KTM Lower Heim Joint Shock Bearing Replacement & Check for "Slop"
Автокөліктер мен көлік құралдары
Have you noticed some "slop" in the rear end? Chances are the heim joint needs replacing. I also show you how to check for "slop" as well.
/ nicolaspoirier.enduro
Please note: I greased my bearing with Moly B. The manual on pg 42 says not to because the OEM bearing has a Teflon coating and the grease will disturb that coating. I haven't a clue whether aftermarket bearing kits like I used (Moose Racing) are coated with the same coating. The decision to grease/not grease will be up to you and your product you selected as a replacement.
My bike: KTM 250xcf 2009 w/ PDS rear shock
Upper shock bearing replacement | • Video In part 2 I cover removing and replacing the upper shock bearing. While similar to this, there are some differences.
I dunno by grapes (c) copyright 2008 Licensed under a Creative Commons Attribution (3.0) license. dig.ccmixter.org/files/grapes/... Ft: J Lang, Morusque
Пікірлер: 50
Finally someone who posts a video replacing a bearing that's actually worn and doesn't come out easily. Also like how you use everyday tools instead of all kinds of specials that nobody actually ownes or wants to buy.
@NicolasPoirier
5 жыл бұрын
Thanks! Best of luck swapping yours out
@mt1885
4 жыл бұрын
That is why race bikes are generally destroyed by people using a mini-sledge and flashlight working on them. 🚯
I'm going to mark my socket at the depth it's in before i knock out the bearing... Good vid man
@NicolasPoirier
3 жыл бұрын
Clever!
Weel done video for the average bloke with shed tools 🤙
Spend the $15 on a seal puller. One of the best tool buys I've made. I felt like an idiot for not having one for so long. Also get a deadblow hammer.
Good video. Good technique for “garage” repair. Much better than most... Thanks for posting!
Spot on mate my bearing was a nightmare had a hole in so stuck this vid helped alot cheers
Nice . Did mine pretty much same way , Wrapped brake line loosely with aluminum foil to protect from heat and sprayed a little PB Blaster on both sides before whacking to help lube it . Heat is good.
Thanks ! Helped a lot seeing it done with regular tools
Really helpful video! Especially liked the fact you were using normal tools Cheers!
Thanks for posting! Very useful!
Nice job! Very good video
Nice job bro! Thank you!
Great video.. helped me out a ton. Just a note: Be careful if you have impact sockets. I had to drop to a 21mm for it to clear and pass through.
Great video! Love the commentary 😂
This was helpful, thank you!
Thank you !
I find it easier to do with the swing arm off, you can also service the swing arm bearings at the same time 😉
Great m8 thanks a lot
Just about to do my lower bearing next weekend, thanks for the vid man, really helped. Me understand the process, is the heating up necessary as I don't have a blow torch, would it take some doing to remove it cold.
@NicolasPoirier
4 жыл бұрын
Heating up the parent metal around the bearing isn't necessarily needed. You can most certainly do it without the use of heat.
Thanks a lot sir!!
@NicolasPoirier
4 жыл бұрын
Glad I could help
Disculpa soy de mexico donde puedo conseguir ese buje o cojinete?
Tanks men
@NicolasPoirier
6 жыл бұрын
ENDURO ASTUR no worries. Thanks for watching!
After removing a very tight lower bearing the new one is not a tight fit in the hole. Would a decent bearing locking compound work to hold the bearing?
@NicolasPoirier
4 жыл бұрын
This is pretty interesting. You would think that the bearing that you're replacing it with has the same outer diameter as the one that you pulled from the bike. As for your question I think you're right. I have had luck in the past using the green retaining compound made by Loctite because I had some sloppy wheel bearings. It seemed to work great. Hopefully something like that would work in this case to.
👍🏻
What could i do if the helm spacers won't come out? They're rusted on I believe and no matter how much I pound on them with a screwdriver they won't budge
@NicolasPoirier
4 жыл бұрын
PB blaster or equivalent and add heat to the equation
Hi, I have similar spherical bearings with heim joints in the rear lower shock of my car. I'm noticing high pitch metal noise in the suspension during bumps. Do you think it's the heim joints just not being lubed? Have you noticed any metal noises using the grease instead of Teflon?
@NicolasPoirier
5 жыл бұрын
I really don't have a good answer for you. That's a tough one especially on a vehicle. It's not like you can just hang your head out the window and listen to see what's happening. My apologies, I really don't have much for you. Also, I greased mine but I don't think I put too many hours on the bike after I did that and I sold it. So I don't remember whether or not it made any noise.
@bobs9242
5 жыл бұрын
@@NicolasPoirier ok thanks
So i managed to get almost everything in on mine after alot of force :I but the spacers wont go in, i got on in by using a socket but the chain side wouldnt go in so carefully removed both and now i dont know how to get them in..
@NicolasPoirier
4 жыл бұрын
Hmmm, you shouldn't need a socket to insert the spacers
@cappe_yt9182
4 жыл бұрын
Nicolas Poirier yhee thats so weird.. i put them in the freezer for a hour or 2 and nope, gonna let them freeze over might and take a look tomorrow :/
How long it was working after this change? I am curious if allballs + grease lasts longer than original KTM
@NicolasPoirier
2 жыл бұрын
I sold the bike shortly after doing this maintenance to a riding buddy. Therefore, sadly I don't have a great answer for you. He rode it more than I did and I THINK he didn't have to touch this bearing for a while.
@midlan6
2 жыл бұрын
@@NicolasPoirier thanks for your reply. I will see 🙂 I used allballs and greased it as you
Any tips on the last step? The install will not fit with the extra space
@NicolasPoirier
Жыл бұрын
Sorry, not sure what you're asking about? Are you referring to the seals? ...or the spacers being installed after the seals are in?
@icekluntt
Жыл бұрын
@@NicolasPoirier after the complete install, where you say in the video that you can mount the shock and there is some air pushed out, does not work with me. There is still to much space so the shock will not fit over it...
@NicolasPoirier
Жыл бұрын
@jt-id7rk From what i gather you're referring to the spacers with grease on them not seating all the way because the grease traps air. I would suggest having a buddy hold the spacers tight to the heim joint/aluminum swingarm while you guide the shock clevis over the spacers. Best of luck
@icekluntt
Жыл бұрын
@@NicolasPoirier thanks for the reply!
Since the Heim Joint is a pain in the ass, I have it replaced by plastic (polypropylene) cylinder five years ago, and there are no traces of use on it. It should be tight in housing and the hole must suit the bolt. That is all. No need for any grease, I don't care for water mud or any chemicals and it costs around 4 bucks.
@NicolasPoirier
3 жыл бұрын
That's a pretty creative solution
Good enough for government work lol they would have used a ruler .