King Pin Replacement Isuzu NPR-HD (GMC Truck W4500)
Тәжірибелік нұсқаулар және стиль
KingPin Replacement on Isuzu NPR-HD NPR NQR NRR or GMC Chevrolet W3500 W4500 W5500. Removal and installation using 20 ton bottle jack and hydraulic press.
I used King Pin Kit number 5-87832-220-4 (5878322204)
Замена шкворня цапфы на Исузу. Извлечение и установка DIY
Пікірлер: 106
We welded a jig that bolts to the spindle and has a pipe that's centered over the kingpin and we drive it out with a sledgehammer. Works great for this job.
Very informative, made a jig like yours to do our truck and worked like a champ, thank you.
Amazing how easy the new pin went in. Considering the bushing material; odd the old on was sized up like it was. Dusty dry though.
Best video I've seen on KZread in a long time. King Pins are never fun. You make it look easy!
Ты красавчик, береги себя. Хорошей и денежной работы тебе. Не стесняйся своего английского и смело комментируй что ты делаешь.
Excellent video.... Shame I only found it AFTER I had done one. Thank you
You are a Master Mechanic. Great job.
It's amazing how smart some people are on here . You'll spend a couple hundred dollars on pins and bushings and not twenty dollars for grease and a bottle jack .
thank you for great detail video on show the job
Very good job ! Very good video !!! Thanks!
Great video, now I understand why the repair shops charge what they charge.
GREAT VIDEO THANKS
Many people ignore!!! That why grease nipples are given to lubricate such moving parts like: king pins, tie rod ends, leaf springs, propeller shaft center bush & shaft cross. It's better to greasing all given grease nipples after every 5000Km.
great video, thank you very much, I will take my truck to the mechanic, there is not way I can do that!!
Nice work! A+
This guy does take a lot of risks.and that kingpin did not know grease on its lifetime😋
Nice man I wish you be in the area so can give you the job you are doing a great job!
Thank you 😍😍😍😍😍😍😍😍😍
Awesome, I couldn't imagine how you were going to break 2 20-ton bottle jacks. I was imagining jacking up the truck; but how do you break a 20-ton jack doing that? And I was impressed with that jig you made to remove the king pin. Also, whoever edited this has mad skills!
Wow great job
Wow... Awesome task.
Nice job
Good job. 👍
Great work buddy 👍👍👍very good 👍
thank you
!!!👍👍👍👏👏👏GOOD JOB
Thank you👍👍👍❤🧡🧡
баярлалаа хөгшөөн/thank you
Awesome!
Use channel instead of angle iron, weld the horizontal top and bottom pieces inside the vertical pieces so they will be stronger. We had a kingpin pressed out of a 1978 Ford F250 pickup. We had to remove the I-beam out of the truck and take it to a shop where they pressed it out. How much pressure? 27 tons.
Bravo.
I want to ask a question because the piece has play if it is very difficult to remove it
Did you preload the thrust bearing to check if you needed a top shim ?
I am hoping someone can tell me the torque specs on the 12 T55 torx bolts that fasten the rotor to the hub. Thanks in advance.
I have a 50 ton jack ima have to make one now lol
naic jop thanks
Don’t use a wrench on a square head. You will strip it. Use either an actual square socket or a 12-point socket. On a second thought, you can use a wrench, but the other way around where it has a 12-point. The problem, though, will be lack of leverage. I’d definitely go with a socket and a breaker bar. They do sell ratchet breaker bars for a quicker job. I’ve seen some people use an impact wrench on that tool, but I don’t know if the manual says it’s okay or not. Some also say you should lubricate the threads to make the tool last longer.
Very informative and much appreciated!! PITA though.. not looking forward to it.
@ 14:40 Thou shalt not heat up the cast iron I-beam or steering knuckle! You also fail to measure your axle (I-beam) bore for out of round ! If it's out of round, then you need to bore it out and sleeve it back to size or your king pins will have short life.
@hawkboy000
3 ай бұрын
This! A buddy of mine was telling me that today
а регулировочные шайбы между серьгой балки и цапфы,и уплотнительные манжеты с внутренних серёг цапфы,чтобы во втулки грязь не попадала,что не надо ставить?
King pins are a king size pain in the ass.
great video ! i have a question though. is the work the same for different wheel, w/o brake disc, but a drum?
@NasirHussain-wt2si
4 жыл бұрын
Yes. King pins are same in both disc & drum types vehicles.
Nice work! You just outlasted it.
Do the king pin always have to be pushed upwards to remove ? Or can they be taken out either way ?
@smallchunkaground2071
Жыл бұрын
You can drive them down through also.
Good work. Thanks
Is it a necessity to remove the disk and hub out or its possible to work around it?
@thetrick4fun
5 жыл бұрын
Oh yes. Without removing a hub you will not be able to remove the shield around and you won't be able to work. And it is one of the easiest part to remove the hub.
@yasserchouhaita
5 жыл бұрын
@@thetrick4fun thanks for the tips
No torch on kingpins ever!
@bandit6918
3 жыл бұрын
Why not ?
@mongomay1
3 жыл бұрын
@@bandit6918 Heat treated parts under high stress on front end gets ruined by torch heating.
Bien pero la “percha” es muy frágil tendría q ser dos ejes gruesos con rosca en ambas puntas las planchas de por lo menos 25 mm de espesor lo demás está bien 👍
Well done , can you do mine now ?
Haz pasado más trabajo bregando con la soldadura y el pasador que sacar el king pin
@CanBus-li5ky
9 ай бұрын
Te voy a grabar cuando saques uno aver si son tortillas de arina
👍
something is wrong with the playback on this specific vid. buffering out like craxy. other stuff play ok
Tiger tool says we can help get that out for about 1700.00..... He be like where's my scrap pile and welder.😆
If someone follows this guys instructions he could get them hurt this is the kind of you tuber you don't need been there done that buy the right tools this guys a mechanic come on
Thank you 🇮🇳⭐⭐⭐⭐⭐👍
I think better if he spray DW40 first before jack
How cute r u😂
Can anyone give an opinion of how many hours labour to replace 2 kingpins like on the video?
@carlintorneiro
4 жыл бұрын
kzread.info/dash/bejne/a3mVw5R_ldSXm6w.html
@raduberaru9369
3 жыл бұрын
Depends! The make of the truck ( MAN, DAF , Volvo , Scania) or if it is a truck or a trailer steering axle etc. ... most of them are well known and they have a different type of difficulty grade. But they are already timed. In Europe it is calculated between 3 to 6 hours per kingpin on a head unit and for trailers can go up to 10 hours per kingpin
I forget grease the lower part. Now the wheel shake which king pin loose.
Well that saved you $2500
What size nut on the hub?
@juliocer9604
4 жыл бұрын
Also what size bushing extractor?
@jamesbyrne9699
4 жыл бұрын
41mm
@adamneusbaum3749
8 ай бұрын
@@jamesbyrne9699Excellent, same as lugnuts
@jamesbyrne9699
8 ай бұрын
If you need to know anything else, just ask. I work on Isuzu for a living
Hello, Can anyone help me with the king pin overall intervention mechanical design. I am currently doing my mechanical engineering course as a final year. Any concrete kind of information would really be appreciated !!💯 New design, new ideas(hydraulic, pneumatic or any transmission system), king pin inclination angle.
How long does it take?
@thetrick4fun
5 жыл бұрын
One day for one pin
@tyler19966
4 жыл бұрын
Great job .I am going to make me one of that tool
Men playing with tools ,Never say easy
Must be Russians that’s how we do it as long as gets job done ☑️
Hello how much Pounds to move the rotor?
@thetrick4fun
5 жыл бұрын
Hub bearing preload 3.7-7.1 Lb (1.7-3.2 kg) if you put new hub bearings 3.1-6.4 Lb (1.4-2.9 kg) if you put used hub bearings
Hello sir good evening how are you fine sir I need you job mechanical
I am heavy vehicle mechanic let job
wow, what a pain in the ass
@thetrick4fun
5 жыл бұрын
That's right! Very hard work
@jeffs53
5 жыл бұрын
needing to do this on two of my trucks... =(
New York mechanics would never do what you did. They simply replace the whole thing not fix it
Poor guy please some body tell him how do that before him kill him self
@RobinatorsPlace
8 ай бұрын
better idea- you follow his lead.
Muy lento
@CanBus-li5ky
9 ай бұрын
De donde eres ? Supermán para ir a verte hacer uno aver si son tortillas de arina
Scheiss Werbung.
There was so much hack in this I think I caught the covid
Muy lento
@edwardhernandez2784
4 жыл бұрын
Tiene una manera más rápida para hacerla envía un video por favor