I just replaced my Alternator...which needed to be replaced. The idler pulley, and belt tensioner pulley, serpentine belt (the car has 125K miles) and I was looking at the power steering pump, for this mysterious noise!! Thank goodness I saw this video, you just saved me a ton of money, and patience!!

@BornHandy

3 жыл бұрын

Hope you got it changed without any problems.

If you don't change this pcv unit, the engine may begin to push too much oil towards the oil scraping rings on each piston, and all six of them may have too much oil to handle and it can burn on to the scraping rings, and then the rings will not be able to move freely, so the engine begins to use a lot of oil. Than it becomes a big job. The engine is good, but it's a modern low friction engine build, so oil scraping rings are a bit low, so not much can give. Hence the potential problem. Note: it is not always that this hiss can be heard; the problem can still arise. The sets where you only get a membrane and the small cover is not original parts, but aftermarket parts, that is not the same quality. Whether you will use it or not, is of course up to you. Also, change the oil frequently. NOT every say 20.000-25.000 km. But no sooner than say 8.000-10.000 km maximum. And always an oil filter too. Do NOT overfill the engine with the fresh oil. Kind regards.

Thank you for the video! My girlfriends LR2 started to whistle VERY loudly and I was able to diagnose and replace the valve cover thanks to your guidance. Cheers!

This video helped me replace the valve cover on my daughters LR2. Thanks man.

@BornHandy

4 жыл бұрын

Glad it did. Thanks for watching!

Hi Jason! Enter today is June 19th 2020 I just got done replacing this piece and it was all thanks to you I was able to save some huge money and it's making me feel proud about myself. Thanks for posting and helping that Community out. Keep up the good work and I wish you the best.

@BornHandy

3 жыл бұрын

Glad I could help!

Video made it easy to replace. Still makes a sound but nowhere near as bad. Thanks

Easy to follow and saved a bunch of $$ - Thanks v.much

Definitely the problem with my friends 2011 LR2. Pull the dipstick it stops. You can hear the vacumn suction also when u pull the dipstick past its o-rings. Thank you!!! You Rock

thanks for taking the time to put this fix on KZread. I had the same noise . Very easy fix and saved a lot of $

@BornHandy

2 жыл бұрын

Glad it helped. Thanks for watching!

@darrenparis1640

5 ай бұрын

@@BornHandy I have a leak just below that valve cover you took off. How do I fix

Hay thank you that is the noise that my lr2 was making, thank you very much ,you're video was very helpful.

@BornHandy

3 жыл бұрын

You're welcome!

DIY Rover Tech here. Having Owned Land Rovers for 25 Years, the Ford Derived - Non Air Suspension Equipped LR2/Freelander 2 is the Best Truck Land Rover has ever Produced. Same Issue. 312,000 Miles. This will be my 2nd time changing this. (did it first at 165,000 Miles) Listen People. If you follow the Oil Change and Maintenance Schedule and replace parts as needed, your Vehicle will run LIKE NEW as long as You Own it. Mine does. 27 mpg on Highway on Regular Gas, Cold A/C. No Check Engine Light, etc. The Secret? Drive it like it's Transportation and NOT A RACE CAR!!! Yes, I simply DRIVE THE SPEED LIMIT. Less wear on the Engine. LITTLE OLD LADIES ARE RIGHT!!!

THANK YOU! SAME YEAR SAME PROBLEM

Thank you for the video it help me a lot on doing it myself Thank you

wow! just what I need to fix my LR2.

Thank you great video! Do you have one for the same vehicle that shows how to replace the thermostat?

Thank you super helpful!!

@BornHandy

4 жыл бұрын

Thanks John. Glad it helped.

Awesome video. Thank you. do you recommend cleaning the gunk out prior to installing the new cap?

@BornHandy

2 жыл бұрын

I am not a land Rover mechanic, but here are my thoughts on it. That motor has ran just fine with that gunk up there for the last several years, and it is out of the valve train up there, so I left it. If you were rebuilding the motor anyway, sure thing. But only changing the valve cover, I would be afraid to spray something that would get into the head, and not be able to get it back out if I needed to. If that happened, a simple job just became a head gasket.... That is not an "official best practice", but probably a good rule if you're a back yard do-it-yourself mechanic.

@rabihbarakat6533

2 жыл бұрын

@@BornHandy thanks. Glad I asked as I’m definitely back yard DIYer.

Can you do video on changing oil sensor?

Bro have same issue and when i take out the engine oil gadge the sounds finesh i put it back sounds back i change the pcv volve same issue

What tool do you need

Are you sure that membrane and spring cant be replaced without removing the whole cover? Im on a diesel

@BornHandy

2 жыл бұрын

At least on this model, it wasn't possible.

@123pov9

2 жыл бұрын

@@BornHandy yea i managed to remove it with a flat screwdriver by twisting in on the diesel. Easy clean

Does that valve cover have a gasket?

Do You Still Have This Vehicle. I Have The Similar One I Need Some Advice

Me too

Is this a petrol or a diesel?

@BornHandy

2 жыл бұрын

Petrol

@nw8000

2 жыл бұрын

@@BornHandy Ah is different on a diesel

So you just put the new on and didn't clean out the sludge? Way to go...

@BornHandy

2 жыл бұрын

That sludge will be throughout the "dry areas" of the engine. Short of a complete tear down, it simply isn't possible to get it all. Also, I'm "a guy at a house", not a "mechanic at a shop". I'm simply not equipped to clean that stuff out the right way.

@stevenshepherd2874

Жыл бұрын

LMAO....that sludge doesn't just get cleaned out.... probably should know what you're talking Bout before you talk

With all due respect, I noticed you never ever showed show us your viewers how to remove the PCV Valve in the first place, being the main subject of your video. So I give you “0”

@BornHandy

10 ай бұрын

Except for the part where I explain the PCV is integrated into the valve cover 1:12, and then how to change the valve cover step by step, beginning at 1:20 - and by extension, the PCV is changed with it...