Land Cruiser Front Brake / Bearing Replacement E70
Тәжірибелік нұсқаулар және стиль
In this video I replace the front wheel bearings, rotors and brake pads on my Land Cruiser / LX470. I made sure not to skip any steps and include all tools required as well as torque specifications. If you need a detailed how to video for replacing your Brake Pads, Rotors and Wheel Bearings, this is the video for you!
#1 - AllDataDIY
bit.ly/2nW6dCT
#2 - Snap RIng Pliers
amzn.to/2nPHznm
#3 - 54mm Axle Nut Socket
amzn.to/2nhnqGh
#4 - Front Rotor
bit.ly/2naPXxo
#5 - Portable Workstation
bit.ly/2mlEQBw
#6 - Inner Wheel Bearing
bit.ly/2lB9Ay8
#7 - Outer Wheel Bearing
bit.ly/2nRAliR
#8 - Rear Axle Seal
bit.ly/2lCrH6P
#9 - Bearing Race and Seal Driver (with 72mm and 89mm)
amzn.to/2miGcgw
#10 - Spring Tension Guage
amzn.to/2minEgp
#11 - Brake Pads
bit.ly/2lGU3wU
The links above are affiliate links, we receive a small commission for these, but you don't pay any extra.
Пікірлер: 50
Make sure if you do this job you have a Bearing Race and Seal Driver big enough for the inner bearing. It is just under 90mm, so an 89mm or 3.5" driver would be perfect. The only kit I could find that had drivers this large is this amzn.to/2miGcgw
Thanks for taking the time to list all the parts and tools with sizes, new subscriber.
Shout out to the guys/gals that make DIY videos with parts list in the description. You guys rock. Thanks for the video.
@shaweehillsworkshop4226
4 жыл бұрын
Eugene Koval thanks for watching. I really wanted this video to be helpful and am glad that it seems to be! Good luck with your project!
Excellent video, thanks for posting. Just did my brakes and bearings today using this video as a step by step. My major hold up was with the cone washers. I had to use spray penetrant a screw driver and a hammer for about 45 min each side to get them all off. Thanks again!
@shaweehillsworkshop4226
2 жыл бұрын
I’m glad it helped
Generally you can tap the bearing races in with a round drift or bar, made from a softer metal than the races. Also just in case people don't know. Before you press the pistons into the callipers make sure your brake master cylinder isn't to full of brake fluid, otherwise it may overflow onto the paintwork. And when finished pump brake pedal until you get a firm pedal. But a very good video.
Just did my front bearings today. This video made the process very simple, thanks for making it!
Thanks for the solid video. Helped a lot when doing the bearings on my comparable landcruiser. Good enough that I'll just link to your video rather than duplicate it.
Great video buddy!
@shaweehillsworkshop4226
4 жыл бұрын
Thanks man!
Great vid brother!
You got lucky with those cone washers. Good job.
good Job Shawne
Fantastic, thank you for sharing, if you can share the outer bearing parking, that will be great.
Thank you!!
Do front axle swap next without removing hub. This will be a great resource.
Wesley, great job but you forgot a very important step, which is to grease the needle bearings inside the spindle and the brass bushing on the backside of the knuckle. I'm also a fan of the fish-scale method for final hub nut torque because it ensures proper preload regardless of the age of your bearings (older, but still usable bearings require much more torque than you would think) but that's less of an issue with new bearings. Thanks for uploading!
@shaweehillsworkshop4226
4 жыл бұрын
Brian Escamilla good call in the needle bearings! I will make sure to do that this weekend! I agree on the fish scale, I have purchased one now so I will have it in the future. I’ve seen guys have to go to 40ftlbs to get 10 lbs of preload on old bearings before.
Fantastic.
Thank you
@shaweehillsworkshop4226
4 жыл бұрын
Glad I could be helpful! Thanks for watching
Great video. But only one nut mentioned on assembly
Shawnee, great video. I will have to do mine this spring. I will use this video, instruction and parts recommended. One questions, is the procedure the same for rear wheels? I have done breaks before, but has not replaced bearings. Thanks in advance. MR
@shaweehillsworkshop4226
4 жыл бұрын
I haven't done the rear bearings in a 100 series before, so I honestly can't say. It would probably be worth looking into all data to make sure you know what you're getting into.
Thx
good way to keep from going broke when you change your brakes before they break good job :)
@shaweehillsworkshop4226
4 жыл бұрын
Lol
What is the outer nut torqued to?
How's the koyo bearing going so far with you?
I don't see my 2006 Toyota Land Cruiser on alldatadiy.com? Is the LX470 the same specs?
Your link for description #2 isn't the same snap ring pliers. I have this small blue Irwin. You were using a big red one. Can I have the info on it?
@shaweehillsworkshop4226
2 жыл бұрын
I was using one from an icon set from harbor freight. It’s an 8 piece set that runs about $70
Hi I live in europe place where we use kilograms and milimiters kilometers. I like your video but we use NM in torq renches :) have a nice day
May I ask the size of your BFG AT tires? Thank you.
@timadamany
4 жыл бұрын
Are they 275/70/18?
I don't see our vehicle on alldatadiy. How were you able to purchase from there?
@shaweehillsworkshop4226
4 жыл бұрын
what vehicle do you have?
@EBlueEm1
4 жыл бұрын
@@shaweehillsworkshop4226 2005 lx470
@shaweehillsworkshop4226
4 жыл бұрын
Rockey Vue look under Lexus trucks. Lx470 should be listed there
@EBlueEm1
4 жыл бұрын
@@shaweehillsworkshop4226 I followed the link in the description..im not sure there's an option for that on there. It just asks for the year make and model on the drop down menu when you try to look for the vehicle. Unless you can direct me to where that option would be when you enter the site?
@shaweehillsworkshop4226
4 жыл бұрын
Rockey Vue yes, on the drop down menu for make, don’t choose “lexus”, right below that is “lexus truck”. Then it will give you another drop down menu. If you still have trouble email me at shawneehillsfarm@gmail.com and I will email you screenshots
Maaf ya allah hamba liat ini.
Omg.