Друзья, добрый день. Меня зовут Павел. Я обращаюсь к российским зрителям этого канала. Судя по статистике ролик про изготовление безтопливного генератора Тип1 посмотрели уже 11 миллионов раз. И я думаю, что часть аудитории попробовала повторить данную установку. Может у кого-то даже получилось, а у кого-то нет. Но я уверен, что люди попробовали. И я попробовал тоже. Здесь я хочу поделиться результатами моих испытаний. Теперь про генератор. Долго пытался найти генератор 24В на 200А, не получилось, искал среди б/у и ремонтных агрегатов. Нашёл генератор на 120А и дальше работал с ним. Спилил "зубья" на роторе аккуратно токарным станком, отлично получилось. Далее - ниодимовые магниты 20х20х10мм. Приклеил 12 магнитов к 12ти полюсам на роторе Полярность чередовал, как в видео, проверял её на компасе. Далее: опалубка из пластиковой бутылки и эпоксидная смола. Всё как в видео. После заливки ротор был обработан на токарном станке для выравнивания цилиндрической поверхности. Важный нюанс: в моем исходном авто-генераторе у обмоток статора - не три, а 4 (Четыре) вывода обмоток. С помощью тестера определили "0" и "фазы". Далее собрали генератор и запустили на стенде. Слава богу есть специальный стенд для проверки автогенераторов на работоспособность, поэтому не пришлось покупать движок для испытаний и мастерить основу-подставку, как в ролике. Результаты испытаний: при скорости вращения генератора 3000 об/мин модернизированный генератор выдал напряжение переменное на выводе "ноль-фаза" - 25В; на выводе "фаза-фаза" - 40В. К расчётным 230В даже не приблизилось. И очень сильная вибрация, тяжелый стенд заметно вибрировал. Вот такие дела. Хочу посоветоваться с теми, кто уже проходил этот этап. А также я хочу организовать сообщество людей (Человеков), которые хотят развивать безтопливные технологии на благо Человечества. Может слишком пафосно, но таков мой посыл, кому близко - отзовитесь). И вообще, хочу вынести обсуждение данной проблематики на широкий простор. Я думаю, что уже хватит нам отсиживаться по своим "норам".. Пора объединяться! Все кому в душе отзовется мой призыв, добро пожаловать, пишите в личку или здесь в комментах. Я размещу это сообщение в комментариях к разным роликам на этом канале, надеюсь, что буду услышан. Всем добра! Павел.

@lutyiua

Жыл бұрын

Эх Пашка Пашка как думаешь как много может вместить корпус данного Эл мотора?))) Например, мотор поменьше с аккумулятором и схемой может? чтоб болванку аллюмиевую крутить)))

If it were truly free energy: 1- It would be on all major media networks 2- The creator would be the announced next Nobel prize recipient 3- Oil prices would immediately drop significantly. Not going to tell you what to believe, just throwing out some reality.

@johnwayne9103

8 ай бұрын

Wrong! The history shows, that the creator will be visited and get an offer or a request to stop any further efforts in this topic. Or something bad might happen to his family… Sometimes the creator will vanish without any traces… If you'll do some research, you'll understand.

@arnoldbailey7550

8 ай бұрын

@@johnwayne9103 If the creators had a legitimate working device, in the US, when they apply for a patent and demonstrate a working device, the government will claim national security and pay the creators a "fair market" value and they must sign a non disclosure. However, if the creators publish it on social media, the government cannot claim national security. You can look up patents under national security and social media or public introduction and use.

Why are you people being assholes? They made a cool machine. It's a prototype I'm sure they will go bigger and better eventually. Well done!

Стараетесь спасти матушку Землю.Спасибо вам ребят.

I have theorized. That what you have done is possible. Even made a few small scale attempts myself. Needed some machining equipment. That I did not have or the expertise to metal work. You basically created a rotating magnetic field or switching fields. Very ingenious. Is not perpetual motion. Always knew magnets was stored energy, Just never could figure out how to convert to usable energy. Well done! Fellows.

@dgfgdsfds4128

Жыл бұрын

Unfortunately, even magnets "wear out" over time, i.e. the magnetic field is depleted and becomes weaker

@14312KIDS

Жыл бұрын

@@dgfgdsfds4128 After the energy is depleted from a magnet. It must be replaced. But since the scientific world. Will not except magnetism as a form of renewable energy. They scoff at any idea of using natural magnets for power generation. Calling it perpetual motion. When it is no different than petroleum products. Naturally produced by the earth itself. Just have to discover how to convert to a usable form of energy.

@bahodirjonabdullayev7011

Жыл бұрын

Of course, a magnet weakens over time, which type of magnet do you think stays the same?

@14312KIDS

Жыл бұрын

@@bahodirjonabdullayev7011 None stay the same. Except an electro magnet. Which requires energy to maintain a magnetic field. Man made magnets last longer. Natural magnets are made by the magnetic field of the earth. But have a short life.

Thanking to your "Great" effort that you shared with humans. Amazing stuff.

You can see a cut on 9:00, the wheel is starting to slow down, but after the cut is spins fast again, so you spinned up the wheel again.

@johnstepho3122

Жыл бұрын

Good eyes. Nicely done.

@lazar.vision

10 ай бұрын

exactly. thanks

One of the excellent inventions God bless this project Well done. This was the dream of mankiind

@pankajandfateh9125

Жыл бұрын

I would like to sell it to all possible in India. 😊

@KevinSmith-os5yz

Жыл бұрын

Yep, everyone wants energy at zero cost. Unfortunately not possible. Too bad thus guy is just scamming everyone for youtube clicks:)

The dramatic music makes it so believable too!

@jazzzzdude

Жыл бұрын

i didn't notice his hands jump to a completely different position after removing the batteries, at all.

Excelente Video Gracias por compartir

@HiddenTechnology_

Жыл бұрын

Gracias por tu apoyo

Viel Erfolg von der Lichten Seite!

AWESOME

Where can I get a full circuit diagram of this? And why an Aluminium Silver alloy you have chosen for the rotor?

Grandioso complimenti

Génial 😊😊😊

Tuyệt vời. cám ơn đã tiết kiệm đc: kính phí, thời gian. Sư phụ.

It would be useful to measure the voltage and current of the load from the generator in real time to see the actual impact of each of the connected devices. It is best to connect 2000W heaters (first one, then the second and third, etc.) and then see how they will impact the generator.

The Rotor is made of alluminium with a percentage of silver to help create the diamagnetic effect in the rotating magnetic field caused by the infused silver in the alluminium rotor..how much is mystery...balanced coring of the alluminium rotor to add silver could possible work...either all I'm a huge fan of this experiment it could potentially save the world...imagine this in a electric car

@alexandersandor7315

Жыл бұрын

Yes may help the silver but the silver only react if the magnet move over and even if you do move the magnet over the silver just a tiny effect while you move the magnet. On the rotor the magnet stay in one place in the cure of alu and silver so no effect of the silver I believe

@jamesprice6243

Жыл бұрын

@@alexandersandor7315 I believe the build of this device using the pullstart to give enough momentum to power the motor to self power is correct and possible...the idea of using silver within the magnetic field I'm going to have to test that out for myself I have built one without the solid rotar but a design of my own

What is the round cylinder on the side that has wires coming back into the motor? Is that a powers source?

very good

災害避難所や紛争避難所などの場所で活躍する事を願っています。 出来ることなら利益に走らず困っている方へ差し伸べる手であって欲しいです

Смотрите внимательно, после 17 минут когда он снимает Кришну двигателя, кадр меняется , это не будет работать , он аккумуляторы вытаскивает из под Крышки , потом кадр продолжается, во вторых нельзя с двумя катушками микроволновки получить 220 вольт

@user-mo9nz4ky3j

Жыл бұрын

@Václav Kapsář Напряжение там есть по 10вольт на катушке, но сила тока очень маленькое.На 17.18 и вправду кадр меняется.

Them 10A cables didnt even smoke. Also, just as amazing, you conquered a hydrogen bike. Well, if you hit 100k subs at $5/mth, you'd be a million air in a few months....and then I'd be jealous

Cuales son las caracteristicas del motor y que porcentage de plata y aluminio componen el rotor?

How many revolutions of the motor (rpm)?

are you the official channel for the liberty engine, or you are just distributing the video ?

Question #1 why only 4 coils, if you made each coil core is big enough for 2 coils? Question #2 if you really intended to only have 4 coils total, why not make the coil cores flush with the coil and closer to the magnetic wheel for a stranger magnetic effect? Question #3 why is this version only single sided devise instead of a double sided devise? Question #4 why aren't you using fuses to regulate the incoming flew before looping back into the motors power supply?

hello, thank you very much for sharing the Liberty Engine. Can you tell us in which mixing ratio you alloyed aluminum and silver and how big the radius of the rotor head is?

@alexandersandor7315

Жыл бұрын

Hi I looking the same thing but aluminium shadow the magnetic field silver only react a bit once the field moves I don't see much reason for silver mix

Everything that exist or has been invented, it's a part or a puzzle creation, and every part of it, should be enough to assemble in a different manner, in order to achieve a different result. This is my conclusion after observing creativity, all over the world. Remember this words. Thank you.

Where i find blueprints with all used materials and size of all them. Thanks

@xxgianlucax1

Жыл бұрын

SEGUO

@tomrandall4871

Жыл бұрын

Look up Howard Johnson he had a patent on a magnetic self running motor. Late 1970's ~ Early 1980's One of the hobbyists' magazines had a full article on his motor in 1981. Short time after the magazine was bought out. Poof it was gone.

The generator made by Hidden Technology is transparent, of course, I will make it too, it will be effective, thank you.

Сколько я не проверял но к сожалению не получается это сделать, да есть интересные вещи которые противоречат физике, но если у вас это работает то вы молодец.

@waleedness7148

Жыл бұрын

رسم توضيح للملفات وتوصيل لاسلاك

@jbcnc74

Жыл бұрын

@@waleedness7148 versteh leider kein Wort.

To remove some of the doubt, solder the wires on to the bulb, lay it on the table and and don't hold it in your grip of your hand. What's in the round cylinder that connects to the junction box at the top of the motor?

@jogi836

Жыл бұрын

Kondensator

so you are using an asynchronous motor with a steinmetz circuit to drive it with your theoretical single phase, first flaw because it is more or less a solution when you dont have the 3 phases or the right motor and its very innefficient... you have 4 coils but only connect two. the magnetic circuit may be present but just because the frame is welded to the laminated core and there is a reason for the laminated core... reduce eddy currents. but i am actually curious that would happen if you feed the motor with a 180degree phase shifted voltage (like yours) and use the steinmetz circuit.

Здравствуйте "Кулибин"! Для лучшей устойчивости этой БТГ я бы добавил пару элементов. Продлил спереди ось, надел бы подшипник и наварил стойку. Две пластины, на которых держится двигатель, надо продлить и приварить к рамке. Хотя бы слева и справа. А теперь пару вопросов: Сколько квт выдаст эта установка? Сможет 4-5 киловаттами поделиться? Зачем лишнее железо из бывшего тороидального трансформатора? Не для лучшего ли поля тора? Или вы тем самым избавились от паразитического затухания электромагнитного импульса? А теперь не по теме. Смотрели ли вы про генератор Серла?

@Ishchushchiy_Znaniya

Жыл бұрын

@макс иванов я не пытался кого то оскорбить. Откуда мне знать из какой он страны. И не надо всех под одну гребёнку. Иначе посчитаю вас троллем.

@FERRERO_Partisan

Жыл бұрын

В предыдущих видео он сообщал, что нагрузку может тянуть до 20 или 24 кВт, точно не помню. Но точно одно из двух.

@Ishchushchiy_Znaniya

Жыл бұрын

@@FERRERO_Partisan спасибо!

Hello ! ​@Hidden Technology , During the broadcast, you wrote about the alloy of Aluminum and Silver for the ROTOR ... But after all, Aluminum and Silver are non-magnetic materials, aren't they? No ?

@alenpasnikov

Жыл бұрын

It is about eddy currents.

Good day, great power unit. May i ask for the specs of the liberty 2 power unit ? I woulx like to build it, i dtay on a farm, no power at all. This will change my life at least, please.

Questa invenzione cambierebbe la vita al 90% della popolazione della terra . Il 10% che detiene ricchezze immense, se l'invenzione fosse vera, avrebbe gia provveduto ad individuare da chi e da dove sono partiti questi video

that looks like a pressure washer motor - how convenient it was already wound to your specification !

Congratulations fom Japan 🇯🇵 🇧🇷

@santojghosh

Жыл бұрын

Congratulations for what, exactly? Nobody is using even one of these. Nobody is even trying to manufacture and sell them. If this was real, then there would be no shortage of entrepreneurs investing in the manufacture of such an incredible moneymaker.

By any chance would you be interested in working with an entrepreneur to use this technology in an electric vehicle

large hum from a big mains transformer under the bench and even buried underground later in the video, he does a lot of tests at that same place on the riverbank, obviously has mains there to run irrigation systems, but i do like the video. Not enough magnets and certainly not strong enough to do the work he shows. think about it and you will see its nothing more than a electric motor with the drive transformer under the bench, nothing more that the mains that there at the water side that drives the irrigation pump being used to drive the motor go mislead one to into thinking its running without any power input.

nhạc té loa công xuất lớn những bộ dàn loa bát to quá chuẩn luôn tôi áp dụng nhạc này vào những bộ âm ly loa được nang cấp mọi người mê ly luôn không chê được thể loại nhạc này tôi cảm ơn ban nhạc người thực hiện phát trên cộng đồng mạng được mọi người yêu nhạc nghe thưởng thức nhất là những người làm loa và những dàn âm ly thông dụng trong cộng đồng

Hmmm.. Which type of inverter is hidden inside the capacitor, Take the capacitor out of the plastic case and show us what's inside by doing the test. And how do you stabilize Output Frequency and Voltage ???

@TolisOnLine

10 ай бұрын

Better if they install an rpm indicator, so we can see how the system rpm stabilizes with load changes. The rotor alone is heavy at 7.6kg, spins at 1400rpm. Notice at 8:24 when the starting string is pulled, it reaches some low rpm. Then the machine accelerates to 1400 rpm.

I would like to buy something like this if possible, and what is the price. Thank you.

People say it's impossible without any attempt That system is a fully capable technology, as we see in this video

Hello, dear. By watching this video and the previous video, the generator configuration video, I could not understand how I can link four files together. Please make a video about this thing.

Very coincidentally it puts out 228V regardless of the load conditions, never going up or down when loaded with the 3000 Watt heaters! Could it be that there is something else providing the 228V, maybe mains voltage?

@TolisOnLine

10 ай бұрын

Better if they install an rpm indicator, so we can see how the system rpm stabilizes with load changes. The rotor alone is heavy at 7.6kg, spins at 1400rpm. Notice at 8:24 when the starting string is pulled, it reaches some low rpm. Then the machine quickly accelerates to 1400 rpm.

Bonjour, J’ai eu l’occasion de tester la configuration que vous présentez et je ne vois pas comment vous pouvez sortir plus de 25V sur une bobine? Je pense que ce n’est pas possible d’avoir 220v et encore moins la puissance ! Si vous voulez bien me démontrer le contraire j’en serai ravi! Merci à vous. Nicolas.

ممتاز ❤❤❤❤❤❤❤

YARI N NMN TO KY JUAN DELASAG, HEHE😂😂😂😂

Very innovative and simple yet powerful and disruptive. How does the alloy material affect the magnetic field generated by the magnets and is it the same material as the cores inside the microwave transformer coils? Is it an aluminum alloy?

@jamesprice6243

Жыл бұрын

It's a silver infused aluminium rotor...silver cannot be magnetised but when placed into a rotating magnetic field it creates a diamagnetic affect

Why you dont put on an Oszilloskop instead of an normal Multimeter?

Can the alloy of the rotor share the silver and aluminum mix ratio I'll do another presentation to trust you

@alexandersandor7315

Жыл бұрын

I want to build one could you help me please do I really need aluminium and silver fix of material for the rotor or aluminium would be ok as well?

connect the output wires back into the coils around the magnets and watch it increase in revs until it flys apart

Dear viewers, how else can you be convinced? Everything is transparent. 👍

Have Been waiting over a month

what is the load capability?

I would like to know where they got the metal for the flywheel? I am a gearhead with my own garage and workshop. I have my own spinning lathe which I can build one… I just want to know if the aluminum silver metal was something that they melted together themselves, or did they buy it from someplace? I’d really like to try and put this design to the test and see if it really works! If it does, I will gladly like and support your video and advocate your work!

@mikehaertsch

Жыл бұрын

Alu und Silber Legierung. Ich würde Aluplatten zu runden Scheiben zuschneiden. Die Scheiben an einander Verschrauben und die Magnete in den Aussparungen in den Platten verklemmmen.

@augustuscaesarabarquez270

Жыл бұрын

its a silver aluminum material made that flywheel and places with neodyme magnets in it

@gt2699

Жыл бұрын

@@augustuscaesarabarquez270 i know what is on it, I just want to know how to get the materials to build it myself!

@benq994

Жыл бұрын

@@gt2699 It is shown in previous videos how he created it. However im not sure about the ratio of silver and aluminum.

@gt2699

Жыл бұрын

@@benq994 and once again, I’m not asking about how he “created” the metal flywheel… I’m asking if and where he “purchased” the metal for the flywheel! I want to know where he got the materials so I can experiment with it! I saw perfectly well, how he was using his machinery to create the flywheel, but I want to know where he got the silver/aluminum material to make the flywheel!

Altenator volt ampere ,how much? Power generator...watt?

Ok so how can I purchase a dozen or so?

Scusate ma ho una domanda. Si vede che viene collegata una sola bobina, quella superiore, e le altre 3? sono una decorazione? Si vede chiaramente che non sono collegate tra di loro ne in serie o anche in parallelo. Spiace è un bel lavoro

@nitionkey

Жыл бұрын

Chiaro,semplice 2 fili nero va bobina sotto come una caricatore wireless sotto banco, poi blu rosso va motore. È solo un video per avere click

Por que não levanta o aparelho para provar qye não tem nada ligado por baixo?

Ciao per favore mi puoi dare il link dove hai acquistato i magneti n52 grazie

I think you hid the batteries in those transformer/ magnet looking things.. and I saw you disconnect a lead of some sort, was that supplying the battery power to the motor/alternator?

Me gustaría tener uno de esos, cuánto costaría hacerlo?

How can I buy one?

What is the cylinder shaped item that remains unopened on the side of the box he opened on top of the electric motor? It looks like a battery to me.

@dgfgdsfds4128

Жыл бұрын

capacitor :-)

@superloop330

Жыл бұрын

@@dgfgdsfds4128 ok thx. I was thinking that might be a possibility.

How would you regulate speed and horsepower

@satishathreya6948

10 ай бұрын

increase the number of magnets and put more step-up transformers.

@TolisOnLine

10 ай бұрын

Better if they install an rpm indicator, so we can see how the system rpm stabilizes with load changes. The rotor alone is heavy at 7.6kg, spins at 1400rpm. Notice at 8:24 when the starting string is pulled, it reaches some low rpm. Then the machine accelerates to 1400 rpm.

Great. ...Except for one thing: Nobody has it for sale. Anywhere. That doesn't make sense. If this was real, then lots of very competent people (including Hidden Technology) would already be raking in millions by selling it. In fact, there are contractors in China that specialize in manufacturing inventions like this. Just hand them the parts list, schematics, blueprints, etc, and they will make as many as you want. But for some inexplicable reason, nobody (including Hidden Technology) wants to manufacture and sell this ticket to becoming a billionaire practically overnight. Hmmm...lol

@pioneerpilot1871

Жыл бұрын

ONLY problem history has made inventions like this fatal for inventors, they turn over plans and the plans disappear, sometimes along with the inventors. They have to be careful who they deal with

@benitoestilong9872

Жыл бұрын

Because its free

@user-bm4cp4mt5t

Жыл бұрын

Wait for the end of earthly cataclysms and the destruction of modern infrastructure from mid-August to the end of October 2023. In 2024, the survivors will receive these inventions.

@lazar.vision

10 ай бұрын

@@user-bm4cp4mt5t tis a bit early, 2040 is more likely for that (phoenix event)

The motor is DC or AC?

Hi brother. I want to buy. How much.

How do you control wear n tear

@joshualima6967

Жыл бұрын

You can't. But A/C motors are VERY robust and will last thousands of hours.

pero esos motores usan capacitor de arranque y no se lo veu por ningun lado explicame.

Which is the torque of this engine?

@KevinSmith-os5yz

Жыл бұрын

Zero, same as the power output.

I need to have one.. but I didn't find the way how to have it

To top it off, I accidentally stumbled across this video and I don't want to sound like the most skeptical person here. But if you claim that this engine is self-sustaining and produces infinite energy, we should now have a revolution in the energy field and not only that. And I haven't seen a big fuss made by the media so far. If this method of free energy production really worked we should also have seen a large-scale implementation in various fields. I repeat, I haven't read, seen, heard much about this "innovation"! I sincerely hope that what we see here is genuine. I can only think of the impact it would have on the automotive industry and beyond! God speed!

@dixy1221

11 ай бұрын

I so desperately wanted to believe this. I then studied this footage meticulously, they say "uncut" but in all honesty, they just did an impressive job in cutting the video. I noticed a few cuts which I think anyone can see if they look closely. One example is at 13:21 look at that thoroughly you will see it.

@preppervol

11 ай бұрын

the reason we don't have a "Revolution" is because people are too lazy to build their own... Everything you need to know is in the original video... all you need is the wiring diagram and you can build your own....

@elishamusa328

9 ай бұрын

I am trying it now,I will bring results here

@anteskojo5087

8 ай бұрын

@@preppervol Have you tried building it yourself?

@preppervol

8 ай бұрын

@@anteskojo5087 not this exact one, the one I built, does not utilize a motor like that at all... I use a BLDC motor, which is more proficient... People have been to my home and watched it in action and have asked me several times to make a KZread video explaining it and how to build it. I always turn down requests for the simple reason people are ignorant. just because they cannot get it to work for them, they will always bash those who have been successful in their constructions... A simple wiring diagram and elementary school science knowledge, anyone can make this and not have a problem... The wiring diagram they provide works like a charm... I will say this much, I am currently building my home, way out in the middle of nowhere, where the closest access to power lines is a half mile from my building site, to which I will invite people out to observe and study it in action... too many variables living in a grid tied location where people can make claims of trickery...lol...

Where can i get it how ist the Prize

💯💯💯👍👍👍❤️❤️❤️

Sarei interessato a provarne uno di questi generatori. Come si fa ad avere?

They that don't believe did not know about how electricity Made ...they just know how to use ..

@laynabirchwood6564

Жыл бұрын

Translator please.

@dondedieukatshingu8033

Жыл бұрын

True

I'd love to know and understand more do you have a website and contact details

there are no lies in this video.

I'm very sorry, but shouldn't the coils be as close as possible to the rotor magnets

@dixy1221

Жыл бұрын

Yes, it should be, but as far as I can tell, it's close enough.

Aucun test de puissance fournie. Et c'est ça le plus important !

can i buy it?

I want to see how they are controlling the hertz frequencies.

@radojevicslobodan

Жыл бұрын

Why ? Goal of this Engine is power as i see it... controllers are another step

hello, my friend of Hidden technology, can you tell me in detail about your motor, how many klv and how many watts, if it's not a secret, I'll wait for your answer.

@KevinSmith-os5yz

Жыл бұрын

The whole thing is nothing but click bait for the gullible. It can't and doesn't work.

How many rpm does it get.. ?

@FERRERO_Partisan

Жыл бұрын

14000 RPM

Bad move 👍🏽👍🏽👍🏽

@HiddenTechnology_

Жыл бұрын

Soon we will release another video. There will also be a longer version for members

Please share 100% to all subscribers so that we can trust them. From one to ten.

Why you give not buying or free plans? i need one im thinking only click bait here.

You are honest. I did this experiment, and a voltage of 110 volts was taken out, and a 1800-cycle drill was powered by it, and a 3000-cycle drill was connected to me, and a voltage of 154 volts was output.... For this I ask you for the operational board of the motor, please.

@KevinSmith-os5yz

Жыл бұрын

You claim to have made one, talk to me I have 10 grand us for you:)

@sekour

10 ай бұрын

@@KevinSmith-os5yz And, alas - _CRICKETS!!!_ (It's all BS - unfortunately.)

@sekour

10 ай бұрын

(Because I'll raise you 10K if it's true)

I want one, I need it, I’m homeless

Tra due inquadrature identiche alle volte c'è un salto temporale questo vi consente di levare i cavi che entrano da sotto. Io vorrei che la vostra invenzione funzionasse ma qualcosa non mi convince. Provate a sollevare il motore mentre è in funzione. Grazie

Over and over again you post and NEVER answer questions. If this was real you would interact. Is it only views that you are interested in?

@KevinSmith-os5yz

Жыл бұрын

Ah, you found him out:)

@sarajones646

11 ай бұрын

Pay attention to Dr Steven Greer. Too many people have died for this technology. I'm not surprised you didn't get an answer.

@hidayetcelik1001

10 ай бұрын

Ortada teknoloji filan yok saçmalık var birde süslü kelimeler var birde 40*2 mm 16 adet mıknatıs ve bunlarla 20 000 volt üretir palavrası var durum bu

How can i order

Pero si real mente funciona a mi si me interesa.

OK MI HAI CONVINTO. COME POSSO AVERNE UNO?

كم هي قوة المحرك وكم سرعة الدورة 1400