Nice build. Definitely going to copy some of your ideas. Thank you for sharing.

how did the 3d printed star hold up? I have thought about doing the 3d printed start but figured it wouldnt hold up to the elements. What type of filament did you use. thanks

@justinzdesign

11 ай бұрын

Worked out fine, held up to the wind storms and winter weather. It's printed in PETG, I've sold a few and know others that have used it and the only one I know that broke was when a full 20 megatree fell over

Are those 80# bags of concrete?

@justinzdesign

21 күн бұрын

I think they were

Great Job! What controller are you using? How much do you think you have into it. I want to build one.

@justinzdesign

Жыл бұрын

Running off a kulp k8 plus a smart receiver. Probably close to $1000 when adding up all the bits and pieces

Great video. What was the height on your main pole?

@justinzdesign

Жыл бұрын

I think I cut off about 14 inches off so it comes to 8 feet 10 inches. I put up the full 10 foot pole first then measured to see how much to cut

How did you wire up the strings. Did you do one long chain, split them to 8 chains, do 16 individual lines, or some other combination. Is your controller at the tree or do you run it to a central location? If it is a central location how long is your run? I built one last year and I am trying to improve my design, totally using a lot of your construction ideas. Fantastic video!

@justinzdesign

Жыл бұрын

I have it wired as 8 ports, 100 up and 100 down and then another port for the star. Controller is a K8 plus smart receiver that is specific to the tree and mounted to the pole

Is the star made from Delrin?

@justinzdesign

21 күн бұрын

3d printed using PETG

How you are you attaching the strips at the bottom and are you just muscling up the pipe with everything on the topper then attaching the bottoms?

@justinzdesign

Жыл бұрын

Lifting up the pipe with the topper, then ladder to hang the strips, at the bottom they are attached with bungee balls and I ended up adding screws with a washer to keep everything spaced out

Hi was these 12v or 5v pixels ? did you use a dig quad on these and how many power injections and how many power supplies did you use and what amp power supply .

@justinzdesign

Жыл бұрын

12v with no power injection running at 70% brightness for testing. Running a k8 now but I did test all the LEDs with a quad previously and it worked. All running on one 29 amp power supply

@blackdave8525

Жыл бұрын

@@justinzdesign great job and thanks for getting back to me on this .

Is there a parts list available? Love the design!

@justinzdesign

10 ай бұрын

This is what I have from when I did my home depot run, some of the items are "generic" as I pieced it together when there 5 Gallon Bucket 2x8x10 Pressure Treated 4 bolts (1/2" x 6") 8 nuts (1/2") 8 washers (1/2") 2" x 2 foot long pvc sleeve 2 bags of fence post concrete 1.5" rigid conduit Flanges for topper (to conduit and to emt) 4 Bolts (1/4" x 1.5" 4 Nuts (1/4") 8 Washers (1/4”) Reducers for flange to topper pole Bolt/nut to lock in pole to sleeve

@comiser

8 ай бұрын

Do you have a link for the sliver reducer?

What's the diameter of the tree and how many pixels per string?

@justinzdesign

Жыл бұрын

At the bottom about 40 inches, 16 strings of 100 pixels at 1 inch spacing

What size J bolts?

@justinzdesign

6 ай бұрын

Got the ones from YPS with the topper: yourpixelstore.com/product/j-bolts-1-4-20-x-2-5-16-pack-of-16/

I wonder where you got the concrete in the 5gallon bucket idea. LOL

@justinzdesign

Жыл бұрын

A long list of great people that started with you!