridetriglycide10 жыл бұрын
the entire assembly for the older ones is $208. theres fuck all difference between the two. slight sizing here and there. it would be maybe $100 more worse case. but thats for the full assembly inc. main driven. go geese some oem parts suppliers relevant to your country.
@199Xray14 жыл бұрын
@Wilks89 I think $200 as a matter of fact. lol
@jeepster09345 жыл бұрын
Your camera operator must of od'd on coffee....horrible constant movement. This would of been a good vid and more helpful if camera wasn't constantly jumping around.
Пікірлер: 26
This is hands down one of the best video write ups I've seen on anything pertaining to a motorcycle. Great job man, very articulate and specific and that goes a long way with stuff like this. Ill be using these two videos as a guide as soon as my clutch takes a shit.
Thanks a lot man, going to attempt this myself. this vid still helping people in 2021!
He probably saved himself several hundred bucks in labor cost doing it himself. great stuff.
He doesn't say it, but the factory service manual says 7ft/lbs (10Nm) for torque on the clutch spring set. They do not indicate one for the install of the clutch cover
Excellent! You show that it's much easier than what people think to be. So clutch is kinda like brakes. I always thought it's just two pieces of metals putting together.
thanks bro! this really helped me to replace the clutch con My Vstrom...
@199Xray Thanks for the advice. Normally people assume a modern Ducati. I have a 74 750. It's probably much different than what you are thinking. I checked two adjustments on the outside of the bike. I think I have to go in.
You made this look easy. @4:35, thanks for the Mario Land :)
@keaponlaffin6737
2 жыл бұрын
awesome indeed! 👍👍
change your smoke detector battery every spring
Well done, nice Videos
Nice vid. I have a V-Strom 650 making some funky clutch noise with about 31k miles on it. I was a little concerned about doing it myself but this doesn't look bad at all.
thanks Bike guys nice vid very well did thank you thank you and as for at 7:00 minutes with the cat AWESOME if I wasn't going to subscribe you got me with that One
6:49 thumbs up for the jungle warrior!
@cashstore1 If u haven't already, Try adjusting the clutch assembly by the foot peg. It may to tight and not letting the plates fully engage. Hope you get it sorted out. =)
What's the amount of torque needed when installing the springs?
@VVoodstockRider Hahaha. Yes!
Nice job. I've got a 2018 Wee Strom and the innards looked exactly the same. The notches that are on the fiber plates aren't specified to go to the outside, but I guessed that according to the manual drawing they do, if it matters. One friendly suggestion. Get a tripod, or a cameraman with a more stable hand. At times the camera was shaking badly and/or not pointed at what you were doing. Cheers.
I have a sv650 2001, and when I start in 1st gear, If I pull too much the accelerator make a noise like a squeal, I think I need replace clutch fibers? I am right, how much cost?>
Think I messed up somewhere cuz I took the cover off and it looks nothing like that. Now I'm staring at all these pieces and don't know what to do. 😢 Just gonna give up at this point.
Lol random kitty Kat
I have a dragging clutch on my ducati. I have to go in and take a look. Nothing is cheap when you are buying ducati parts. I need a chipmunk to help me too.
@speedemon103 Haha jus noticed that he says yur youtube name in Chipmunk mode. lolz
the entire assembly for the older ones is $208. theres fuck all difference between the two. slight sizing here and there. it would be maybe $100 more worse case. but thats for the full assembly inc. main driven. go geese some oem parts suppliers relevant to your country.
@Wilks89 I think $200 as a matter of fact. lol
Your camera operator must of od'd on coffee....horrible constant movement. This would of been a good vid and more helpful if camera wasn't constantly jumping around.