LIZARDSKIN | Useful Van Build Material?
Автокөліктер мен көлік құралдары
Hey everyone today we're talking about Lizard Skin. Lizard Skin offers a variety of products but specially we're looking at if they're a good material for sound deadening and insulation. We are giving our honest opinions about this product and how it fares compared to other van build methods.
If you're curious with how we sound deaden and insulate our Vans check out our video on that below:
• HOW TO SOUND DEADEN & ...
We also just launched our Paper Patterns, so if you haven't go check it out!
➡ • Affordable DIY Tool | ...
➡ WEBSITE: avcrig.com 🚐
➡ INSTAGRAM: avcrig.com 📷
Feel free to ask any questions, give the video a like, and subscribe to the channel for more camper van conversion info!
Пікірлер: 33
I love the full disclosure you gave. 😂 Really looking forward to seeing how the temperature gain is affected by that product.
@AVCRIG
Жыл бұрын
Always honest!
Snake oil. That OEM 350 buried in a wall will add to the overall insulating properties, but not by much. Commercially available insulation coatings have values of thermal conductivities in the range of 0.035 to 0.120 W/mK. As one can see from the units, the conductivity is a function of thickness (m), just like every other material. 3M Thinsulate has a thermal conductivity of 0.039 W/mK. What's going to be better, 3 mm of 0.035 W/mK or 38 mm (1.5") of 0.039 W/mK. I know what I'm sticking with! And the best place for any coating with high reflectivity and low emissivity like OEM 350 is on a free surface, inside or outside depending on use case. If a reflective surface does not have a significant gap (20+ mm) in front of it, it is useless. You'd be much better off spraying that stuff on the outside of the van.
@AVCRIG
Жыл бұрын
Funny you mentioned that. We sprayed the roof of our MR crew today with the OEM200 coating. It’s an exterior white thermal reflective coating. Should be an Interesting option.
@videopipeline6419
Жыл бұрын
You are correct hat thin coatings like those shown in this video have minimal resistance to conductive heat flow, making them closer to expensive snake oil than a cost-effective solution. But, re: "Commercially available insulation coatings have values of thermal conductivities in the range of 0.035 to 0.120 W/mK" ...the best *commonly available* commercial insulating materials (PU foams) have thermal conductivity of about have that lower value.
@videopipeline6419
Жыл бұрын
@@AVCRIG Coatings applied to the outside need to have the highest SRI possible. Most boutique products like Lizardskin aren't even rated. Wonder why?
@videopipeline6419
Жыл бұрын
" the best place for any coating with high reflectivity and low emissivity like OEM 350 is on a free surface... You'd be much better off spraying that stuff on the outside of the van." Coatings with the highest Solar Reflective Index have high reflectivity to both visible & infrared, and high infrared emissivity.
@videopipeline6419
Жыл бұрын
re: "snake oil" ...and if AVC actually tested this stuff instead of swallowing the seller's claims, he'd know how (nearly) right you are.
Acoustiblok Blok16 and Blok32 sound isolation material for soundproofing
I'm assuming that if you went with Kilmat & the LS-350, you would apply the Kilmat first. If you used both the LS-300 & LS-350, would it matter which applied first?
@AVCRIG
Жыл бұрын
I was told by Lizard Skin to apply the 300 first then the 350. Sound first heat second.
So it stops the heat but does it work as a vapor barrier as well
This video is a useful resource, that explains SRI, TSER & more: kzread.info/dash/bejne/aaSumbF8Zqeeaco.html Bottom line: if you're going to pay a premium for a coating that has additives, make sure the manufacturer provides independent test results.
@AVCRIG
Жыл бұрын
Great advice. Thanks
@TheSololobo
7 ай бұрын
Impressive product but can it be used in the interior of the van like Lizard Skin, the video showed it on exterior applications only, it would be interesting to see how it would perform on the aluminum cup demo as well.
Are these coatings going to off gas? Also, are you going to spray this in edition to the kilt mat for extra sound deadening? I’m in the process of ordering a van. Will your walls and ceiling work with a Transit crew van? Thanks
@aaron.bailey
Жыл бұрын
Don't get a crew unless you are going to leave the entire front half as is from factory, it's a huge pain in the ass and affects everything from walls, to ceiling to cabinets, etc. If I could do it over I would have just bought an empty van and added the 2 person seat. The airbags also extend past the seat so it limits what you can do behind it (ie, closet etc). Overhead cabinets are also pretty much a no go unless you want to get super creative to extend out past the bags but then you have to figure out how to cover them without harming them. Basically the reason mine is still unfinished.
@AVCRIG
Жыл бұрын
I am not planning to use extra kill mat. The thump test sounds pretty good. We think once we add the 3M thinsulate it will work pretty well as a system. Our kit will work with a crew, but will need editing. We do have crew wall kits coming out soon. HR is ready MR will come soon. We just need to film the install specifics. Just bought a van to get this done.
@roseboudreaux4645
Жыл бұрын
@@AVCRIG Thank you for the info. Love your channel, you are very informative and thorough.
With the lizard skin spray, is it pointless to spray it on the beams that stick out from the van right? Seems like you can save by just spraying it on straight sheet metal? Also do you think it does much to spray it on the floor? I’ll be insulating the van with thinsulate and poli board on the floor
@AVCRIG
Жыл бұрын
I think you’re right that most of the value will come from spraying the main surfaces. The beams will transfer heat into the van, so it’s not a waste in my opinion. I wouldn’t avoid them, but I also wouldn’t worry about going as heavy. In this video we sprayed two products. 1st was sound control, second was thermal. The sound does add value to the floor. I didn’t worry about thermal on the floor though.
@vango1131
Жыл бұрын
Their kit comes with an angled nozzle to get in nooks but spray everything inside and out if u live in hot states and you'll never regret but remember if your just doing inside then it will still be warm inside without a vent
How much product did it take to do the whole van? I am looking at using it for my crew cab pickup and trying to gauge how much I will need.
@cheesygamerz9298
3 ай бұрын
Like 12 gallons
Can it be used externally?
No need to pay a premium price for ordinary roof coating (and have to ship heavy buckets) when you could buy better performers at Home Depot or Lowes. As for the additives, here's one of the most recent developments: kzread.info/dash/bejne/lZV63LuviaS7n5c.html
@AVCRIG
Жыл бұрын
Thanks for the link! We’ll check it out.
is OEM 350 the best they offer? looking for the best solution for the heat in AZ as full timer
@AVCRIG
Жыл бұрын
I think it is. There are exterior coatings, but only in white. Would be a good improvement for the roof of your van.
@tg9388
Жыл бұрын
@@AVCRIG ty, have you tested that yet? I know AZ has some RV roof companies that spray indoors over the factory roof but that's 7k. Any advice? thanks again