Great video! I checked and my current managed switch does not support link aggregation so I just ordered a new one. You're videos have really helped me setup my DS220+ and now I'll have link aggregation set up. All the setup videos and nobody discussed LA, the options, the requirements for the switch to support it. Thanks for sharing!

Thanks for this! I couldn't quite figure out whether I needed to enable LAG on both my switch (Netgear) and Synology. Very concise information. Subscribed!

@SpaceRexWill

4 жыл бұрын

Glad it was helpful!

We love your videos as they are very helpful. You have helped guide us so well when dealing with a RAID config. We just purchased a DS1522+ for our office and are excited to implement for video files. The 10gbe expansion is on its way as they have sold out many places already. Looking forward to the speed (we also have 10gbe cards in PC) we hope to use link aggregation as well as 10gbe but not sure if that is possible. PS. You are the master of the morph cut! I barely notice and we are video pros.

@turbo_bikini

Жыл бұрын

Nice, I have the 1522+ myself. I'm also a content creator, photo, video and graphics. From what Synology told me on the phone, we can link aggregate 4 + one 10GBe ports.

Thanks, I did this using and ASUS RT-AX88U, my options using DSM 6.2.4 were different, but your explinaiton gave me enough information to choose the correct option. It's great that you go into that extra detail of what is going on

@demck85

2 жыл бұрын

This exactly what i wanted to do to pump my 2gbps ATT fiber service into my ASUS RT-AX88U also. So, i'm glad i can find a cheaper solution then to get that going.

Thanks. You cleared up questions I had about how link aggregation works. I was worried that I did something wrong when I couldn't get better than 1 Gb/sec between the NAS and my computer. Looks like I have it set up correctly.

Awesome.. Exactly what I needed to take the advantage of Link aggregation. And what it is. I am subscribed to your channel. Thank You. 🙏

@SpaceRexWill

2 жыл бұрын

Glad you like the content!

Thanks for this video! Very helpful!

@SpaceRexWill

3 жыл бұрын

Glad it was helpful!

Awesome vid bro

Big help with my LAG. Thanks!

thank you!

Thanks for the detailed explanations on all points. I have a DS1815+ and a Ubiquiti 48 port 1gb switch and I was able to get both configured to create the Bond 1 and the IEEE802.3ad Dynamic Link Aggregation. Before I just had 4 - 1gb cables connected to the switch. With both the bonding of the 4 - 1gb ports and setting up the Ubiquiti switch I should see better throughput. Now I am off to see if I am getting the better throughput I expect. thanks again..

@SpaceRexWill

4 жыл бұрын

It’s going to help a ton if you have multiple people trying to connect! Another thing to check out is jumbo packets

@jimholloway1785

4 жыл бұрын

@@SpaceRexWill I noticed that you did not set the MTU speed but it was grayed out saying MTU 2000, would you suggest MUT4000 or 5000 or all the way to MTU9000 with four 1gb connects in the Bond? Currently I have it set to MTU 5000 and I am going to do some testing today.

@SpaceRexWill

4 жыл бұрын

First of all make sure everything that your connection goes through will allow jumbo packets. If there is a single switch that doesn’t it will creat a huge bottle neck (clients don’t all have to have it). If everything can have jumbo I would test it out. I just 9000 (standard for jumbo) and for sequential reads / writes over SMB with my 10 G connection I was getting around 20% faster transfer rates. I think a big part was the SAMBA bottleneck

@jimholloway1785

4 жыл бұрын

@@SpaceRexWill I just set the bond 1 to MTU 9000 and will try it out. thanks for the quick reply.

I know this is an old video but I just got the ds220+ and it's a little different. @ the 5:36 area I don't get the choice to select connections. It goes straight to the manual up part, which that part is requesting more info like vlan info etc. I don't have a vlan set up. Not sure how to proceed from here because it won't let you

Thank you sir.

Thanks and easy tutorial, I have Netgear jgs524 and a DS920+ and every setting worked BUT when I connect the second LAN cable, I can connect internaly to the DSM but the DS cant connect to the internet.

I have a new Synology ds224 NAS and exactly the same Netgear GS110EMX but I cannot get the LAG to enable in LACP mode, but when I change type to Static mode it works. Why?

You described Balance SMB and go on to use and set up the Balance TCP option but the first option (B. SMB) does it require a smart managed switch? Or are there simply no options with unmanaged switches.

Thanks mate.

@SpaceRexWill

4 жыл бұрын

You're welcome!

Hi @SpaceRex! Something I don't understand is how I am supposed to link my Router, in my case the FRITZ!Box 6690 Cable, with the switch. If my router supports fir instance only 1Gb connection, then I will have a bottleneck from the router side, no?

@SingularityFM 25 minutes ago I just bought a Synology DS 723+, and I don't have a switch. I followed your instructions but used the automated version for creating a bond and took a chance to implement it by connecting both my Gigabit cables to the router I have from Bell Canada. It seems that everything went fine, and the good news is I didn't get locked out of my NAS ;-) The interesting thing, however, is that my browser auto-refreshed when I implemented the bonding, and now I am getting a warning that connection to the NAS is "not secure" and Chrome is showing the https in red with a strike through. Should I be worried that somehow my NAS is now insecure and "went public" on the entire internet so anyone can highjack it?

This is a helpful video, so I have an unmanaged switch DGS 1016A, that supports link aggregation but after the setup process I get "Failed To Establish IEEE 802.3 ad connection" under the network status area. Everything still works; I can access the NAS and its content, but I get that message, does that mean link aggregation is not configured? What do you recommend?

Do link aggregate doubt the speed if we disconnect lapto?

Good Tutorial. What if in "Balance-SLB" mode. How fast of speed if we do two or more Lans in test [without "Dynamic Link Aggregation" set] The maximun speed is 1Gbps or more?

But the speed dropped from 108Mb/s to 23MB/s - did it go back up to 100 Mb/s?

Great Video!, I need to play around with this. What do you do for the IP addresses for each NIC?, Dynamic on all 4 or Static on 3 and one Dynamic? - I'm always concerned with dynamic IPs within the scope of DHCP.

@SpaceRexWill

Жыл бұрын

So once you use LAG (any of them) you only get a single IP per bond

@NAY2GAS

Жыл бұрын

@@SpaceRexWill But the IP is best used as static and outside of the DHCP Scope?

Love your videos! Would love to see you make video on virtual machine manager installing windows 10

@SpaceRexWill

4 жыл бұрын

Haha well I would love to do that too, but windows licenses are SO expensive!

@derkaderkamohamadallaackbarnut

4 жыл бұрын

@@SpaceRexWill Ebay. 5-15$ a pro key. That is how I do my VMs

Cheapest managed switch compatible with DS1019+ ? Need to do link aggregation

I tried this on my DS1819+. I have 4 different modes for link aggregation and they have different names. I am running DSM 6.2.4-25556 Which mode is the best? I don't understand the difference except when the switch forces you to make some modes unavailable (since the switch doesn't support link aggregation LACP, for instance).

@SpaceRexWill

3 жыл бұрын

Balance-TCP - Best, requires your switch to support it though Balance-SLB - is unable to react to changing traffic flows, just puts even connections on each port, second best, does not require anything special on the switch active / backup, used for fail over only, does not speed up many simulations connections

Great video. I have an 1817+ but all my client connections are over wifi via my router and gigabit switch so i assume I wouldn't gain from this?

@SpaceRexWill

4 жыл бұрын

This is most likely true unless you have a mesh system that you could have a gigabit connection going to each router. If you have the hardware its not a bad idea to at least enable link failover just in case a port dies your NAS would not skip a beat. Edit: Now that I am thinking about it, if you router supports link aggregation you could get increased performance if you find yourself connecting remotely back to your Synology as you would basically have one lane for your web traffic and one lan for you Wifi a lot of 5GHz routers actually have throughput greater than 1 Gb/t if you also combine in the 2.4 GHz range

Awesome video👍 I'm new at this so maybe silly question. Is it possible to have 2 external IP addresses. One that route the traffic through a third party VPN server subscription like "ekspres VPN" and another routing traffic through ISP IP address?

@SpaceRexWill

2 жыл бұрын

There is no way to do this through DSM

So...impossible to get a 2gbe connection to a single pc? Dual nic cant make it work? What about to a truenas device? Got 40tb of data to copy from old nas to new. 2gbe would cut times in half.

Thanks for this vid. It would be completely awesome if you could add some links from which we could get these switches that support 802.3ad. Thanks again.

Great video, thank you. Will we be able to bond all 4 network interface for a link aggregation?, instead of 2

@SpaceRexWill

3 жыл бұрын

Yes! You can generally do up to 8 I believe based on the standard

@solaris7219

3 жыл бұрын

Thank you 🙏

Hello, Thank you for this video, but i have a question, could we make that with 4 lan ports?

@SpaceRexWill

4 жыл бұрын

Yes completely! The standard allows for up to 8 cables to be connected, though do check your switch as some of them have lower than this

@Jololoriol

4 жыл бұрын

@@SpaceRexWill Thanks a lot.

Does the 8 Port switch linked on Amazon (GS308T) support link aggregation? I purchased a different Smart Plus Netgear switch that showed it support LAG (GS108PE) but alias only the 16 Port and up support LAG in this series. Thanks

@petersonfamily6223

3 жыл бұрын

Purchased and confirmed it does support LAG. The software is more robust and there are many more options available now but got it to work on a new DS1520+ using all four LAN port for a Network Status of 4000 Mbps, Full Duplex, MTU 9000

On my NAS I enabled Link Aggregation, I haven't touched my switch but If I removed one cable the NAS keeps on pinging. I don't know though if I am getting any better throughput. If I turn LAG on on the netgear the pings all stop. From my netgear I have Static disabled (LACP) my lag has different options like Hash mode (eg 3 Src/Dest MAC, VLAN, EType, incoming port). Any suggestions?

@SpaceRexWill

4 жыл бұрын

So there are really two types of link aggregation. "Dynamic" (sometimes named; balance TCP, Active, 802.3ad) and "passive" (synology calls balance SLB). If your switch does not enable Dynamic LACP do the passive one. You will still get failover and better multi user performance (though it does not balance the actual loads) without having to enable it on your switch

Hey, great video. I would appreciate knowing how to connect my computer/laptop to the network to take full advantage link aggregation. Does that mean that my laptop also needs to have two Ethernet ports?

@SpaceRexWill

Жыл бұрын

You cannot get faster than 1GbE using LACP to a SINGLE computer. You would only get the speeds if you had 2 computers accessing the NAS

Active backup mode just trying to think like it SPP or just wait for the link to die to turn the other one on interesting features but I’m a stick with the SMB three

Is this usable for home use? Like is a switch required? Sorry for the noob question, never had a NAS. My wife will do some video editing, just for home use. The rest will be for backup purposes

@SpaceRexWill

3 жыл бұрын

What I would do if you don’t want to use a switch is this: (works with 1gbe) kzread.info/dash/bejne/ZHeNj6ingdnbddY.html You could connect both your wife’s computer, your computer and your router (so you still get WiFi) directly to the NAS

Can you use link aggregaron with any switch?

What do you do if you apply Dynamic Link Agg and realized your switch is Unmanaged, loosing connection to the Synology? Hit the Synology Reset button?

@SpaceRexWill

2 жыл бұрын

Just plug in one port and it should hopefully work

When there is a Synology NAS connected to the switch by two 1GBit aggregated links and one PC with 10GBit, can these two devices communicate in 2GBit?

@SpaceRexWill

4 жыл бұрын

Any single device will only be able to get 1 Gbit so no

I have a question that i cannot find... its been a long time since ive been in a house with cat wiring through a house, i'm about to move into a new built house that has the cat wiring throughout the house to wired internet connection. I've never had a router that has port aggregation on it... can i still use the ports that are labeled aggregation as normal ports as long as aggregation is not enabled? Because I would probably need to hook up at least 5 to 6 ports. I'm looking at the Netgear CAX30 nighthawk...

@SpaceRexWill

3 жыл бұрын

Yes completely! This is just an extra feature that you can enable if you really need extra speed when you have a bunch of users connecting.

@ripkaylizzle2170

3 жыл бұрын

@@SpaceRexWill thank you so much for the reply I really appreciate it because so many people don't reply to questions left on their videos even if the video was posted very recently so again thank you so much

Would it help if the PC was connected over 10GB LAN to the switch, or would that not profit from this?

@SpaceRexWill

4 жыл бұрын

Sadly not. Dynamic link aggregation acts just like a GPS. It will always send you down the least busy route. But it will not send packets down two cables going to the same destination at the same time as this could easily get corrupted

So you need a modem that supports link aggregation, or will managed smart switch be enough?

@SpaceRexWill

3 жыл бұрын

Switch is all you need!

@user-vj4ih9pp9z

3 жыл бұрын

@@SpaceRexWill Thank you. I picked up GS308T from Netgear. It was in your description. Hope the transferring speeds get a bit better.

I just ordered a DS1621XS+, (6) Synology 8TB drives, and (2) Synology M.2 cache drives. If I install another 10Gb NIC in the PCI Express slot giving me a total or (4) 10Gb NICs, is it possible to setup two different LAGs and then setup load balancing between the two LAGs? Ideally I would like to have two 20Gb LAGs each going to a different UniFi switch. Thanks!

@SpaceRexWill

2 жыл бұрын

Hmmm I don’t think so. You could do a single bond with all 4 (using passive aggregation) or LACP on two different subnets

@virtualguitars

2 жыл бұрын

@@SpaceRexWill Thanks man. I wanted to have some fault tolerance between my two core UniFi switches. As the primary user of the system, a LAG really isn’t going to provide any noticeable speed advantages anyway, so I’ll just setup it up for a little balancing without the LAG. Thanks again.

What would be my IP address to fill in? Where do i find it?

Hey, very informative video. Thanks man. But I do have a question here. I connect two NICs to my switch. My switch does not support link aggregation natively. So I had to use Synology's built in "link aggregation". So I bond the two NICs. But the problem is I also have a OpenVPN server running on my Synology NAS. And I need to set port forwarding on my router. Since Synology was connected by two wired connection with different two MAC addresses. The router will have two different MAC address who share a same IP address. So the port forwarding rules, sometimes would fail. And I would have to delete the forwarding in router, check which NIC is connecting to the router, and set up forwarding once again. Do you have any idea to solve this issue. I would prefer not to buy another managed switch that support link aggregation natively. Currently, I'm doing a alternaive solution, is to seperate the IP address. And I manually set one IP to my main working station, the other one to the Backup server. This is tedious. Kinda dodge the problem, but cannot solve that forever. Besides, since the router sometimes confused which MAC address should have the ip. My DDNS server on Synology fail and resume over and over again. Any idea? Appreciate the help if you have any suggestions.

@SpaceRexWill

3 жыл бұрын

You should be able to setup port forwarding with a specific IP address on your router. Otherwise it might be worth it for you just not to use link aggregation, depending on your needs. I have found that sometimes it is more of a pain then it is worth

@looper6120

3 жыл бұрын

@@SpaceRexWill thank you. Is there a way or is there a router that allows me to setup port forwarding using ip address plus MAC address?

Should i copy 1 file with SMB to Laptop over Wifi 6 4800mbps with real copy speed is over 200mb/s?

@SpaceRexWill

2 жыл бұрын

WiFi always slows your network speed

I've used one of the NETGEAR switches with not good results. Specifically, the NETGEAR 8-Port Gigabit Ethernet Smart Switch (GS108T) It worked great initially, but after 3 days it started to shutdown the ports' connectivity (eventhough all green lights were on! Has anybody else experienced this? What switch would you recommend with IEEE 802.3ad capabilities? Thanks!

@SpaceRexWill

2 жыл бұрын

Weird. You may have just gotten a Lemmon. Of switches I have used net gears tend to be the most reliable. They have rough user interfaces but generally work quite dependably

Question. My Synology router (Rt2600) doesn’t do LAN link aggregation. I’m running a mesh network (wireless). I just purchased a Synology NAS with aggregation plus the smart managed Netgear switch. Will it improve things still? Will remote access speeds also be more robust? I only have one computer hard wired but its not a primary. Thanks!

@SpaceRexWill

4 жыл бұрын

Unless you are saturating the gigabit connection AND have multiple users connected the only thing that this will help is the one case where a cable / port fails

@epg2501

4 жыл бұрын

SpaceRex Even with remote connections/big file downloads remote?

@SpaceRexWill

4 жыл бұрын

You would need really fast internet (gigabit) and be working on the NAS locally to really see any difference

Can you link more than two ports? IE, 4 ports on the router to 4 ports on the NAS?

@SpaceRexWill

2 жыл бұрын

It is up to 8 but most people will not get an advantage past 2 or 3

@VoteRepublicanSaveAmerica

2 жыл бұрын

@@SpaceRexWill Thank you

I have seen a video from NAS compares / Span dot com where they actually tested a similar setup with a LAG of 4 cables vs single 10Gbe and the results of that were shocking The client only had a 10Gbe NIC and he got close to 400 MBps over the LAG According to your explanation this should not be possible so I am wondering if you could explain how they were able to do that They used a DS2419+ and a Netgear smart switch for this

@SpaceRexWill

4 жыл бұрын

So as I said in the video this is possible using SMB Multichannel, but it is currently still in dev for linux systems. You can go through terminal and enable the settings, however it is unstable and you can get corrupt data stored in your NAS from this. I would not recommend it for anyone other than to say "hey look its possible" as there is a good chance your data will get corrupt

Can you set up LAG with unmanaged switch @spacerex?

@SpaceRexWill

2 жыл бұрын

You can do the passive lag, not active.

I was hoping you would talk about VLANs and how to configure them on Synology

Not all Netgear smart managed switches support link aggregation. My core switch is a GS308T which does support it, and it works fine with a Synology NAS. I have two different models of edge switch, one is the GS305E and the other is a PoE switch which I cannot remember the model of. Neither of these supports link aggregation. The ‘E’ switch supports Vlans, QoS, loop detection and can display statistics and do a simple cable test, but not much more. The ‘T’ series switch can do just about anything that you would expect a layer 2 switch to do. It cost be about 40 GBP with a discount, I think it’s about 50 normally. Had it for about six months and no problems with it. No 10Gb, but I don’t need that.

Hey I am planning to buy DS 918+. Can you suggest economic 8 port Link aggregation switch without POE? I am tight on budget. Thanks.

@SpaceRexWill

4 жыл бұрын

Looks like probably the best bet is this: amzn.to/2XlGodv though if anyone else has a better one let me know!

@JayantBB78

4 жыл бұрын

@@SpaceRexWill Thanks dear. Netgear GS308T is not available in India. What about TP-Link TL-SG108E V4 8-Port Gigabit Easy Smart Switch. www.tp-link.com/in/business-networking/easy-smart-switch/tl-sg108e/#overview Will it work with Synology NAS LAG?

@SpaceRexWill

4 жыл бұрын

You need at least a “smart managed” switch from Netgear to do dynamic LAG (load balances the connections) (Also some models with smart managed might still not) you could still use the balance SLB with any switch. It will just balance the total number of connections across the two ports (basically every time someone connects to the synology it gives their connection to the port with the fewest connections, not regarding how much traffic)

@JayantBB78

4 жыл бұрын

@@SpaceRexWill Thanks buddy for your help. My concepts are little more clear now. TP-Link TL-SG108E V4 8-Port Gigabit Easy Smart Switch has *Static Link Aggregation* as software feature, which I am not sure will work with Synology or not.

you are super.

@SpaceRexWill

3 жыл бұрын

Hey thanks!

Thank you for the easy follow video but I need help even further. Ive brought a Terramaster F5-421 and Xyxel GS1900-10hp and followed your video but soon as I turn on LACP on Switch My TNAS -PC cannot find any i.p address to login into. Any ideas . Thanks again

@SpaceRexWill

4 жыл бұрын

Which did you do first enable it in DSM or your switch? It is a little finicky sometimes

@lefty0184

4 жыл бұрын

@@SpaceRexWill thanks for getting back to me. I did the Terramaster first then the switch . I tired after I reset everything by switching them off and tired the switch first then the NAS , same nothing again.

@SpaceRexWill

4 жыл бұрын

Try having only one cable plugged in but set up dynamic link agg on both ports.

@lefty0184

4 жыл бұрын

@@SpaceRexWill OK will do and I will let you know. Once again thank you

@lefty0184

4 жыл бұрын

@@SpaceRexWillSorry for the late reply. I did the switch first and I cannot see the Nas or cannot log into the switch default ip address until i remove the network cables from NAS into the switch.

FYI Synology does support SMB Multichannel, you just need to enable it in smb.conf

@SpaceRexWill

4 жыл бұрын

SMB Multichannel is still experimental in SAMBA. You should not use this in a production environment as it has been led to data corruption from mismatched packets

Little mistake its not the "smart managed plus" seires of netgear devices (E on the end) its the "smart managed pro" series of devices (T on the end) that have link aggregation.

@SpaceRexWill

3 жыл бұрын

The smart managed plus switches with at least 8 ports support LACP

@grahamjones6712

3 жыл бұрын

@@SpaceRexWill well i bought a GS308E which is a smart managed plus device and it doesnt have the "Switching" tab in its webui that contains the LAG options it only seems to have vlan options product data sheet has "no" next to link aggregation in features www.netgear.com/images/datasheet/switches/GS305E_GS308E_DS.pdf dissapointing because nascompares.com website told me this was one of the cheapest switches with link aggegation which is false.

I have SMB enables and configured on my old TS 419 and it works incredibly well all the way through to my PC running windows 11, link aggregation requires so much you really benefit the multi file transfer into multiple machines even on the net work it’s just not worth it it’s just better to throw all the data as fast as you can out and being that you can use Smb3 with normal off-the-shelf switches the benefits and the costTruly make it the way to go because you get the redundancy out of it so where is the problem,

“apparatuses” :)

I was expecting you to rip the cord out bro 8:38.

@SpaceRexWill

4 жыл бұрын

Sorry to disappoint 😂

none of your equipment links link to any of the network equipment you are talking about in your video.

@SpaceRexWill

4 жыл бұрын

This was the switch I was using kzread.info/dash/bejne/haan1KiQaaSsl9Y.html

USB 3.0 on NAS with USB-Networkadapter give you 5Gbit/s

@SpaceRexWill

3 жыл бұрын

I have been meaning to make a video on this, but the comparability is fuzzy. What mode do you have working?

@MCSanych

3 жыл бұрын

@@SpaceRexWill you need to install a special driverpack. Just google this

0:50 omg, is this editing on purpose?

@johnnyyipkk

2 жыл бұрын

9:34 I really think that person on screen is a fake man, his voice sounds abnormal in some way as well.

I don't know why I am watching this. My cheap Synology has 1 port.

Your up-talking is very irritating.