I could swear that I was missing parts until I saw your video and realized I was inserting the switch backwards. Thanks so much...now it works great again!

@Dhulfiqar

3 ай бұрын

You're very welcome! Glad you fixed it.

@jonanjello

26 күн бұрын

Likewise for me, too. I found my blacklight LED light for finding scorpions. I still couldn’t get the switch assembly to work, so I swapped it for another similar pocket light.. I plan to search tonight! Thanks!

Thank you, my light fell apart at the on/off button and the pieces dropped to the ground when I unscrewed the back. I found the pieces but could not be sure it was complete without a guide and to reassemble, even more mysterious. Your video helped a lot. I had all the parts and it was only a matter of assembling. With your video, very easy. Thanks again, DP.

Thank You. This had been so helpful. I was about to throw away the flashlight when I remembered consulting youtube. Now my flashligth is working again.

Thank you for making this video. It helped a lot. The switch suddenly sunk in and when I unscrewed the flashlight to fix it, everything jumped out and I spent an hour trying to put it back lol. now it’s fixed! ☺️

@Dhulfiqar

Жыл бұрын

You're welcome!☺ Glad you fixed it.

Thank you brother, you showed me the one thing I was missing in the on/off switch assembly. I was not securing the little black clicker properly.

@basshunter407

5 ай бұрын

Me too, I couldn't figure it out.

Thank you. I couldn't figure out the on off switch assembly. This is my favorite flashlight around the house.

@Dhulfiqar

5 ай бұрын

You're very welcome!

I spent 2+ hours trying to put this damn flashlight back together because the switch end popped out. Had no idea the switch was directly touching the rubber... I had the the damn housing piece switched around. Thank you so so so fucking much!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Watched your video and figured it out in 5 minutes!!!!!!!!!!!!!

Very helpful video, very clear. The only problem for me was that the part where the bulb is situated IS SEALED and cannot be either opened or completely unscrewed to separate it from the tube where the battery goes. The torch has DELIBERATELY been designed this way in order that you CANNOT JUST REPLACE THE BULB costing about 2€ but are FORCED to buy a NEW TORCH.

@miklemikemuster

5 ай бұрын

I got to my bulb on my "focusing" bulb by peeling off the rubber hood. (it's lightly glued) Then unscrewing the lens cap to get to the bulb.

@judgeroybean6930

5 ай бұрын

I thought I had tried all things possible to open up where the bulb is but nothing appeared to undo, I was so p****d off after about 2 hrs of trying I just chucked itBUT I am very grateful for you taking time to make the video and explaining and I shall keep it (for future reference). thanks a lot@@miklemikemuster

Thank you. I love this flashlight, and have been trying to repair it, when I ran into your descriptive video. All fixed and functional.

@Dhulfiqar

7 ай бұрын

Glad you fixed it. You're very welcome!

You're the only one that I saw quickly with a switch assembly! Thank you! 🙏

@Dhulfiqar

10 ай бұрын

You're very welcome!

Thanks for the video. 2 years of sitting on top of the tool box I was about to throw it away. Switch configuration was way off lol Stretched the button spring to avoid it falling apart again. Thank you

@Dhulfiqar

10 күн бұрын

Glad you fixed it. You're very welcome!

Best video to fix my flashlight! Thanks a lot!

Thank you again I got bored and wanted to fix my wifes flashlight switch. This showed me the way to take it apart. Mainly corrosion on the little contactor inside.

Thank you so much!!! Your video showed me how to put the damn thing back together - and it's finally working! Thank you.

@Dhulfiqar

9 ай бұрын

Glad the video was helpful.. You're very welcome!

Thank you so much for your video - you also helped me reassemble the switch

Thank you! Very good job detailing this with pictures

@Dhulfiqar

11 ай бұрын

You're very welcome!😊

i thought mine was broke . just before i tossed it i took it apart then decided to look on youtube as a last chance and there it is. you showed me and mine works. ty

@Dhulfiqar

2 жыл бұрын

You're welcome!

Useful video fixed my flashlight that I needed for work

Yay. I needed help fixing the end of it

Thanks! This was helpful!

Thank you for making this video! My flashlight kept switching between the different lighting modes by itself or sometimes it only turned on when i tapped it a few times. But with this video, i was able to take it apart and find the problem.

@Dhulfiqar

Ай бұрын

You're very welcome!

I purchased one of these lights and the orange rubber switch cover was sitting off to one side. I was unable to adjust it. With the help of this video I was able to remove the tail cap and re-seat the cover. The cover did not come out easily. It was trapped on one 'corner'. I placed the tail cap unit on a writing notepad to avoid any damage to the surface or the tail cap itself. Then I used a Philips head screwdriver to gently tap the 3 sides of the switch. This freed up enough room to release the cover. Another few taps and the switch was released. Placed the rubber cover back in the hole and tapped the switch back. An easy fix. Thank you for your video. It will also be useful if I decide I want to upgrade or change the led.

@Dhulfiqar

3 жыл бұрын

You're welcome David, true, but I prefer using a wooden stick or any plastic object to push the switch assembly out of the tail cap as the steel screwdriver (especially the thin ones) might crack the plastic switch assembly.

@davidr954

3 жыл бұрын

@@Dhulfiqar Yes, I would have preferred to have used something non-metallic to avoid any damage, but I didn't have anything else suitable. The screwdriver I used has a 5mm wide head. One that's wider would probably be better to even out the force. I certainly wouldn't use anything smaller, as this would likely puncture the switch. Obviously your method is better, but if you don't have something suitable to act as a drift, then the screwdriver can work. As long as you go easy and don't apply a lot of force.

Very helpful video.

Thanks. Good works.

Thanks sir My torch had been shut down for months today it got lighten up again and I'm so happy. Thank you so much ♥️

@Dhulfiqar

9 ай бұрын

I'm glad you fixed it.. You're very welcome!

Thank you you really helped me put back the switch assembly. Thank you so much.

Thank you. My end cap with switch came apart on the job and by the time I picked up the pieces, I forgot the order of assy.

thanks for this, I had a shadowhawk torch which had a rattly glass, i didn't realise it screwed into the head, after seeing this I used a pair of pliars to grip the ring and screwed it back into position, no more rattle.

@Dhulfiqar

Жыл бұрын

You're welcome! Glad the video was helpful to you.

Man this was a lifesaver!! Thank you!!

@Dhulfiqar

Жыл бұрын

You're welcome!

Thanks it works!!!

Is it possible to cancel the sos blinking light mode?

Merci beaucoup !!! 👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼barakalahoufik

СУПЕР -- пупер . Спасибо . ТАК держать ! ! ! . ВСЕХ благ .

@Dhulfiqar

2 жыл бұрын

Spasiba Viktor )

Thanks ,, for sharing ...very informative...

Insightful and helpful. Thanks!

@Dhulfiqar

26 күн бұрын

You're welcome! I’m glad you found it helpful.

Thanks man for helping. Jazak ALLAH

Hello, thanks for the disassembly video it was very useful! Do you have pictures of the front of the driver (the other side of the spring) where the ICs are located? Also have you measured the voltage the LED runs at? Would be very helpful if you have that information!

@j03lturn3r

2 жыл бұрын

I open this flashlight up to delete mod. See here 👍 kzread.info/dash/bejne/ZGx7mKeGopifkaQ.html

Thank you ❤️👍👍

Where can I order a new switch assembly? Mine came apart and I don't have all the parts to reassemble. Thank you.

Thank you so much b=brother, you're such a life safer

@Dhulfiqar

11 күн бұрын

You're very welcome brother. Glad my video was helpful to you.

Exelente y por demás didáctico el vídeo, un saludo desde Argentina

THANK YOU!

@Dhulfiqar

6 ай бұрын

You are welcome!

Great video thanks!!!

@Dhulfiqar

Жыл бұрын

You're welcome! Thank you for watching!

Thanks very much. I kept trying to put the switch back together the wrong way

Great video. I was wondering if you knew where to get the rubber o- ring or gaskets to the pill assy. One has broken.

@Dhulfiqar

Жыл бұрын

Thank you! That O-ring around the pill probably tore because it was not lubricated.. apply a little bit of any grease on them or petrolium Jel to lubricate them. There are sets of O-rings from websites like Amazon/Aliexpress.. Just measure the o-ring and order the set that contains it. All the best.

I was you have constructed a new lightsaber. Your skills are complete. ✌️😎

YOURE AWESOME

Sir how fix glass

onde posso comprar a lampada? e como sei qual e que serve na minha lanterna??

Thank you for your video. I didn't know how to remove the switch.

Thank you

@Dhulfiqar

6 ай бұрын

You're very welcome!

Thank you for the assembly part of the video. After replacing my battery the parts fell apart and couldn’t figure out how to put it back together

@Dhulfiqar

Жыл бұрын

You're welcome!

is it a Li-on battery? I have that flashlight, but it uses 3 x AAA alkaline. I would like to switch to that battery

thank you

@Dhulfiqar

Жыл бұрын

You're welcome!

Thank you friend very good👌👍🍀

@Dhulfiqar

Жыл бұрын

You're welcome!

Thanks for the vid but the front part where the LED is does not come apart. I've tried vice grips and plyers but the little peice on the tip does not come off, so no way to get at the LED to fix that white peice that came loose.

We have similar flashlights but I cannot remove the front lens on mine the way you did so easily. I wonder if there may be some sor of glue used on mine. I just have to fix back the reflector which was knocked loose after some drops.

@Dhulfiqar

2 жыл бұрын

The lens wasn't removed from the cap in mine too. The Aluminium cap is tapped on the sides to lock the lens in place.

@ThePeanutization

2 жыл бұрын

@@Dhulfiqar I mean the aluminum cap on mine wont come off. Maybe I'll try to use some tools to get more grip. thanks.

@Dhulfiqar

2 жыл бұрын

​@@ThePeanutization Yes, you need a Needle nose pliers to unscrew the LED Pill (the Silver part that holds the LED and the circuit board) it is what prevents you from removing the Zoomable head. All the best.

Hi, for the zooming expendable neck, ours is loose, when we point it downwards the neck drops and when we point up, the neck drops. Do you know how to tighten the neck pls?

@Dhulfiqar

2 жыл бұрын

Hi. You can tighten the neck (the sliding part) by removing it, you will see two rubber rings (O-Rings) on the silver part that contains the LED (the pill). Remove or reduce the lubricant oil on the O-rings using a tissue and some rubbing alcohol. Now the sliding part will be tight. If it becomes too tight, then put some petroleum gel on the O-rings and so on.

Si te entendí muy bien gracias!..

@Dhulfiqar

Жыл бұрын

De nada!

Thanks! - I had the same problem all pieces jumped. My other problem is that it lost something for "stretching" the light (zoom).

@Dhulfiqar

6 ай бұрын

You are welcome! You most likely lost the O-ring that the zooming mechanisim slides on.. The O-ring sits on the Pill (The bare aluminium part that houses the LED and the circuit board) It is recommended to lubricate the Ring a little bit but not too much to make it slide easily but not too loose.

I was ready to throw mine away..then saw this..works great again!!

@bbdudeyt

4 жыл бұрын

me too!

@ncameron7

4 жыл бұрын

What was wrong with yours?

what is the diameter off the driver?

Can I get glass part of this torch

@Dhulfiqar

3 жыл бұрын

I think Aliexpress sells lenses for zoomable flashlights, just search for the size in millimeters.

I can't seem to get the lens off, am i missing something or cloud it be glued on? It's very tight.

@Dhulfiqar

3 жыл бұрын

You can unscrew the Aluminum ring that holds the lens.. but if you mean removing the lens itself from the Aluminum ring, then the lens is non removable in the shown model.. it is somehow secured to the Aluminum ring.

@PhillyMacPhil

3 жыл бұрын

@@Dhulfiqar Ya, its the aluminium ring i'm having trouble with, doesn't want to budge.

@MouthBout

3 жыл бұрын

@@PhillyMacPhil Same deal. Did you get yours off? I'm using pliers and it's not working..

@skip741x3

3 жыл бұрын

@@PhillyMacPhil bro, i just ran into this...some of these lights look identical but dissasemble Differently! my bell and howell for instance does Not unscrew at the lens end,even though it Looks like there a seam there, its all one piece..i was gripping it with vise grips trying to unscrew b4 i realised it has a Press in ring around the lense, you just use a small screwdriver to pry it up and out comes the damn lense.. wish i'd know this b3 marring it up with the visegrips!

Hey brother what kind of battery does that take I can't find a battery and I have the same flashlight?

@Dhulfiqar

2 жыл бұрын

Welcome Ray, this flashlight uses a Lithium 18650 battery. Thanks for watching.

I will try at home

how can I return the glass that fell and then was removed, I put it back and removed it again

@Dhulfiqar

2 жыл бұрын

Sorry I don't understand the question, can you write the timing of the video that you are asking about?

@bridgetteivantamayo

2 жыл бұрын

ok I didn't see the lock in the mirror

@bridgetteivantamayo

2 жыл бұрын

I saw now left where it fell

I have got the same flashlight but with V6 diode and it seems is sealed for waterproof. There is not that ring on lens side to twist off. How to disassemble my flashlight?

@Dhulfiqar

3 жыл бұрын

you mean there is a plastic gasket sitting on the LED (press fitted)? if that is what you meant then watch this video as it has the same design: kzread.info/dash/bejne/jIaNp8aoqbbXlLA.html

@conradvandien3495

3 жыл бұрын

@@Dhulfiqar yes that's quite right such as you meant plastic gasket. But model of flashlight is the same as yours. On that video is different design. There is no way to remove it without using brutal fotce?

@Dhulfiqar

3 жыл бұрын

That's the only method I know.. good luck.

@skip741x3

3 жыл бұрын

@@conradvandien3495 press fitted plastic ring on the lense end ..pop thta out with small screwdriver... some of these Dont unscrew

@conradvandien3495

3 жыл бұрын

@@skip741x3 Is that plastic ring fitted by glue? Should I pop it and stick it after by glue again? I have not solved that issue yet....

Please 18650 touch charging pin port repiar

how to disable the different modes every time you turn on/off??

@Dhulfiqar

4 жыл бұрын

I think you mean memory removal from the flashlight? kzread.info/dash/bejne/eKehyZJuisWac5s.html this video will show you how to make your flashlight always run at the high mode when you turn it on (instead of running at the next mode)

@j03lturn3r

2 жыл бұрын

Yes flashing is a pendejo 🤪 See my delete mod 👍kzread.info/dash/bejne/ZGx7mKeGopifkaQ.html

Trying to get the lens part off. I am pulling and twisting counter clock wise but all I do is scratch up the metal inside. What am I doing wrong. It’s a Letion.

@Dhulfiqar

3 жыл бұрын

if it's too tight, then you need to use a needle nose pliers to unscrew the pill with it ( the pill is the Aluminium part that holds the LED and the driver)

@skip741x3

3 жыл бұрын

press fitted plastic ring on the lense end ..pop thta out with small screwdriver... some of these Dont unscrew

Hi, I'm not very technically minded, I have one of these torches and the head which controls the zoom function has become loose. It moves loosely up and down the body of the torch and cannot stay on one zoom function. Which part do you think is broken and how can I fix it? Thank you very much.

@Dhulfiqar

2 жыл бұрын

Hi Rebecca 1- Either the O-rings that sit around the pill (the black rubbery rings around the silver part that contains the LED shown in 0:41) is lubricated too much that it makes the lens move loosely (you can reduce the lubrication by rubbing it with a tissue containing a little bit of cologne or any rubbing alcohol) 2- The O-ring might be cut or not sitting in its groove. You're welcome.

@reb_d1143

2 жыл бұрын

@@Dhulfiqar Thank you so much for your help.

@Dhulfiqar

2 жыл бұрын

@@reb_d1143 You're welcome.

Hi, Kindly help me to replace on/off switch of Lumintop ODF30C flash light.

@Dhulfiqar

2 жыл бұрын

Hi, I don't have that flashlight model so I don't know unfortunately.

Where can I find a replacement LED ?

@Dhulfiqar

3 жыл бұрын

You can buy LEDs from Aliexpress.com or Fasttech.com or Kaidomain.com and many other websites.

The top part of the head will not unscrew what do you recommend It is the same as your flashlight.

@Dhulfiqar

2 жыл бұрын

You need to use a needle nose pliers to twist it if the first method did not work.

You don't show either O-ring. What controls the focus adjustment?

@Dhulfiqar

3 жыл бұрын

the O-rings are @ 1:08 (Two black rings on the LED pill [The silver part]) These are lubricated with grease, they smoothen the focusing adjustment and seal from water.

Every where tells me use USB port to recharg my ATAK flashlight.. but it has no damn USB port just 3 brass prongs at end . Please help.

@Dhulfiqar

Жыл бұрын

I would love to help but unfortunately I don't know because I don't have that flashlight model.

i'm still have a difficulty to open the pill,i want to change driver

@Dhulfiqar

3 жыл бұрын

you need a needle nose pliers, it is a great tool for disassembling flashlights

@firstnamesurname1227

3 жыл бұрын

@@Dhulfiqar finally i can open the pill and change the driver,but i got new problem,,i'm used sst40 led and convoy diy 4 mode driver,when reach 35% and 100% mode its always blinking like sos,do you know what's wrong??

@Dhulfiqar

3 жыл бұрын

I think and I'm not sure, if you used a driver that has 4 stars, probably the driver is the cause (but i'm not sure), submit your question in BudgetLightForum.com and you will certainly get the answer because I have not used an SST40 LED before.. good luck.

@firstnamesurname1227

3 жыл бұрын

@@Dhulfiqar i've got an answer,it's led to hot or battery low voltage,,since diy convoy 4mode driver has a temperature control,

@j03lturn3r

2 жыл бұрын

Delete strobe/SOS mode 👍 kzread.info/dash/bejne/ZGx7mKeGopifkaQ.html

Yung akin po di rin po gumagana kahit bago battery na nilagay.kinakalawang na din po yung lagayan ng baterya triple A

Can you disassemble MZ 035 torch light please

@Dhulfiqar

28 күн бұрын

Unfortunately, I don't have that torch.

@l.rmeetei4451

28 күн бұрын

@@Dhulfiqar actually I don't know how to open MZ 035 but I try.... it's disassembly is starting from headlight of the torch

Thanks. That 5 mode was driving me nuts.

@j03lturn3r

2 жыл бұрын

It really is torture 🤬😂

Is the problem in the switch not understanding what is fixing ng

@Dhulfiqar

Жыл бұрын

You can determine whether the failure is caused by the switch or the LED/Driver by using the method shown in this post. diyfixingthings.blogspot.com/2018/03/how-to-troubleshoot-flashlight-and.html

How to open the top portion ...it is too hard.

@Dhulfiqar

4 жыл бұрын

pull the head and keep pulling while twisting it, it is shown here 0:25, it is an alternative method in case you don't have a needle nose pliers

I'm environmentally conscious so I have been using rechargeable batteries for my Tac Lights which use up a lot of juice. There is no information on B&H Website about recommended voltage for batteries. Anybody use rechargeables out there?

@Dhulfiqar

6 ай бұрын

Which battery does your Tac light take? This one takes 18650 batteries which their voltages are 3.7V.. there are dedicated 18650 chargers on Amazon. All the best.

But isme open karne ka option nahi hai

I cant unwind the lens

@maxhi88

3 жыл бұрын

Me too. Did you also wash it and it dogged up inside? And did you get it off??

Umm.. you never showed how to take the glass out or put it back in.

@Dhulfiqar

2 жыл бұрын

Watch 0:08 (the Aluminium cap is tapped to secure the glass into it.. the glass can't be removed from the cap.)

I did all this disassembling only to determine I had the battery backwards 🤦‍♂️

@Dhulfiqar

8 ай бұрын

😄

Thank you the on/off button fell apart. It's not a very good flashlight imo.

@Dhulfiqar

5 ай бұрын

You're welcome!

Main part of the vid missing .

@Dhulfiqar

Жыл бұрын

Could you specify which part of the video is missing?

@omsingharjit

Жыл бұрын

@@Dhulfiqar how to remove front lens Glass

@Dhulfiqar

Жыл бұрын

@@omsingharjit The front magnified glass is not removable unfortunately because it is tapped into the removable Almuminium ring That can be seen here 0:08

@omsingharjit

Жыл бұрын

@@Dhulfiqar but in mine it's not even removable but looklikes it's . But there is kind of O Ring above the lanse may be it is .

Inshallah my brother. 🙏

Thank you so much! I was about to throw my uv light and wait for my others to arrive hahahah this helped me alot. The metal plate should be outside not the inside hahaha 🫶❤️

@Dhulfiqar

2 жыл бұрын

Glad you fixed it. You're Welcome!

THANK YOU!

@Dhulfiqar

4 ай бұрын

You're welcome!