Best off road KZread channel!

i just got these shipped to me and i go in for an alignment on the 20th. Stoked to get them on.

Thank you, I've been waiting for this follow-up since you mentioned the bolts and showed a glimpse in the bumper video. BTW, installed the eBay Tacoma bumper on a customers 4Runner and he was very happy. Thank you for those vids as well. Keep it up and the channel will continue to grow.

@DirtComplex

3 жыл бұрын

That's awesome! I'm glad we are able to help! Thank you for watching our videos and especially for the encouraging words.

Great demonstration, finally somebody that knows how to highlight a product that actually works and saves time and money. I was really getting tired of alignments after any offroading and these are a great idea whether you offroad or not.

What a great explanation

Heck yeah bro finally a new video!!!

@DirtComplex

3 жыл бұрын

Thanks! We've been so busy trying to get the 1970 Buick GSX ready for the show. I still owe you some hats and stuff!

@jaymoar3561

3 жыл бұрын

Dirt Complex bro stop worrying about that it’s fine! Just keep making videos brotha!

Awesome! TYVM

Awesome review!

@DirtComplex

3 жыл бұрын

Much Appreciated!

@harrisonortis7851

3 жыл бұрын

Heck yeah!!

I have a 2003 sequoia and had to cut the control arms out. I have been hunting a popping noise on cornering and turning ever since the install. I used the old cam bolts without the sleeve and think you may have solved my problem. Thank you.

Can i run this with the Marlin crawler gussets? Or is it not necessary?

I do not have these bolts but I've replaced bushings. Is it possible to get alignment specs for camber and caster and adjust c bolts to the correct specs that way?

My truck hit the curb since than it pulls to right ( same side lower control arm hit ) I did the wheel alignment but still no change. Do you think the camber bolt is out of the position. I asked them they said it got nothing to do with that and all the spec looks good on result. I still feel the pulls.

When will u folks have these instock for a 2nd gen tacoma?

Question how or what would be the best way to adjust this stop cams for alignment? I couldnt get a good alignment with the stock cams because my bushing needed to be replaced and the bolts needed to be cut so I bought this to replace the stock one

If I do a lift thats only 1.5 inches .can i still use the stock uca and cam bolt etc and get a good aligbment or is it gonna be kinda off?

I don’t see any cam bolts for the 5th gen 4runner on your website!

Go with alignment tab kit from either dirt king or total chaos with this kit. Otherwise, you will bend your stock alignment tabs.

I'm not seeing these for a 4th gen 4runner... do they make them?

can i use this with spc upper control arm? thanks

Will these work on a 2005 base tacoma?

You didn't have to disconnect anything to relieve pressure?

Hey man lml you think this kit could fit a 96 toyota t100?

will these work on a Toyota Landcruiser 200 series?

I really need to get a set for my 02 toyota tundra sr5 4.7 2.5 lift but how do I obtain these

What do you torque these to?

what material is used for both sets of bolts?

I need these for my 2016 tacoma 4x4 ....Whats up.?????

What causes bumpsteer on lifted trucks ?

Why would I need caster bolts angle set at max outboard

Do both side go the same lines? Per haps say 3:00?

Will it work for a 2010 toyota tundra 5.7 ??

Got any for the 4th Gen 4runner? Didn't see them on your site?

@DirtComplex

3 жыл бұрын

I will contact Bison Offroad tomorrow to see if he can get them up on the website. Thank you for watching!

Will these work with 07 FJ's? Didn't see them on there site.

@DirtComplex

3 жыл бұрын

Hey thanks for watching! Yes, the kit # TC-1502 for the 03-09 4runner and 05-15 Tacoma will fit your 07 FJ.

So with a 2.5 inch lift it’s best to go with maximum caster? So should I tell the alignment shop to go maximum caster then adjust rest of alignment?

@DirtComplex

3 жыл бұрын

Yes. It will help with steering feel and also rubbing!

@scottycombs3974

2 жыл бұрын

@@DirtComplex if you run bigger tires it gives more room to rear of tire. rubbing rear of tire to body and plastic and causing possible damage slicing tire

why should you run max caster? is this so you will not wheel rub the backside of tire? also you are so f-ing correct tech will not notice and will not adjust. I had this happen to me. tech had one caster in on one side and out on other, one side rubbed and other was fine. so I made adjustment.

I’ve been aligning vehicles for a while. both bolts adjust camber and caster depending in which direction you move them or I’m I right🙂

@DirtComplex

Жыл бұрын

Yeah if you have the proper upper control arms then you can compensate enough camber adjustment with the front lower bolts to get it back where you need the camber

Where are these!!!!!

Is anti seize good to put on the brass parts? So it doesn’t seize again

@josemarquez86

3 жыл бұрын

What brass? Its Yellow chromate come on young buck!🤦‍♂️

@krazy4pb

3 жыл бұрын

@@josemarquez86 so is anti seize okay? Or should I use grease for like bushings/ball joints?

@josemarquez86

3 жыл бұрын

@@krazy4pb Depends. You can use both. if you live in the South like myself or West (Cail whatever) but if live in rust belt area use anti-seize.🤙

please get rid of the music after the intro

Not really the best video ive seen. He left out an important piece of info. You can definitely run these on opposite locations to move your tire away from the rear of the front fender. Its called adjustable upper control arms buddy.

Total chaos LCA cam tab gussets are a much better solution for the same application. They offer unlimited adjustments as opposed to the stepped adjustments from Bison. Sorry, not sorry. Back to the drawing board for you bison.

hate music in a video

Stay away from these

@jeremiahhilter190

5 ай бұрын

Any reason why?

I have 2003 Toyota Sequoia.. the tundra ones fit?????