Linear Bearing
Ғылым және технология
I want to show you the guides for an angle grinder that allows you to cut wide steel. In the basic versiune, I use it for an angle grinder, but it can be used for various tools, eg Plasma, circular saw. Preaсe watch the video, likes and subscribe!
Thank you! And I can't wait to show you whats next!
Пікірлер: 52
I like this design. It is simpler than others I have seen, requiring fewer bearings, yet it is strong. I also like that it requires adjustment in only one axis and that the bearings are somewhat protected from splatter/grinding debri.
Great build, lots of potential uses.
Just think how nice and quiet that would be if all was ground straight and parallel. Good job with the fabrication!
А практическое применение какое?
Отличная надёжная, жёсткая каретка без люфтов и с лёгким ходом. Но есть очень серьёзная недоработка. Каретка охватывает направляющую со всех сторон и нет никакой возможности усилить рельсы, прикрутив их к прочному основанию или добавив косынки либо раскосины.
@gor-yu2me
Жыл бұрын
Не надо там ничего усиливать,для чего?
@user-lm8yn9rp4h
Жыл бұрын
@@gor-yu2me Такая даже полуметровая рельса гнётся как макаронина от малейшей нагрузки.
@gor-yu2me
Жыл бұрын
@@user-lm8yn9rp4hхватит пустомелить,я работаю с таким материалом, и на 50см ты даже 20 на 20 трубу не прогнешь со стенкой в 3мм. А макароны ты лучше кушай,а ни вешай тут ...ок?
@user-yj7cr6vo4i
Жыл бұрын
А ещё вспомнить что зимой снег накатает ... сомнительная конструкция , сомнительная ... хотя сделана достаточно качественно
@kaper1979
Жыл бұрын
Ролики из трубы , ещё и на болтах вместо втулок , от куда там отсутствие люфта
Hey, good job 👍 Thanks for sharing 🙂👏👏
It's a very good creative work I like this video thanks for sharing
Excellent , I want more ideas , thanks.
I love it!
Već dugo radim ovakve stvari i nisam vidio nikad ništa bolje a jednostavno za napraviti.kapa do poda bravo
@gor-yu2me
Жыл бұрын
Это точно, особенно понравилась идея с поворотом направляющей вокруг своей оси
How will you give support to the angle iron rail on which this roller assembly is made to run? You can only make it for short span only.
@gor-yu2me
Жыл бұрын
Зачем его поддерживать???!!! Ты его не согнешь и на 1мм!!! Посмотри каким ребром он работает этот уголок
Very good idea
Bravo........roller bearing.......cheers
very very nice thank you very much for sharing this video thanks 👍👍👍
@severinomanoelsantos5438
Жыл бұрын
Great job from são Paulo Brazil
nice mechanism, I saw a similar setup mounted in a cargo van to the roof, for loading
Хорошее испрлнение для короткого хода каретки.
Qualquer a identificação desse rolamento?
Very good video. How come your first video has so many views please tell me.
Very very clever.!!!!!
Interesante, pero para que sirve o en que se usa
@joeray088
Жыл бұрын
¡ si supieras todas las aplicaciones que tiene !
E la guida come si fissa? Se si chiude tutto il "carrello" non c'è modo di fissare la guida da nessuna parte. Giusto?
Надёжно но непроктично зимой. Работать не будет
@gor-yu2me
Жыл бұрын
Ты его зимой где собрался ставить???? Человек под открытым небом сам работать не будет,если не идиот
@user-yj7cr6vo4i
Жыл бұрын
@@gor-yu2me кто в лес , а кто по дрова .... тебе говорят что зимой снег накатает , и клинить будет ... вариант только для южных районов
You need to remove 4 nuts under flat 2 bearing plate and put coil springs on 4 bolts before fixing 4 nuts.
Liked the whole assembly except for welding the bolts. IMO some CA glue would've been all that's needed with no heat distortion and easier bearing changes in the future.
Eso no funciona para trayectos largos por las ruedas que le colocaste abajo, como sostienes el riel.
@joeray088
Жыл бұрын
¿¡ Ilumínanos maestro con un ejemplo !?
It's not linear bearings... It's just cylindrical bearings that rolls on a metal line...........
Рабочая длина пару метров. Конечно зависит от веса нагрузки. Потому что уголок- рельс ,в данном случае,крепится только на концах.
@gor-yu2me
Жыл бұрын
Вес нагрузки вес ушм +узел маятника и неужели этот минимум согнет этот уголок усиленный полосой?
Does anyone have a link to those rollers for purchase?
@flaviotorres3370
11 ай бұрын
Encontrou o link dos rolamentos?
Бесполезная вещь
@MyFluffyClouds
Жыл бұрын
It's called art
Дорогая и бесполезная вещ.
Зачем
If you could use that technology to build train wheels, you can save a lot of energy i guess. 👍👍👍👍
@srinivassiddarth
Жыл бұрын
Because it reduces the direct weight of the train on the wheels and gravity. 🙏🙏🙏
@gor-yu2me
Жыл бұрын
@@srinivassiddarth каким образом уменьшается вес на колеса,если гравитация всеравно давит вниз и на рельс?