Another reason I just sold my disco and bought and old Toyota 😂 still love your videos guy’s. The only thing I miss about my Land Rover is the community... the Land Rover wave 👋 its like a group of people who have shared a traumatic experience, you have a tight bond! 😂

When designers come up with stuff like this, where service items are so difficult to reach, they should be prevented from ever working as designers again. Preferably by throwing them off a roof into a wood-chipper. Even worse, the designers of the LR3 should have been forced to own one for 20 years and carry out ALL the servicing and maintenance themselves. Maybe that'd be too sadistic though?

My tip, Always cut the belt gradually until it slowly releases the belt tension, do not release the belt tension by undoing the tensioner bolt, because as you get to the end of the thread, the spring tension can ping it off and break the thread lug off the cylinder head, best to learn from the mistakes of others.......😉 Great videos as always... .....thanks

You’re both such a great team together always bouncing off each other. Well done on such a difficult task, regards from down here in Australia 👍

I am impressed! Changing a timing belt using a camera needs a lot of patience and knowledge. I tip my hat to you Christian!

@tommy2wheels943

3 жыл бұрын

I second that 👍🏻 you the Man!

@marcellopasini

2 жыл бұрын

I second that 👍🏻 you the Man!

@SniemGoogle

2 жыл бұрын

I guess I have to forth it then

@imsoaring

Жыл бұрын

Not a timing belt. A drive belt for the high-pressure fuel pump. It's position is not critical

@owen8538

Жыл бұрын

I still can t understand how that was done look s like complete nightmare 2 do can t even see anything

That's like wallpapering your hall through the letterbox, 😂😂👍

@Vera_and_Christian

3 жыл бұрын

😅👍🙋‍♀️ Vera

Great video as always, thank you! You can save time by not undoing any ECU and TCM connectors. There is enough space when you remove the coolant pipe that runs across the engine, and the bracket that holds the wiring loom at the back of the engine. You can then pull the wiring loom towards you which creates enough space to get the belt cover out and replace the belt. I always insert the new belt tensioner first, easier to locate it correctly in its insert without the extra tension or presence of the belt. The new belt simply will slide over the tensioner when lifting it over the wheel.

@Discoworx

Жыл бұрын

Ive just started this job. Got the coolant pipe off and scratching my head. I'll try it this way, thanks.

Impressed and jealous of your setup, skills and natural demeanour. Well done!

Wife playing with the dog in the background and you working on your landrover with your son. Life dosent get better than that. All the best from uk

@Vera_and_Christian

5 ай бұрын

👍👌🙋‍♀️

Great video guys. Love the banter, puts a smile on my face.

Well Christian/Vera - I did the job yesterday (under a gloriously sunny warm Corsican sky unlike poor you!) and although my method varied slightly from yours, it was 100% successful, not even a bing or a bing and no spurious messages on startup! My 2 specialists refused (because it's too much trouble no doubt); & the LR stealer in Vannes had asked €2500 (Timing belt at same time with body off). The only other vid on YT showing the job is terrible and unedited. Your vid gave me a logical progression and saved me from working 'in the dark' which is often a confidence-breaker. Now it's done I'd say it's fiddly but not difficult. PS The coating on the toothed side of the belt is I believe fibreglass not Teflon. I had the same issue as you (break in the coating, which implies it's 'normal') but my belt is a Dayco (as was the installed belt). NB neither belt had a date or rotation arrow. Keep up the good work, brilliant channel ( the regularity is so important to subscribers as you know) and a major contribution to the Discovery community.

@Vera_and_Christian

Жыл бұрын

Wow, great job. I am impressed. 👍💪🙋‍♀️Vera

Best video I have watched all week! Thank you both :)

At 7.00min, Christian, we now see that you could have become an absolutely, brilliant laparoscopic surgeon. But if you had, we wouldn't have these wonderful videos that you make with your delightful wife Vera. Thank you.

Hilarious as always. Glad you switched to British mode...I was confused until then, but what makes it worse is in Australia it was upside down too!!!! Hahaha!!! Great video for a task i am glad was already done on my Discovery

@Vera_and_Christian

3 жыл бұрын

😂👍 Gonna remember that one for the next video 🙋‍♀️ Vera

We have a saying in our house that things are never really lost until mum can't find them. Well done Vera for finding that hose clip 👍great video again 🤩

@Vera_and_Christian

3 жыл бұрын

😅👍 and then Christian is angry at me for finding it instead of him 😂🙋‍♀️ Vera

@simon-mouse8739

3 жыл бұрын

@@Vera_and_Christian guys just wondering if you got my email re LR time stickers? Keep up the great work and videos 🙂

@Vera_and_Christian

3 жыл бұрын

@@simon-mouse8739 👍 But I get so many requests that I do them in batches. Yours is coming, I promise. 🙋‍♀️

@simon-mouse8739

3 жыл бұрын

There's only 7200 of us to write to 🤣🤣🤣thanks I'll keep an eye out for the email 😁👍

Do you ever get to a point in the job and start to think "why the hell did I even start doing this poxy job"?

@Vera_and_Christian

3 жыл бұрын

Only once, when he fixed the sound dampening with construction foam 😂👍. Even for me, it's always an adventure 🙋‍♀️ Vera

You Guys had us in hysterics, the best technical comedy duo ever...The format is brilliant 👍 PS...photograph the connectors before you disconnect them next time🤣 or maybe not..

@Vera_and_Christian

3 жыл бұрын

😃👍🙋‍♀️ Vera

Danke Christian... O vídeo, foi uma verdadeira aula de manutenção. Perfeito. Congratulações!! 😃👏👏👏👍👍

Excellent and entertaining video. You are inspirational and have given me confidence to work on my Land Rover. Well done !!!!!

Fantastic, you are so brave! Had mine changed at 100,000 miles by the same method using a specialist- LR wanted to do body off. I’m so impressed, even 10 minute jobs take me hours because of rusted parts, clips that go ‘ping’ across the garden and replacement screws and bolts that are the wrong size. I always end up bleeding too! Well done.

@Vera_and_Christian

3 жыл бұрын

😅👍 The actual repair doesn't really take that long. We have accuired a sortiment of nuts, bolts and clips suitable for the Disco. And most importantly our little clip plier. We should do a video about that. 🙋‍♀️

I love your video's! They say that Germans don't have a sense of humor... boy were they wrong! I have a Discovery2 and looking at your video's always inspires me and gives me confidence I can service mine. Thank you so much and keep it up!

@Vera_and_Christian

Жыл бұрын

That is so great to read. 😃🙏🙋‍♀Vera

Always a very good job and well documented, brilliant

You are a genius Christian. And you have a good apprentice too !. Only joking Vera. You are 50% of the team.

Another great video, becoming accustomed to the background sound of "hammer on anvil". Thanks for posting.

@Vera_and_Christian

3 жыл бұрын

😅👍🙋‍♀️Vera

Oh my gosh! I now know why you guys video these repairs. It’s so you know how to put your LR back together. 😂 I’m pretty sure my Landcruiser only comes with a timing chain. Well done guys

@Vera_and_Christian

3 жыл бұрын

😃👍🙋‍♀️ Vera

Great to see that you're fearless Christian and you have humour whilst in the middle of a wiring dilemma,, from Northern Ireland greatly appreciated thank you for the video,, here it would be raining,, best done under cover, ☘️☘️☘️☘️☘️☘️☔☔☔☔☔

@Vera_and_Christian

3 жыл бұрын

😅👍🙋‍♀️ Vera

Your amazing Christian 😀 Vera is so sweet too 😍 What a fantastic job that not many people would even attempt that job 🤣 Take care guys 😎🏴󠁧󠁢󠁥󠁮󠁧󠁿

@Vera_and_Christian

3 жыл бұрын

😃👍🙋‍♀️ Vera

this Channel is fantastic you and your Wife are an inspiration to everyone who wants to learn how to perform their own repairs to their vehicles instead of paying over the odds at a dealership. Really give me the need to buy a Disco 3 but i would need you to move to south Yorkshire in the UK to give me a hand when ever it breaks down or needs a repair :-)

@Vera_and_Christian

3 жыл бұрын

😅👍🙋‍♀️Vera

Christian I'm impressed your skills , nice video

Really informative video guys. Awesome work

Very enjoyable... thank you!

Hi Vera and Christian i take my hat off to you once again you are an amazing gentleman I did not think you could do that job without taking the body off. but you've proved this wrong yet again lol is there no end to your talents I bet your friend with the LR3 is happy he knows you 😁 you're the sort of friend everybody needs, keep up the good work looking forward to seeing the next episode take care. Ralph

@Vera_and_Christian

3 жыл бұрын

Hello Ralph, his car is still not running well. The air conditioning is not working and the brake lines are corroded. We fix one thing after the other. Glad you like the videos. They are a lot of work to make and we really appreciate your feedback. Thanks. Christian

An awesome video. Congratulations on a fantastic job. :-)

Christian.Vera,Fabian.)) have to say great video and presentation,really entertaining and wonderful German humour fantastic, keep these coming,))) from over the pond,)))🇬🇧😃

@Vera_and_Christian

3 жыл бұрын

😊🙏🙋‍♀️ Vera

If LR had designed that scuttle panel to be removable, that job would be so much easier! Congratulations on your Inspector Gadget extendible arms, with full axis balljoint elbows 😊🤘

At "wheeler dealers" they label the wiring so they know where they came from...or.. in a more modern world, take pictures. Again a real funny video good interaction with Vera!

@Vera_and_Christian

3 жыл бұрын

😅👍 Next time 🙋‍♀️ Vera

I have done it 😨 before 2 years......I can remember about blod fingers 😬 Thank you for allways nice documentation....and english lessons. Kind Regards Herbert 🍀

@Vera_and_Christian

3 жыл бұрын

👍😃🙋‍♀️ Vera

wow, what a mission. great work.

Great video again. I really enjoyed it. I notised you already got 7000 subscribers. Great job guys Erik

@Vera_and_Christian

3 жыл бұрын

😊🙏👍🙋‍♀️ Vera

Thnx again! Massive love and Respect ~

Jeez what a nightmare! well done Guys 👍

You did a great job Christian, I have done two now and have used Dayco both times and noticed the missing coating on both belts, so must be a manufacturing issue

@Vera_and_Christian

3 жыл бұрын

Hello JJ, ok thanks for the info. We got a replacement under warranty but it did not look much better either. I think we leave it alone. Christian

That tool is amazing for the heater hose I've got one my self

Impressive and interesting video thanks

never take the tensioner bolt out with the belt in place, it can strip the threads in the head , always cut the belt first then remove the old tensioner.

@Vera_and_Christian

3 жыл бұрын

Thanks for the hint - I did not know this. Christian

Many thanks for that. You helped me save so much time :)

Another informative and entertaining video! Waiting for when you purchase a Discovery 4 5.0L V8 petrol and walk me through the timing chains and tensioners replacement 😂Cheers from Canada.

@Vera_and_Christian

3 жыл бұрын

😃👍🙋‍♀️ Vera

Step 56 😂😂 another great video from you both

Your so brave Christian. I'm glad I get staff discount at Land Rover.

@Vera_and_Christian

3 жыл бұрын

That is so great. Btw, I always smile when I see your name, we just love Danny MacAskill, I am sure you know who I mean😃👍🙋‍♀️ Vera

@danmacaskill1319

3 жыл бұрын

I know who you guys mean. Very good on a bike isn't he

Vera is going to get a dog for sure now. Oh, and well done Dr. C! Over 7k subscribers now, very proud of you!

Before disconnecting plugs where possible label and draw a couple of arrows facing each other. Use 'AAA' on both sides of first plug/socket, 'BBB' on the next etc. If needed use paper labels tied on with string etc. Yes it takes a few seconds but will give a huge boost in confidence that all plugs are replaced properly and with the right orientation. Often it is obvious but as you get tired a little help goes a long way.

Great video 👍🇬🇧

I don't even need to do this (not sure I actually would!) but still always entertaining to watch! And appreciate the British edit! (being in NZ on a UK car tho!)

@Vera_and_Christian

3 жыл бұрын

😀👍🙋‍♀️ Vera

Another awesome video. Thank you for the sticker it arrived last week, I will send you a picture once I have decided where to locate it on Discovery 3. If you every fancy doing some international videos you are welcome to come to the UK and help me (teach me) work on my Discovery 3.

@Vera_and_Christian

3 жыл бұрын

😅👍🙋‍♀️ Vera

Great vid. Thanks! Making sure my upcoming Disco4 has all belts replaced :D. Ps, what was the response from Bosch?

British mode was so funny, is this because our we sit on the right (correct) side of the car lol

@Vera_and_Christian

3 жыл бұрын

😅👍 Next time, we'll introduce the Australian mode.🙋‍♀️ Vera

Vera for president... better than a foxhound!!!

I recently had this very belt changed on mine as part of a 144K (mile) service. Whilst I'm fairly sure they didn't lift the body, they did at least have the advantage of having much of the engine out of the way already to change the front belts, oil pump and water pump. I can see why it took several days.

@Vera_and_Christian

3 жыл бұрын

👍 It is most important that the job got done. 🙋‍♀️ Vera

Amazing! This is the next job I do to my Disco. And I have been putting it off for months. No more excuses for me!

@Vera_and_Christian

3 жыл бұрын

👍💪🙋‍♀️ Vera

Oh god, this made me feel as uncomfortable as some horror movies but well done for tackling this job

@Vera_and_Christian

3 жыл бұрын

Oh, that was nothing. I still have nightmares from the time we fixed the clutch on my Freelander 👍😃🙋‍♀️ Vera

Christian is a five-star mechanic 👍 . Have you thought about opening a workshop?🤣 A hug from Portugal.

@Vera_and_Christian

3 жыл бұрын

Hello Mário, apparently I am a good video editor. I can make a repair look like as if I actually know what I am doing 😂. Thanks for your comments 👍. Christian

Always funny to watch you guys, hope you topped the coolant up 🤔

@Vera_and_Christian

3 жыл бұрын

Yes, and he took the spare coolant bottle I keep in my Freelander. Have to get that one back . Otherwise I am going to be stranded 😳.🙋‍♀️ Vera

Thanks for another great video well done When I did this job on my D3 it didn’t appear to have as much space as you did to access the belt and struggled to do the job with my big hands One tip though it’s recommended to cut the old belt to get it off as unscrewing the bolt in the tensioner when it gets to the last couple of threads the tension still present can tear the last couple of threads out and you may have to take the body off to re-tap the thread Regards

@Vera_and_Christian

3 жыл бұрын

Hello Leslie, I also thought that my 2006 plate had less room than Fabian’s 2009 plate. But it might be my imagination. Getting the disturbing things out of the way with patience is the key. Thanks for the hint to cut the belt. Luckily this did not happen here. Christian

Lovely couple

you should have been a gynecologist ! 🙂🙂🙂 Well done ✔

@tadeuszzasepa3285

3 жыл бұрын

Yep, next time they will show how to do it through the exhaust pipe;)

@ZachBrimhall

3 жыл бұрын

🤣

@Vera_and_Christian

3 жыл бұрын

😂👍🙋‍♀️ Vera

Excellent helpful video. Do you think RHD Disco would be easier or harder with battery and harness connectors on LH side near the fuel belt?

@richardwilliams8667

3 жыл бұрын

Ha at 21 minutes your engine bay changes to the other side!!!

Hello, your channel is amazing. I love it. Can you tell something about plugs in 2.7 tdv6? Are there spark plugs easy to change or only glow plugs which I heard are horror to move and get to?

@Vera_and_Christian

3 жыл бұрын

We have had no problems with the glow plugs on either our Land Rovers yet. (We had our Freelander for almost 150000 km , and the LR3 for about 100000km ). As for the spark plugs, we only have diesel engines so I am not sure about the cost of replacing spark plugs on a petrol engine.🙋‍♀️ Vera

How do you remember all them steps, I'd love to watch you fix my discovery 3. 😊👍🏽

I can't believe how calm Christian was...I would have been uttering every conceivable profanity known to man.

@Vera_and_Christian

2 жыл бұрын

Oh, he is a very good editor 😅👍. And actually we would put all the swearing in, but KZread would ban us immediatly 😂🙋‍♀️ Vera

@albertdesalvo7273

2 жыл бұрын

@@Vera_and_Christian 😂😂...I'm glad I'm not the only one who curses when working under the bonnet😂. Looking forward to your next upload😊.

I think im getting lr3 soon and now you have definitely made my mind up ha love your clips Have you any ideas/clips 💡 on low compression thanks keep it up

@Vera_and_Christian

2 жыл бұрын

😃👍 That is great, but we have not had any issues with low compression so far, on any of the Land Rovers we have worked on 🙋‍♀️ Vera

@MrJimmyToner

2 жыл бұрын

Was owed by police for 160k miles now has 230k miles what dose Christian think' to buy or not to buy that is the question

Great job and new sub for you ;)

@Vera_and_Christian

3 жыл бұрын

Hello Alli, thanks and welcome to the channel. We post every Sunday at 6:00 pm German time. Christian

6 months i changed my front and back tensioner and oil pump. ( not me at service:) ) i saw the tensioners and belt was also same looking like new and was thinking service did nit change! But know i see that its ok :))))

@Vera_and_Christian

3 жыл бұрын

👍 That is good. There is no messing around with belts. I was stranded with my Freelander once 🙋‍♀️ Vera

Great video again guys, have you ever made a video on how to install a second battery in your Discovery 3 if so where can I find it please? Regards Chris. Thank you Vera.

@Vera_and_Christian

3 жыл бұрын

No, we only use a Goal Zero at the moment. But Fabian wants to install an auxillary battery with a managment system. So hopefully we'll be doing a video about it. 👍🙋‍♀️ Vera

Love your videos. Could you do a body off repair in the future? I'm curious how difficult that is :)

@Vera_and_Christian

2 жыл бұрын

Oh no way. Our main goal for content on this youtube channel is : to fix everything without taking the body off. Just to proof that it can be done. 😃👍🙋‍♀️

@moritzmittel5254

2 жыл бұрын

Thought so :) Let’s see how long you can stick to that ;)

Great job you all did, but how do you check that the timing is correct before fitting the new belt?

@Vera_and_Christian

3 жыл бұрын

It's not really a timing belt, it's the tooth belt for the high pressure fuel pump. Christian doesn't know what he is talking about 😅. So there is no timing to be messed up. 👍🙋‍♀️ Vera

Vera, keep him right please and you are right,freelanders are so much easier...

11:00 "Next week.... Ski jumping!"

I love your videos & I don't even own a D3, but Land Rover made the D3 far too complicated for me to work on. I like a 4x4 I can spend time driving rather than more time spent fixing it, that's why I drive an old 02 Discovery 2 & only give it a routine service once a year, & if anything falls off & it still drives then that part probably wasn't needed in the first place. Things went badly wrong for Land Rover after Germany sold what was once a great 4x4 off. If I had the chance to buy a new 4x4, then I'd buy anything but a modern LR. Have you ever considered doing a "retro" series of videos on a D2 or a real Defender?

@Vera_and_Christian

2 жыл бұрын

Well, we would have to buy one first. Since we don't really make any money with KZread, our content is mainly based on what we own at the time. Buying a car just for KZread content, we would need a lot more subscribers and, most importantly, viewers. But if that time comes, we would love to get a Defender. A Discovery 2 is most likely not an option because of emission standards here in Germany. We cannot drive one as a daily driver here in our area unfortunately. 👍🙋‍♀️ Vera

Hi Vera and Christian I am a car technician I love both of you are both very entertaining’ can I ask what Christian dose for a job ?’ I guess he’s also a car technician?’ We also get lots of land rover’s in at our garage and them always hard to work on some jobs easier than others’ keep up the good work you two’ I drive a Volvo XC90 as being an ex Volvo technician’ all the best Charles

Your wife is a saint. How she puts up with you but maybe it’s because you two are Land Rover owners. :).

@Vera_and_Christian

3 жыл бұрын

😊👍🙋‍♀️Vera

Hi! What a great video, thanks again and again. But One question, though : Have you ever changed the rear crankshaft seal just behind the big fuel pump pulley? I have to do mine as there's a big leak that was a part of the causes that ruined my crankshaft bearings, lacking oil pressure.

@Vera_and_Christian

2 жыл бұрын

No we have not, thank god. The rear crankshaft seal is on the gearbox side, so the gearbox has to come off. 👍🙋‍♀️Vera

@davidf.8497

2 жыл бұрын

@@Vera_and_Christian I was meaning the rear camshaft seal ;) Sorry !

You makes the jobs looks easy, infact it's not for beginner like me...... Lol

@Vera_and_Christian

2 жыл бұрын

😃👍🙋‍♀️ Vera

have you ever attempted the crossover exhaust pipe at the back of the engine , under the the belt you just replaced

@Vera_and_Christian

3 жыл бұрын

No, not yet.🙋‍♀️ Vera

Are you the most popular man in Germany for any one why drivers a landy Excellent job and excellent content

@Vera_and_Christian

Жыл бұрын

Maybe, I do get asked every week at least once if someone can come bring their Discovery by.. 😅👍🙋‍♀️

fantastic video how did you manage to fit that belt ,as always I would never buy one of them but great video do you need to time that belt

@Vera_and_Christian

Жыл бұрын

Ont the 2.7L the belt is not timed. On the 3.0 it is. Much more difficult. Christian

another great job well done 👍. I saw you used the tube camera a lot, looks very useful, what it is called? do you have the Amazon link? thanks

@Vera_and_Christian

3 жыл бұрын

I bought this one www.amazon.de/gp/product/B08HCRQTKD/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1🙋‍♀️ Vera

@davidhk001

3 жыл бұрын

@@Vera_and_Christian thanks

Hi guys, once again, great video and brilliant team work, I think Vera has the most important job, finding lost parts! ...could I please ask what make of camera you used? ...would Vera be available when I do my belt, I've no doubt I'll drop something 😲😲 ...again, thank you for your videos 👏👏👏 Regards Norm's with UK Disco 2, 3 & 4, you have to love a challenge 🕺🕺🕺

@Vera_and_Christian

2 жыл бұрын

🤗We use the DJI Osmo Action only. 👍🙋‍♀️Vera

@normanwalker-worth3039

2 жыл бұрын

@@Vera_and_Christian Hi Vera, thank you for you message, I will look it up after I finish watching Christian and his smoke machine on your Disco 3 ...you need a little chimney on your bonnet, and this would look good as your driving 👏👏👏👏

You need to get a harness that will support you horizontally over the engine in any orientation you choose. So many times I've seen your feet sticking out - it must be painful experience laying there for hours on end. Shouldn't be too hard to build using x-y table from a suitable cnc.

Ciao Fabian!!! Perfavore volevo sapere, cavaleti de alberi camme quanti Nm vengono streti? Per la cinghia distribuzione pompa alta pressione ho fatto anche io uguale!!! Grazie, molto bravo BRAVO

Great video guys, i am impressed, i have a question lets say the belt just snapped, do you need to time the fuel pump when replacing that belt or it is not timed, thanx

@Vera_and_Christian

2 жыл бұрын

Only the 3.0L is timed. The 2.7L is not. Christian

@westermanjengwa7375

2 жыл бұрын

@@Vera_and_Christian noted,thank you.

Those white electrical plugs are clearly a German design 😂. Far to fancy to for us Brits lol. Brilliant as ever. I kinda want to take the body off though.. just because. Lol

@Vera_and_Christian

3 жыл бұрын

Yeah, Christian too, and I am having nightmares about it. 😂🙋‍♀️ Vera

Where would I be able to get that camera and the lighted magnet wand that you used?

@Vera_and_Christian

3 жыл бұрын

The endoskop camera, I got from Amazon. It connects via bluetooth to your cellphone, about 30€ ; the magnet is from Aldi, available only once per year 😢 🙋‍♀️ Vera

How long did this take? A great video. Make me pleased that I have a D2

@Vera_and_Christian

3 жыл бұрын

Without screwing around, filming and loosing stuff this is a 3h first-time job. We took 4h and I think as a repeat I would need no longer than 2 hours. Christian

Hey, what's the name of the camera you used to see the timing belt?

@Vera_and_Christian

3 жыл бұрын

It's an endoskop camera from Amazon for 30€ which connects via bluetooth to your cellphone. I will finish our Amazon link list this week hopefully. 👍🙋‍♀️ Vera

It’s LR Time!

@Vera_and_Christian

3 жыл бұрын

😅🙋‍♀️ Vera

Christian /Vera. Just seen this, what did they say about the timing belt? I am pushing eighty so don’t know about these other channels . All the best from England .

Did the €4000 “fuel pump fault” error come back since the filter was replaced?

@Vera_and_Christian

3 жыл бұрын

So far not 👍🙋‍♀️ Vera

4:44 I'm shocked - so far it's most German thing which I saw))

Can you tell me what is the red heavy duty wire for ??

@Vera_and_Christian

2 жыл бұрын

That one is connected to the winch. It's not part of a stock Discovery. 👍🙋‍♀️ Vera

Use spring type hose clamps for hoses those screw ones are bad news especially on plastic that has large heat expansion, I believe the screw ones are banned in aviation.