That is the nicest jeep I have seen in years you did a hell of a job sir 👏

@BuyFixFlip

Жыл бұрын

Thank you sir that means alot!

I was wondering about the idle myself, and personally I think I would put some more time in engine mounts and go for a lower idle. The high idle would drive me nuts quicker than a little more vibration. Still a great build and I wish I could do something very similar. Thanks for sharing this with us!

@BuyFixFlip

Жыл бұрын

Yeah I will be looking into it more this winter I just wanted to enjoy it for the summer! Thanks brother.

@mattbranstetter4072

Жыл бұрын

I have been running my '46 CJ2A swap for 6 years now. I have the same issue with the idle. I have just accepted the 1200 rpm idle at this point. Nice job!

man that jeep is perfect. great work!

@BuyFixFlip

Жыл бұрын

Thank you!

that's a cool build; good post apocalypse vehicle too. They used to advertise those surplus jeeps all the time in the back of magazines when I was a kid in the 80s. That'd be a very fun summer vehicle for tooling around in too. great project idea.

This is the video I was looking for on these V2203 swaps, lots of videos of first starts and parts collections but not much of the nitty gritty. Super cool. Once I get some more space cleared I'm looking to pick one of these up for a project.

I've really enjoyed watching everything that you have done to your Willys jeep. Cannot wait to see additional videos of it in action!

@BuyFixFlip

Жыл бұрын

I'll be taking it out tomorrow so stay tuned, thanks for the kind words!

As a former OTR driver pulling reefer, the sound of that engine lulled me to sleep many a time. Unless I was pulling a frozen load and then the engine would cycle off/on at higher rpms. People hated us reefer drivers at the rest areas and truck stops.

@eddaniels3404

Жыл бұрын

That was me i cant stand the Rev

Wow, these two Jeeps are awesome , love how they sound !

I love this setup! As far as the speed goes, it really wasn't much faster with the OEM gas engine, so no real loss there.....

Great video with good information! Thanks for including the real audio instead of loud music like everyone else on KZread.

Nice setup. Definitely go for that T98 swap, you won’t regret it with that 6.40:1 first gear. Total game changer!

@throttleblipsntwistedgrips1992

Жыл бұрын

As someone who owned a 6.68:1 1st gear, I can confirm this.

Diesels are supposed to vibrate, and big semis do to its just how they are bro and its bad ass cool leave it at the low idle you will come to get used to it!!! and thanks for showing us the jeep again and showing us how it drives which I kind of had an idea because they can go everywhere but once again thanks for listening!!!

Always thought the YJ with a VW tdi swap was cool. But this is freaking sweet. Would be a perfect farm toy too

I have a 64 CJ3B that I haven't gotten into yet. If the motor is gone, I'm definitely doing a diesel swap similar to this. I have a small ranch in the San Diego mountains, and some OHV trails out my back door. This vid really inspires some great ideas, thanks.

Have you thought about using a thermostat that lets you run the engine between 180 and 195 degrees Fahrenheit?it would probably increase your mpg as this is the optimal temp for a diesel to run.

Awesome!! Great job!

Great video and awesome jeep, the only thing I gotta say is please if your gonna off road, build yourself some kind of simple cage or even head loops like the old corvettes had. You and your buddy going up those hills could have easily been a bad day if you rolled or flipped. Also get yourself a 5 point harness...c'mon man...otherwise sweet video and build.

@trjb1767

Жыл бұрын

God save the queen

Thats a sweet setup! Enjoyed the QnA.

Great video and great project! I have owned a kubota L3010 since 2009 and have worked the crap out of it with no problems. I also have a JKU rubicon and previously had a CJ7 so I can appreciate the Jeep angle too. Would love to do a project like this someday. Thanks amigo!

@rediron44

Жыл бұрын

Just put in a Jeep 4.0 inline 6 in it. Run 300k and you can run the interstate

In the middle of 5cyl TD Mercedes om617 into a65 CJ6. Wish there was a kit for mine, but yours looks real good…

@BuyFixFlip

Жыл бұрын

Thanks man! Good luck on the swap!

I too have the Kubota swap. I took my radiator in and had them swap out the bottom exit tube and made it come out straight so now it takes a 90's hose into the motor.

I'm no youtube expert (and i hate them too). That being said, you do need to have your engine running at least 140 degrees for a prolonged period in order to burn off the moisture in the oil. Oil gets contaminated with combustion byproducts and turns into a mild acid. This will eat at internal components like valve springs, etc.

I would choose the lower rpm, it sounds much cooler! Nice conversion! 👍👍🎉🎉🎉🎉🎉🤘🏻🤘🏻

Very cool 😎 thanks for the video 😎 👍 🇨🇦

@BuyFixFlip

Жыл бұрын

Thanks man!

Sweet machines, great engine swap idea.

Awesome build, awesome video

@BuyFixFlip

Жыл бұрын

Thank you!

You should put in a thermostat to get your temps up to ~190. This will boil off the water in your oil and greatly prolong the life of your engine

Sweet build.

I need one, my only question is where am I going to get the money, dang it it’s always something. Great machine brother ✌️🇺🇸

Team Kubota! Nice work!

My new favorite channel, they jeep is badass, great job

@BuyFixFlip

7 ай бұрын

I've been slacking on KZread lately hopefully you will like the 6x6 kubota jeep I built!

Awesome machine.

So cool. I paid over 5K US for my Toyota 1KZTE half-cut with 28K Kilometers on it so that's a crazy good deal for a diesel. I own 2 Kubota tractors (a BX and an L series, both 4wd), their engines are VERY reliable. They're basically the Toyota of the tractor world.

Those donuts looked more fun than anything I’ve done in years

Last week’s video was my first time on your channel so I sub’d , love this video answered all my questions from the last one. Big difference in this weekend then last huh I am a buckeye too.

@BuyFixFlip

Жыл бұрын

Thanks for coming back for this one! Also you can say that again! It's gonna be 62 on Tuesday, Ohio is sure something this time of year.

@Manandmachine772

Жыл бұрын

@@BuyFixFlip like they say just wait 5 minutes and the weather will change. Your Jeep reminds me of my old flat fender it was a 48 and it was orange too.

Love the black smoke from the tailpipe

@BuyFixFlip

Жыл бұрын

me too!

Cool build

The vibration is going to eat up the poor thing. Your electric fan is fine, but in my “professional “ opinion you need to get the engine temp up to at least 190 degrees.

Your other option with idle speed would be to turn the fuel delivery down JUST a smidge. I bet you'd be able to find that 900 rpm sweet spot...

VERY COOL !! I want one !! Brent Glendale Az.

First things first. Order a Dayco belt. Period. Anything else is a junk rubber band. I would try to get it in the design that is NOT a top cog, for this application. Once you determine the length, order two more. One to keep in the Jeep and another for stock in your shop. Remember, two is one, one is none. This applies in most cases in life.

Nice jeep, good video. Diesel burns les hot more torq 👍. Greetings from the netherlands holland.

So back in the early 90s I bought a CJ2a from a bar owner in Sebastion Fl, he used the thing late at night driving up n down the beach. I paid 400 for it stripped it down and put a Ford pinto motor in it out of an aircraft tug best CJ2A I ever had it ultimately completely sucummbed to the beach runs but I hammered it for years it was a very good rig if you paid attention to all the little things.

@BuyFixFlip

Жыл бұрын

Great story! Thanks for sharing!

I’m in love with this jeep

@BuyFixFlip

6 ай бұрын

It's coming back home tomorrow!

@colbycramer1214

6 ай бұрын

@@BuyFixFlip is that an original body on yours?

@BuyFixFlip

6 ай бұрын

Yes sir!

I love this thing !!!!!!!

@BuyFixFlip

Жыл бұрын

Thanks man!

@justinsmith847

Жыл бұрын

You are welcome I really do like it that body style jeep is a bucket list vehicle for me one day I'd love to have one and this diesel swap to me makes it perfect really great thanks for sharing

That thing is awesome

There's old reefer unit they do like to stay at a nice constant idle kind of a high idle too because that's made to run a refrigerator unit I remember when I pulled them if there was any dirty fuel or or a dirty air filter that would cause it to idle differently you could instantly tell

Great job and a perfect set up. My Isuzu 3.9l has the same idle issue. Lower it and it will shake the truck to pieces, put it up a bit and it smooths right out.

@BuyFixFlip

Жыл бұрын

The tdi guys have showed a hollow motor mount that helps alot. I'll be trying it soon!

@jdenmark1287

Жыл бұрын

@@BuyFixFlip curious to see what it does. My Isuzu is original in Land Rover Perentie and has stock mounts which as I understand are HD to keep the engine and transmission from tearing loose.

@ricvibesinc1

Жыл бұрын

@@jdenmark1287 Would love to see a vid of your rig .. man ...

@Fulcrum205

3 ай бұрын

​@BuyFixFlip its 4 cylinder thing. They are all shaky at low RPMs. You could probably fab up a puck type mount with some urethane or rubber body mount pucks and something a little squishier like neoprene. You need 2 different durometer materials to damp the vibrations

Nice video

Great video……I want one 😊

@BuyFixFlip

Жыл бұрын

Thank you!

Great set up. My issue is with the small meager Air filtration set up! Diesels really need clean Air& fuel.(as u probely know.) Just my 10cents .Cheers from B.C.Canada Eh!

@BuyFixFlip

Жыл бұрын

That will be taken care of when I take it all down and put it together right. We were in a hurry to use them this year and smacked them together quick.

That looks like an engine and drivetrain worth protecting with Amsoil lubricants. I use some and it works very well. I also use some Triax lubricants which are excellent as well and less expensive.

@BuyFixFlip

Жыл бұрын

I do love using amsoil in alot of stuff. I am a firm believer in good oil. Currently I'm running Rotella T6 in it.

Would love to see more videos of you crawling and off roading in it! Awesome build, super jealous

@BuyFixFlip

Жыл бұрын

There will be plenty in the spring. This time I will make sure they video me first!

COOL!

My uncles brother had one same color , must have been forest ranger colors as his father was a game warden/ sheriff, his had a Palmer 4 cyl engine

Better get a roll bar climbing those rocks

Gotta love old flat fenders. What you built looks and runs great. What are your plans for stopping. I own a 53 CJ3B for a while, it's lack of stooping power was legendary/scary. Good Job!

@BuyFixFlip

Жыл бұрын

It has a full sidekick disk brake conversion on it!

Sweet Jeep kubota swap! I'm liking the way it works and have a plan for a Commando. I'm only one old man with too many projects, so we'll see how far I get. Thanks for the informative video, Jeep on my friend!

hi there i believe those are the auto hubs cluch in them may be something to look at , , i am putting a set of 373 rears in my 51 , took the pill out to the t/c . i now start in 2 wheel low then 2 wheel high then 2nd and 3rd m might be a thought , you did good john

@BuyFixFlip

Жыл бұрын

I wish that was the case I swapped the locking hubs already, sound still there. New video coming soon of the front end rebuild

@fricknjeep

Жыл бұрын

@@BuyFixFlip looking forward to it

On the idle try slipping feeler gauges in between the stop and the arm. See if you can fine tune that

Hello fellow Ohioan! Dude, that Willys is SUPER sweet! I wish I had more time, I'd love to consider building one... Looks like a fun swap! I'll be checking out your other videos. Are you planning on building more of these? I bet you could make a few bones selling them.

@BuyFixFlip

Жыл бұрын

Thanks brother! Also I'm not sure about building alot of them. It's hard to find clean jeeps these days. I am planning on diesel swapping my 6x6 though!

4:04 My company has a couple of those engines over 50k hours in carrier reefer units. That's 50k engine hours, not unit hours. The units have well over 60k. They get an oil change once a year, probably every 3-4k hours. I'm waiting for one of the units to break badly enough where I can buy the engine for a swap.

I just found a J-53 diesel. Probably not as good as what you've got here, but still pretty damn cool.

set it at 900rpm that is about where its suppose to idle yes it is very sensitive a hint slightly tighten jam nut and move the idle screw just a hair at a time then lock it down completely when get it at 900-950 rpm.

I must own this jeep. It would compliment my tractor perfectly. This is the only jeep I would consider giving up my lj for.

@BuyFixFlip

Жыл бұрын

They are a hoot, you could probably build one for around 10k if you get the body for a decent deal.

@Miniscapes515

Жыл бұрын

@@BuyFixFlip I'm already on it. Been pricing out stuff and searching g for a good tub and frame since I seen the vid.. lol. I had no i dea putting kubota engines in old jeeps was a thing but I am hooked.

@BuyFixFlip

Жыл бұрын

@@Miniscapes515 feel free to join the Facebook group and ask away. We are glad to help!

2 remarks: running hours depends on use i think. When full hp was used or not. Rubber boat dempers are designed to reduce vibrations. Tried those? There was a special series landrover ,,lightweight,, 88 with a 2,25 liter diesel. Built for the dutch army. Series 2/3.

@BuyFixFlip

Жыл бұрын

Yeah I'm looking into multiple hollow options for the mounts!

@henkoosterhof5947

Жыл бұрын

@@BuyFixFlip a company called vetus have special designed dempers for engines with lot of vibrations fir example 3 cyl units.

Cool

some perkins diesels will bolt straight up to a ford ranger/mazda transmission.. no need for adapters

Its like a legit Mahendra roxer

I'd take a Kubota swapped flat fender over anything built by Chrysler.

@BuyFixFlip

Жыл бұрын

I feel that!

@johnossendorf9979

Жыл бұрын

@@BuyFixFlip Deep Down !

Jeep power

I like The Jeep🙋👍🤗✌️🇵🇭

@BuyFixFlip

Жыл бұрын

Thanks man!

What was the final sales price of your jeep? Saw it listed on EWilly's and it was already gone! Such a sweet jeep

Great job! I have a friend with a ford tractor that does the same thing when idling down. I suggest it may be a miss from a bad injector or valve?

I need to get me one of those

Do you like your tires? What brand are they? Great little orange jeep. I drove one in the army.

i used to have a 68 willis jeep

I was thinking a new venture nv4500 5spd od would be cool, if ya could find one, they're kinda rare and expensive. Alternatively a nv3500.

Mannn I'm itching to do a Sammie swap now. Awesome thanks! Any plans to add a roll bar?

@BuyFixFlip

Жыл бұрын

Do it! I'm in the same boat I love them! Also not too sure yet. I would love to but then I would probably want to add seat belts etc and I don't know what I'm wanting to do yet.

I wonder if your harmonic ballancer/crank pulley is out of phase. Robot Cantina removed his ballancer and put it on wrong and had the same kind of shake.

@BuyFixFlip

Жыл бұрын

I never removed my crank pulley. Most people that have done the swap have the same shake. I'm going to switch to hollow motor mounts

you can try shortening the hose a little to shift it out of the danger zone.

@BuyFixFlip

Жыл бұрын

The angle it makes wouldn't be possible with it any shorter. I'm gonna get the shorter belt!

Im fairly certain the smoke is lost power. I think its basically just unburnt fuel out the exhaust.

my new dream. i have a exploder just sitting around i wonder

Usually the jeep bodies rust out and your looking for a body to put on a jeep frame...

@BuyFixFlip

Жыл бұрын

Yeah this one was rust free luckily

Maybe you could raise you’re alternater bracket up or shorten just a bit

What did you use for the injection pump and turbo? I have one of these engines and would like to install it in something. Also where did you source the clutch and bellhousing from?

@BuyFixFlip

Жыл бұрын

Clutch is factory willys clutch bellowing is factory willys. The adapter kit came from Greg at overland diesel. The injection pump is stock and thr turbo came from Greg as well

Lower idle is way better. The 1200 rpm isn't an idle and it's noisy

I don't know what kind of motor mounts you used. But if they're solid mounts. You might consider good heavy rubberized motor mounts. That way under the lower idle speeds you might not have as much vibration. Just a thought

@BuyFixFlip

Жыл бұрын

Yeah I'm looking into hollow mounts now!

@Vincent-ly2ik

Жыл бұрын

I was thinking the same also the vibration at idle is normal and the 750rpm is the correct setting personally I would have backed it off another thing too note is that a lot of the factory diesel CJ’s had four hood latches.

Dang. 33 mpg. My Daihatsu Rocky gets 30, bone stock. When the engine goes out I’d like to install a smaller Kubota diesel.

I love the Kubota diesel idea. But a lack of a roll cage scares me.

@BuyFixFlip

Жыл бұрын

They made it through ww2 and the Korean war without them!

@edwardhoward4708

Жыл бұрын

@@BuyFixFlip not all of them!

@hksjoshua

9 ай бұрын

Exactly.

@scrapperstacker8629

9 ай бұрын

@@BuyFixFlip soldiers were considered expendable.

Wo nice and clean swap, luv it. Does the blue Jeep at the end also have the Kubota?

@BuyFixFlip

5 ай бұрын

Thank you, also yes it does. We now have 3 kubota jeeps!

some day this thing will lay on you. Install a rollover bar.

That’s sweet 👌🏻 any good wheeling places up your way? I’m in stark County. We also go to wellsville a good bit if your interested

@BuyFixFlip

Жыл бұрын

Nothing too crazy we go to southington and some in PA. We actually went to Wellsville a week or so ago with them it was a blast.

@willcrosbie8806

Жыл бұрын

I’ve been meaning to try southington

@willcrosbie8806

Жыл бұрын

KZread is the only social media I do believe it or not I’ve never had a Facebook only thing I got is my side business account my woman runs it’s called Lennox auto and fabrication

that depends on the switch on hours, the total hours can be skewed because of this

@BuyFixFlip

Жыл бұрын

I agree, the unit I purchased showed switch hours and engine hours!

@dustygable5006

Жыл бұрын

@@BuyFixFlip most carriers do, well the ones i deal with. though some only show total hours and engine hours. i also deal with thermokings as well

Any chance a bigger balancer would help

Pls install roll bars!

Did you ridge ream the cylinders before you turned up the RPMs?

@BuyFixFlip

Жыл бұрын

Nope, no one that has done the swap that I know of has done it either. It's been a great swap so far!

I'm thinking shakey idle is air in fuel or bad overflow return valve. What transmission did you hook up with adapter?

@BuyFixFlip

Жыл бұрын

T90 factory transmission!

@NoNo-in5tu

Жыл бұрын

@@BuyFixFlip sorry I posted before you mentioned it in video 😅

Do you have a video series of the build? Who builds the adapter kit?

@BuyFixFlip

6 ай бұрын

No I don't, but overland diesel builds the adapter kit. If you need help with the swap email me!

HI , I m new to your channel, and I did subscribe, question is which kabota engine did you use, and where did you get the adater sytem for it , I have a 1964 Cj5 with the v6 buick motor, I have 3.73 gears with the T150, later model 3spd, do you think this would be a good swap for me , my jeep is 75% road driving with a bit of sand beach off roading, I have though about the VW TDI but I m on a tight budget, retired sort of thing ,,,

@BuyFixFlip

Жыл бұрын

I give those answers in the video. Also 3.73s would be great on this motor. I have 5.38s