Absolute loving your videos. Keep up the amazing work!!

@Corn-ped

2 жыл бұрын

Thank you! Ill keep em coming!

Very Nice video! Keep up the good work man

@Corn-ped

2 жыл бұрын

Thank you!

Cool video, can't wait for the next one.

@Corn-ped

2 жыл бұрын

Thanks Wayne!

@waynekerrgoodstyle

2 жыл бұрын

@@Corn-ped Just giving you my opinion :-)

Good video I look forward to your videos

@Corn-ped

2 жыл бұрын

Thank you!

Love your video's!!!

@Corn-ped

2 жыл бұрын

Thank you!

Been running my polini for 2 seasons. I’ve followed several build guides but have never seen this. it always looks perfect when I check it But I’m def getting flutter! Hopefully this will help. Keep up the good work man.

@Corn-ped

2 жыл бұрын

Do it up! Check out spark plug side gapping too!

@Sensei948

Жыл бұрын

@@Corn-ped OIL MIX 33:1 IS OK ?

@Corn-ped

Жыл бұрын

I like to run less oil. 50:1 or 60:1 full synth

Thanks bro

I think to get the most out of my Jawa, plus it likes to soft seize. I think I need to do this. All I can do to make this little wh**e get to 45mph. Ok gonna do this before I slap it back together. Your channel has really helped me. Thank you.

@Corn-ped

3 ай бұрын

Get that JAWA GOING!

@RandyPopPez

3 ай бұрын

@@Corn-ped spoke with Josh at BillBunes today. This cylinder is on its way out this afternoon. 🥵🥵

Could you please make a video with a comparison of the stock piston, compared to this one... It all sounds great, but there´s 100 YTers doing they same, and also never showing any plausible results... It could all also be just fairy-tales...

SUPER RIGHTEOUS ! Great video!

@Corn-ped

Жыл бұрын

Glad you liked it!

Thank you CornPed!!! I did the gas porting and the plug side gapping you showed and OMFG the polini is so fast! I'm not joking bro its insane paired with a proma circuit pipe. Thanks bro you are the shiz😎

@peterdarr383

2 жыл бұрын

Can you or someone else explain the mechanism of how his "works" and how this creates more horsepower, also, applications to chain-saw and other small engines like an Echo 2400 - 210 series of lawn equipment. TIA

@thomaspeffer3885

2 жыл бұрын

@@peterdarr383ringland porting the TOP ringland on the piston causes the top piston ring to act like a dykes ring creating a better seal and more power plus helps cool the piston since more mix can get around the top part of the piston

@thelongranger55

4 ай бұрын

@@thomaspeffer3885sweet ! Gunna try it on my old ms290 piston before I put it back in . I wanted to drill holes for the transfer port bridges but the piston has a cut away on each side of the piston . It’s amazing how this stuff works let’s alone how it was discovered. every herd of the one where the drill small hole through the top of piston or was my leg being pulled ?

Re-watching this video one month later, would it be some sort of not good to put a lateral gas port on the piston where the exhaust port is?

That induces carbon buildup creating stuck rings in 2000 miles. The Piston seizes up at the bottom skirt area. From overheating from lack of lubrication/lean mixture. Only drive it at night😅😅😅😅 or do what someone did in the 70s that is drill approximately.020 deep divots on both piston skirts to catch oil. 1/4 drill you can drill them evenly spaced in a pattern if desired at least five divots no need for more than 10 on each skirt. Then you can haul ass Non-Stop

I've been porting chainsaws for years and never would've thought about piston porting and probably v wouldn't have heard about it if i didn't see your video it's brilliant and most husqvarna saws use a single ring

@Corn-ped

8 ай бұрын

Give it a try! Pair it with a side gap spark plug!

@Psy6o

8 ай бұрын

@@Corn-ped I never heard of a side gap plug either I'm going to watch that video now

Cool concept. How deep are you drilling?

Tq bro..❤

Could you make a porting video for beginners

can anyone explain to me what the purpose is of the 2 blind big gaps above the pistonpen? i guess it has to do with cooling or some sort? cant find any info on that

hello! I'm gonna try this but what is the difference between this and vertical gas porting when you drill through the top of the piston? would that also work on a 2 stroke? also why don't these holes cause blowby? to me drilling these holes sounds like bypassing the ring? and also does it matter when drilling if it nicks the ring land itself as long as it doesn't hit the lower part you said? and why do you drill on the top and not bottom?

Where is the dyno test?

what the Dark sorcery!

Dynosheet before and after?

very neat. do you have a still picture of that close up so we can see how much material is coming out?

@Corn-ped

2 жыл бұрын

yeah, its not much. I can post it in the community tab.

Ever presented any testresults?

How does it increase compression,?

What effect does it have on reed action and longevity though?

Is there any relationship between the cylinder ports and where the ringland ports go? Like centered in the ports or only on cylinder wall or just evenly around the whole piston?

@Corn-ped

2 жыл бұрын

I have tried both and not noticed any difference.

Pressure Paths in compression rings

Hey love the info is it possible that you could get a zoomed in image of what it looks like after I have a older Franco morini s5 engine that all use the same bottom end but the top end uses different cylinders and to of the top ends have double piston rings but I have one rope end that only uses one ring if you could up load a image or send me an image of what it looks like when done and you probably answered this already but if I may ask how come this wouldn’t work on double ring basically double the holes and offset them just wondering

@Corn-ped

Жыл бұрын

Ill post a photo in the community section for ya. www.youtube.com/@Corn-ped/community

Also is it true that if my cylinder has a chip or dip below or above the cylinder ports that it’s still good to run or something along them lines?? Just wondering your thoughts strange thing is that this engine ran fine until the main drive sprocket broke I will say I did have quite a bit of oil spitting out the back of the silencer so is that also known as blow by??

@Corn-ped

Жыл бұрын

yeah if you have a chip/dip and it doesn't have sharp edges for the ring to catch you should be good. Blow by is when the premix leaks past the rings into the crank case. oil spitting out if your pipe is from running to rich.

Great videos! What is the origin of the name Cornped? Do the gas porting grooves need to go all the way to the top of the piston? Looking at the pics in the link to MA that you posted, his ports are like half moon shaped.

@Corn-ped

2 жыл бұрын

They do NOT need to go up like a half moon. That guy did HUGE ones with a drill bit. You only need a notch. Back when people started doing it, no one knew about micro bits so people were using the smallest drill bits they could find. CornPed came from my name Maize which means corn and mopeds, Ped. Its not that original. I made a blog like 15 years ago and at the time someone was calling me CornFace, so I decided to call the blog CornPed. I could choose a different youtube name but I havent thought of a better one.

@rexsheler1321

2 жыл бұрын

@@Corn-ped are the porting grooves the same depth as the ring groove?

@Corn-ped

2 жыл бұрын

@@rexsheler1321 yes. it goes all that way in.

@jeffcombs2950

2 жыл бұрын

Here in Iowa we're all corn fed.

I was gonna build a setup with a polini kit on my free spirit pretty soon do you have any other tips for polinis? Parts I have: Polini kit Estoril sidebleed 17 tooth gear (free spirit 1 speed so 35 in the back) should I go with a bigger rear sprocket? Clone 15 bing (might switch to the mallosi 4 petal and a mikuni vm20) Running stock points Treatmetric 3 shoe clutch Let me know what you think and if I should change my setup at all. I was running an airsal kit with a biturbo pipe before and it caught a ring on the exhaust port unfortunately. I was looking for about 50mph but I haven’t switched out my front forks or changed any suspension components so that might be a little aggressive. Thanks

@joshe2420

2 жыл бұрын

Maybe switch out the front sprocket to a smaller one, like a 13. Ive heard that shorter chain is better so ye. And about the bing, make sure you use original 2.17 atomizer and original jets for it

@Corn-ped

2 жыл бұрын

I would use a real bing 15 carb or a larger one. Oko carbs are great, Mikuni VM 18 or 20, Del 21. I would also go to 16x40 gearing. Thats my favorite. Marty has a great gearing calculator if you want to mess around with gearing and speeds. A stock polini revs to around 10K. you can get them to rev out to 13 if you go nuts. toolbox.martysgarage.info/

@JackWalked

2 жыл бұрын

@@Corn-ped thank you for the response that gear ratio calculator is very helpful.

I'm going to try this on my 2 stroke 78.5cc 80/100 bike engine. Using just 1 ring with reliefs. Oh, it's a reed valve engine

I'm new at the game, is 'ghosting' the same as ring flutter ? Thanks., You picked up a new subscriber.

@Corn-ped

Жыл бұрын

hmm I have not heard of ghosting?

@thomasgronek6469

Жыл бұрын

@@Corn-ped Some of the newer model Stihl Chainsaws ( MS362 specifically ) experience a problem which has become known as ghosting. An unexplained phenomenon which has yet to be properly diagnosed or even existing (By Stihl ). It is a high frequency vibration within the saw.

@Corn-ped

Жыл бұрын

@@thomasgronek6469 hmmm. I would think that has more to do with an unbalanced engine or part.

@thomasgronek6469

Жыл бұрын

@@Corn-ped Thanks.

What tou mean, that less oil increases power? I thought and heard its opposite to that..

@loganscott7129

5 ай бұрын

You heard wrong. Fuel burns better than oil, Adding oil is purely for lubrication it slows down a motor

@mrfixit705

4 ай бұрын

Lean is mean. lean fuel 👍 but will burn up the motor . More oil not to much more. makes more power . 4.5 oz oil to one us gallon works great on my honda af16 with 72 cc polini .

@mrfixit705

4 ай бұрын

More lubrication less oil burnoff from heat and helps "diesel" any leftover thats why you get more power with a little bit more oil 👍👍👍

What size bit was that from The set?

@Corn-ped

2 жыл бұрын

oh man I dont know. Its small. it fits into the ringland but doesn't hit the bottom.

Very interesting, what's the reason that you can't do this on a 2 ring piston?

@Corn-ped

2 жыл бұрын

The ports allow fresh fuel mix to go around the ring and cool the piston. If you use the second ring, it will stop the premix and wont cool the piston.

@Pigmaster6373

2 жыл бұрын

@@Corn-ped wouldn't you still have the advantage of the pressures getting behind the ring making a better seal?

@OnlyLifts.

Жыл бұрын

​​@@Corn-ped Would you do it also for a daily driver? I have 70cc polini minarelli vertical air cooled engine, 2t Yamaha Spy(CW50RSP). It produces around 10-12hp. So basically: Dellorto 19mm, polini 70cc with two rings, Yasuni R exhaust. Do you recommend doing this to a daily driver? Is there a big difference in piston ring servise interval?

@crashtestdummie67

11 ай бұрын

​@@Corn-pedI don't see the logic...it would still cool the upper part of the piston even with 2 rings...the top is the same...

Does this work for iron cylinders? Plz let me no I need to no looks really hard to do

@Corn-ped

6 ай бұрын

Yeah totally!

I assume you didn't drill a hole were you marked the first marke because the pin? That's why you said 7 holes. But there's eight. Thanks for the vid gunn try it on a couple I have while there apart

@Corn-ped

2 жыл бұрын

Yeah, don't do it at the pin

@steveZ1turbo

Жыл бұрын

@@Corn-ped so really , you making the same “ notch “ as the pin “ hole “ correct ? I’m trying to vision what I have to do … lol I was first thinking you drilled right through the piston . But then I see that you say “ notch “ so really you make it look like the top only of the pin hole

@Corn-ped

Жыл бұрын

@@steveZ1turbo yes. Only notch it to the back of the ringland. Do not go thru.

Do I drill through the piston or just make “dimples”

@Corn-ped

Жыл бұрын

you just make little notches on the top lip all the way to the back of the ring land.

@JohnsonPortWorx

Жыл бұрын

@@Corn-ped gotcha thanks

What if ya remove the ring from a two ring piston and try this?

@Corn-ped

2 жыл бұрын

Same concept!

@datrollface2863

Жыл бұрын

​​​​@@Corn-ped what about compression, will the single ring with the "dimples" seal just as good as two rings?

Would it be good on snowmobile application

@Corn-ped

Жыл бұрын

That's where I learned about it. From 50cc racing sleds

keep making videos like this please, im a beginner in bikes engine modifications and want to open my own bike's repair garage, so yeah really need to learn alot about bike engine because that is the harder part for me. tq😊 and im subscribed.

I broke my top piston ring ...Will the bike run with out it

@Corn-ped

6 ай бұрын

yeah it will run fine. I would swap that bottom ring up to the top.

So that pushes the ring tighter to the cylinder?

I have only side gapped my plug on the stock 50cc eaton bimmer3 I roll as my daily. Major difference.. 7-8 mph top end gain. Not a super fast bike to begin with but cruising went from 28-30 to 35 easily. Top speed gain similar at 45 mph up from 37-38. More importantly just finished my street build gas porting the 70cc kit i have and ill definitely side gap the plug too. Its already pretty ridiculous but I hope it it will run cooler with the pipe and carb setup I have. It was running 55 mph. Would like to see over 60 without soft sieze and I believe this will do the trick. Gas and fuel oil mix already "tuned"

@Corn-ped

3 ай бұрын

yeah man! Get that 60!!!

Do you go all the way trougt

@Corn-ped

8 ай бұрын

No. Only to the back of the ring land.

Oh wow. You weren’t kidding. So you basically drill a half circle in 7 spots flush with the ringland and only run one ring if two ring piston?

@Corn-ped

Жыл бұрын

yeah. you just put little notches on the upper ring land and run a single ring. you do NOT drill THRU the piston. Just lil notches.

I can’t even see what u did. Can u zoom in?

@Corn-ped

2 ай бұрын

I did post a photo in the community tab on my channel.

Need to give us an up close shot of exactly what you did I couldn't tell so that made this video useless to a mid mechanic but still not understanding what you just did so please show an up close shot when doing anything else like. 🙏 Thanks

Couldn’t really see what you were doing..

Would it not be even better to make channels all the way to the upper edge of the piston for even more gas flow around top of the piston?

@Corn-ped

11 ай бұрын

some people do that on 4Ts. I think on a 2t they might gum up quick?

@mikeford5106

3 ай бұрын

TOTAL BS !!!@@Corn-ped

Most rings behave like dikes until they go below the exhaust port

Been building engines 44 years laterally gasporting to stroke piston huuuuu hels cooling huuuuu. 1 that's done on 4 strokes that use thin low tension rings to help sealing nothing to do with cooling. #2 in 30 minutes then holes will be getting stopped up with carbon. 3 kinda worse for cooling on a twostroke you just screw up the purpose of sqish gap good vid just wrong type engine

Are there circumstances where you wouldn't want to do this?

@Corn-ped

2 жыл бұрын

Not really

Wusste nicht das unge auch tunt

DO NOT DO THIS MOD !!!

@Corn-ped

6 ай бұрын

Yeah? How come?