Lamborghini Countach 3D printing design, print and assemble.
Автокөліктер мен көлік құралдары
STL- fab365.net/items/421
I have expanded and applied my design style to various objects. In particular, many attempts have been made in automobiles, and what has been achieved so far is the supercar.
The reason is that the shape of the supercar is flat and the shape is very complicated. When the shape is flat and complex, it is difficult to put a structure into it.
However, I decided that I could not postpone it any longer, so I took on the challenge this time.
I couldn't try too difficult form from the beginning, so I chose the relatively low difficulty Lamborghini Countach.
As mentioned earlier, the car was too flat, so I chose the car's scale to be a bit larger, 1:24.
The biggest challenge in this design is, above all, the construction of the scissor doors. After several attempts, Scissor doors were created.
Because of the large scale of this design, I managed to reproduce all the opening and closing devices that I could not try in the 1:38 scale that I had previously designed.
This design has a lot of parts, so there are a few precautions when assembling.
1. Make sure that the left and right of the scissor door hinge is not reversed.
2. The width of the front and rear of the tire is different, so check this.
3. It is better to install the front window after assembling the upper and lower body. Otherwise, it is difficult to identify the projections and holes that connect the upper and lower bodies. The front window can be inserted easily by assembling the upper and lower bodies of the Scissor doors, then opening and pressing the Scissor doors.
4. When attaching the front bumper, glue should be applied only to the projections. If applied to other areas, the hood may become stuck and not open.
For more details on the assembly process, please check out the video.
While this attempt was completed, the existing folding structure was considerably abandoned, and there were many parts to assemble and attach. that's a bit disappointing.
However, if the response of this design is very good, I will try to design more supercars in the future, reduce attached parts and apply my design style more to pursue new fun of 3D printing.
1 : 24 Scale
Largest part in printing, size = X 55mm, Y 170mm, Z 70mm, After full assembly size= X 82mm, Y 172mm, Z 46mm
Total Build time : 46h / Plastic weight : 164g
Пікірлер: 43
these are getting more and more complex, looking forward to the testarossa, whenever that gets made
@fab365_official
Жыл бұрын
Thank you~ If the sales of Countach are good, you can also make Testarossa. Expect good sales.
That's incredible. The flip up headlights have a print in place hinge. Everything under the front and rear lids and inside the doors gives a whole new level of detail. I will tell you that I prefer the option of printing and assembling a high detail version for myself or a 'playable' version of your models for my nephew. For example, I could glue movable parts down and not print the smaller parts. The videos and the assembly advice are much appreciated.
@fab365_official
Жыл бұрын
Thank you very much for watching and comment! I hope you and your nephew like my countach.
Its more complicated, but its beautiful....
@fab365_official
Жыл бұрын
Yes, it is. Thank you~
와...제가 차를 엄청 좋아하는데 문도 열리고, 트렁크도 열리고..굉장히 디테일한 차네요! 오늘도 잘 보고갑니다!
@fab365_official
Жыл бұрын
좋은 댓글 감사합니다!
Impressionnant :)
@fab365_official
Жыл бұрын
Thanks for watching! Please enjoy!
thats the best version of the countach, tbh.
@fab365_official
Жыл бұрын
Thanks for watching~ Please enjoy~
You should make the hardcastle & McCormick coyote car next.
Quite impressive!
@fab365_official
Жыл бұрын
Thanks for watching! Please enjoy~
Smart design!
@fab365_official
Жыл бұрын
Thanks for watching! Please enjoy~
Nice!
@fab365_official
Жыл бұрын
Thanks for watching! Please enjoy~
Are you guys going to add any extras like the other vehicles? A spoiler or intakes to mimic Sideswipe or Sunstreaker from the Transformers would be perfect! grabbing this model now, best Countach out there!
que bueno que está! sos un groso! felicitaciones por tu trabajo!
@fab365_official
Жыл бұрын
Thanks for watching and comment~ Please enjoy~
PERFECT. YOU ARE STARTING TO OVERCOME YOURSELF. IT HAS ARRIVED TO THE LEVEL OF READY MODEL KITS. I'M SURE IT WILL BE MORE DETAILED SOON
@fab365_official
Жыл бұрын
Thank you very much for your good comment!!! I will do my best~
Awesome design! Would be awesome if you had Bambulab printer profiles. Parts are loose when I snap them together and am experimenting with different settings but not there yet.
Guau!!!❤
@fab365_official
Жыл бұрын
Thanks for watching! Please enjoy~
Really nice detailing. Plz mention which application is used for designing .
@fab365_official
Жыл бұрын
Thank you~ I used Rhino 3D for design. Please enjoy~
이러다가 무르시엘라고도 만드시겠어요ㅋㅋ
@fab365_official
Жыл бұрын
잘 팔리면 만들어야죠! 감사합니다!
@Robert.1.0.1.0
7 ай бұрын
how much would it cost you to build a model lamborghini?
Cada vez q quiero imprimir por partes las piezas después no me encajan y cuesta q coincidan del todo bien 😢
Can you make toyota supra mk4
@fab365_official
Жыл бұрын
Could you ask or vote on my request page please? fab365.net/requests Thank you~
Can you make white version with Lance guy?
@fab365_official
Жыл бұрын
Could you ask or vote on my request page please? fab365.net/requests Thank you~
Missing the rear wing dude.
lp-500 next ?
@fab365_official
4 ай бұрын
Could you ask or vote on my request page please? fab365.net/requests Thank you~
😚 P r o m o s m
Wow absolutely amazing. I’m still struggling with bed adhesion. I have a long way to go🥹
@fab365_official
Жыл бұрын
Thank you~ Please use this bed. www.shop.fab365.net/energetic If you apply hair gel on it, adhesion will be better. www.amazon.com/Gatsby-Styling-Super-200g-molona/dp/B000FQOOT2/ref=sr_1_27?crid=RER09KIADNQJ&keywords=gatsby+hair+gel&qid=1687506580&sprefix=gatsby+hairgel%2Caps%2C268&sr=8-27