Killing Welding Method! ! Sanitary piping (Senitari)
Тәжірибелік нұсқаулар және стиль
Good morning. welder jin.
The theme of this video is welding and welding of Sunnytari pipes.
Have fun and subscribe.
It is a motivation to make a new video.
First of all, the tungsten rod should be sharp.
The arc is concentrated in one place so that Tech welding works well.
Ceramic nozzle is not important for Tech welding.
The voltage is 80 amps, so the heat is not transmitted to the opposite side when Tech welding.
Set with one touch.
Place the center of the short pipe gap.
Tungsten rods should be pulled out short.
As the tungsten angle approaches 0 °, the arc concentrates in one place.
The alignment will fit well.
It's the fundamentals of every pipe piteop.
Not right.
Clean up the cross section with diamond Yasuri
This time, let's correctly.
After all, it's better to stand up. (Gravity)
Let's observe
Note that if you do Tech welding at 6 o'clock, the next Tech welding position will be at 12 o'clock on the other side.
Do tech welding with zigzag because the pipe gap should not open.
It's like this.
Ceramic No. 6 Diameter (15mm)
Tungsten rod (2.4 pie)
Tungsten Rod Extrusion Length (5mm)
4 "We start welding Sunnytari.
Welding voltage was set to 80-90.
You should arc start and watch the molten pool.
Do not start weaving right away, but wait for the melt to melt and the backside beads to form.
Why not start at the first start point?
Did you solve the question?
We make a cabinet with regular weaving.
It was edited at twice the speed to get rid of boredom.
Please understand and watch.
Sunnytari welding is characterized by welding without solvent
It is a killer welding.
Because we do not give a root gap but
The molten water that makes the molten pool may have convex beads or concave beads under the pressure of purging.
The purge pressure welding process is very important.
If the purging pressure is strong, push it out
If the purging pressure is weak, it will be affected by gravity and sink at 12 o'clock and convex at 6 o'clock.
The reason for narrowing the width of the widget is butt welding without improvement, and there is no reason to widen it.
This is to increase the thermal conductivity.
It is a method of welding while maintaining the liquefied water delivered to the backside beads.
Since writing a lot of wrist Welding
It is desirable to perform welding with the least amount of force.
Also, there is a pipe gap during welding
It is very difficult to find a weld seam.
You will have to move your head often so that you don't miss the weld line and concentrate.
It is recommended to start 20mm behind when welding the other side.
Because it's a preheating concept, to make a natural connection with the backside beads that we created.
Look at the paper tape side.
The red light seemed naneunge.
It feels like a backside bead is created.
Let's observe
Thank you for watching.
Challenge with new welding video.
Subscribe.Like.Share
subscribe!!!
"welder jin"
/ @welderjin
Beugeum sources .....................................
HYP - Catch Me If You Can
Music by (HYP MUSIC)
• [BGM] 저작권 없는 신나는 피아노 음...
HYP - Eyes (eye)
Music by (HYP MUSIC)
• 무료 BGM 감성적인노래 HYP - E...
HYP-Monologue
Music by (HYP MUSIC)
• [BGM] 감성 저작권 없는 음악 | 비...
#Welding #Tig Welding #Sunnytari
Пікірлер: 865
통역!!! 번역의 문제가 심각해요. 6시 테크웰딩 후에 반대편 테크웰딩을 하라는 말인데 번역의 문제. 죄송해요.
@user-cm2ul6eo4b
4 жыл бұрын
써니타리 위생배관 1미리 해봤는데요 테크치기가 너무힘드네요. 너무얇아. 반전기에도녹는게 보이는데. 원터치 가능할까요.
@welderjin
4 жыл бұрын
1.65t일까예요. 나중에 테크치는 노하우 공개해볼게요.
@asepgunawan7619
3 жыл бұрын
ooo9oo9o
@ludbercitoludbercito7494
3 жыл бұрын
🤣🤣🤣🤣🤣
@user-jn5pu3qv6y
2 жыл бұрын
А толщина стенки трубы сколько мм?
눈부시지말라고 매너손 너무 감동👍👍👍👏👏👏👏
다른 채널들보다 설명이나 비디오가 구체적이어서 너무 좋습니다^^ 많은 도움이 되네요~
기가 막힙니다. 신의 경지 입니다.
@welderjin
4 жыл бұрын
헐 그정도까지는 아니구요. 감사합니다.
자세한 설명과 선명한 영상으로 이해가 쉬웠습니다. 감사합니다! '좋아요', '구독'
@welderjin
4 жыл бұрын
감사합니다 새로운영상으로 다가갈게요.😊
대단하시네요... 시작위치가 자세가 엄청불편할텐대 이걸 논스톱으로 거의 끝부분까지 작업하시네요
촬영 굳 용접기술 굳 화질 궅 촬영 다각도 굳 요즘 영상 올리는 분들 정성과 노력이 느껴 지네요 특수용덥 기능 자격증 받고 수년 동안 한번도 안해보니 뻥이지만 구경만 해도 재미 있네요 수고 많았습니다
@welderjin
4 жыл бұрын
워 너무 좋은 평을 주시네요. 더욱 분발할게요. 감사합니다😁
우와 이렇게도 되는군요 감사합니다 처음 알았네요
선생님 좋은교육감사합니다
@welderjin
4 жыл бұрын
댓글 감사합니다😊
상세한 노하우 영상으로 공급해 주셔서 감사니다...
잘~찍었어요..구욷 영상 ~이네요
Dziękuję za napisy w języku polskim. Bardzo przyjemnie ogląda się twoje filmy.
@welderjin
4 жыл бұрын
Dziękuję za obejrzenie. Rzucę ci wyzwanie nowszym filmem.
제살용접은 말그대로 모제사이의 간격이 제로였을때 가능한거져 전압은 알맞게 알곤용접은 위빙과 전압을 잘맞춰야 용접이 잘됩니다 영상 잘봤습니다 저도 알곤용접사고 현재 알곤용접병행 일당직종사잡니다 늘 용접법 잘봅니다 경력이 있다하여 자만하지않고 배우고 또배우고 나보다 더나은 용접법이 있다면 이렇게도 저렇게도 열심히합니다 구독자분들도 영상만 보지마시고 실전에 하실때 유용하게 자기습성에 맞쳐 하시다보면 실력향상에 도움 많이됩니다 용접기술자들 화이팅~~~^^
That is a work of art. Outstanding skill ... Well done!
멋집니다....좋은 정보 기술.감사 합니다.
@hieuvu4487
4 жыл бұрын
Dẹp
i am just starting to learn! Now , this is what a professional welder welds like!
멋지다..ㅜ 저도 빨리 진님처럼 a급용접사되고싶습니다
Watched from Kansas USA. Great work. Great video. Thanks!
@welderjin
4 жыл бұрын
Kansas USA. Thank you
용접하는게 아니라 예술가시네요
Gracias por el vídeo. Muy buena soldadura. Mañana intentaré hacer lo mismo a ver si me sale jejeje.. Todavía necesito experiencia. Me ha gustado mucho ver como hacía la soldadura esa persona.. A ver si en unos meses consigo hacerlo parecido :D ^^
역시 최고네요
@welderjin
4 жыл бұрын
과찬이세요. 감사합니다. 소중한댓글😘
I love watching precisious asian welders at work!
@eduardosampoia5480
4 жыл бұрын
That's fucking racist.
안녕하세요^^ 저ㄴ 용접학원만 다니면서 용접을 배웠던 사람이고 실제 필기시험(용접/특수용접기능사)는 합격했는데 실기에서 둘 다 떨어져서요 다시 도전해 보려고 합니다 잘 보고 갑니다 더 좋은 영상 기대할게요^^ 감사합니다^^
@welderjin
4 жыл бұрын
화이팅😊 자격증과 실전은 크게 많이 달라요. 용접직종을 택했다면 하루빨리 취업하시길 바랄게요.
기술이 좋으십니다 ^^ 엄청난 내공이군요
우와 대박 멋지십니다 .. 존경합니다 ㅎㅎㅎㅎ
훌륭하십니다~
@welderjin
4 жыл бұрын
과찬입니다.😁
Magnifque soudure, les gros plan intérieur sont formidable ! Félicitations
Nicely done. I really liked the camera inside the pipe showing the welding from the inside!
Nice my friend. Good job!! Take care always!❤️
Sim mestre sou do Brasil aprendi que uma vez que surgiu uma possa de fusão devo prosseguir com essa gota de mel giratória visualizando assim a emenda do tubo caminhando em frente mantendo o grau dá tocha protegendo meu cordão de solda em todo meu percurso obrigado você é muito bom lindo trabalho bela apresentação e filmagem 🙏
실력이 대단하시네요!
Great camera work. I'm just starting out with my everlast tig welder so everything is pretty new but I would like to start a career in welding.
@jdtracing6502
4 жыл бұрын
What kind of Everlast do you have? I have the 210 EXT which I am very happy with. Everlast makes an affordable machine that is super reliable and easy to use. The only thing I would recommend doing is upgrading to a CK torch with a flexible head and maybe some larger cups from Furick or GLS Fab. They are not expensive and make a world of difference. Also If you are welding stainless, backpurging is a must. I have figured out how to make a really nice back purging setup for a very cheap price. Send me a private message if you want the details as I don't want everyone knowing my secret!
좋은 영상 감사합니다 ㅎㅎ 😂 💕
이게 제살 용접이라니 ;;; 대단하십니다...
@welderjin
4 жыл бұрын
다 할수 있어요. 대단까지는.......댓글 감사해요😊
아름다운 용접ㅎ
The camera shot you took from the inside was awesome🤙🏽
@welderjin
4 жыл бұрын
Have a nice day.
@yianiskourebetsis8637
4 жыл бұрын
@@welderjin olympiens knwes
Olways the best my ticher. Good luck
@welderjin
4 жыл бұрын
Thank you. Good luck will come to you.
잘보고 갑니다^^
Saya dari indonesia saya sangat senang dengan trik welding yang di berikan, saya seorang welder yang masih butuh belajar, bravo master
최고다! 짤짤이 손이 안보이네ㅎㅎ
Love the video you are very talented man keep more videos to come thanks
Very high attention to detail! Excellent job!
@welderjin
4 жыл бұрын
Have a nice day.
You have a great skill, good work!
Great job thanks for sharing and teaching !
배우고싶네요 깔끔하게 잘나오군요 최고입니다
Ap ka continues bohat acha hota ha mujy bohat kuch sekhne ko mela ha
Ficou Incrível muito bom 👍👍👍👏👏👏👏👏
이거 보니까 알겠네요. 한국사람들은 정말 용접을 잘합니다. 이론적인 매뉴얼이나 이런거 없어도 도제식으로 내려온 노하우의 레벨이 틀려요.. 진짜루..
I just started professionnally learning welding (stick, mag/mig, tig) . This is impressive !
좋은 영상 감사합니다! ^^
좋은 영상 잘보고 갑니다
@welderjin
4 жыл бұрын
감사합니다. 좋은하루 되세요😃
@thelk1851
4 жыл бұрын
👍👍👍🖐️🖐️🖐️🖐️
Great job! Amazing skills there brother.
@welderjin
4 жыл бұрын
Спасибо, брат.
@johnwilletts337
3 жыл бұрын
A joint that tight shouldn't need to weave it
@johnwilletts337
3 жыл бұрын
Also weld not clean on outside so angle or gas flow is wrong there should be flush weld inside as penetrative causes turbulence
Super vidéo. Pour ma part la porcelaine glisse sans arrêt. Pas évident
Great job jin. . Thanks For tips. . . Saluttttttttttt from WELDER 🇮🇩🔥🇮🇩❤️
Nice work Jin. By the way, what make or brand name and model number of your tig welding machine. Thank you very much, Barry
Nice to hear from you thanks
Nice welding job. Pipe welding with urgon purging.
Increíble eso sí es un soldadura muchas gracias por tu vídeo
Nice Jin, Thank you for the video! Much welders cannot do that...
@welderjin
4 жыл бұрын
Thank you. Many welders can.
@jaimemendez8099
4 жыл бұрын
I can do that 👍!.
''''Diviértete y suscríbete...'''' -- dice... welder jin. No tienes idea lo mucho que me he divertido... hasta tuve un ataque de carcajadas... Mi familia se vió forzada a darme un sedante...
@welderjin
4 жыл бұрын
Tanto poder me dices. Me siento muy bien Volveré con un nuevo video.
A agulha Um pouco Mais recuada A solda Fica com Mais Brilho. . . Mas Parabéns ferramenta Afiada 👍
Sorry for late comment,would you explain why haven't you used a filler rode?
새싹이 많이 배워갑니다
@welderjin
4 жыл бұрын
감사합니다. 좋은하루되세요.😊
Very skilled welder, well done.
Джин,ты молодец очень хорошо вариш есть чему поучится у тебя.Удачи в работе!!!
@welderjin
4 жыл бұрын
Спасибо за просмотр
Good welder I try to study about it
Браво мастер!! спасибо поучительно очень и все подробно расписал молоде!!! за камеру внутри чтобы видеть шов отдельное спасибо !!!!!
@welderjin
4 жыл бұрын
Вам любопытно, швы? Я вернусь с другим видео в будущем.
@diletantshow6406
4 жыл бұрын
@@welderjin yes. ok!!!!
Looks good mate!!👨🏭
@welderjin
4 жыл бұрын
Have a nice day.
Are you doing this weld without adding filler metal?
マスター you know what you are doing... I am your new subscriber
@welderjin
4 жыл бұрын
Thank you for signing up. I'll reward you with a good video.
Can you please explain to me that tack welding method? I’m shocked on how easily you tacked it, I have nailed everything else down where I don’t get color inside the welds, penetration is perfect, and no birds eye. But my freaking tacks sometimes go through and sugar.
Thanks for the video.🤑 ✌🇺🇸✌🤙
Japanese welder is known as among the best welders with the most professional welding technics in the world
@miseryer
2 жыл бұрын
ㅂㅅ 한국이겠지 어딜 듣보잡 일본을
Your film is very helpful but i want you to show me everything in real practice 😎
@welderjin
4 жыл бұрын
Thank you. I'm in the process of showing you everything.
Parabéns ficou muito bom!!
¿Cuál es la manera para calcular la presión de purga? Saludos desde México
Love the masking tape purge dam old school, what do you use to clean the outside of the weld brush or paste?
@welderjin
4 жыл бұрын
Clean the outside by putting sus wire blush and cup blush on a power drill.
@jaimemendez8099
4 жыл бұрын
I use a stainless steel brush and stay nice and clean. You berly see the weld. 👍👍
@eduardosampoia5480
4 жыл бұрын
Cup blush to crean the wehood. It wook wery goot.
👏👏👏👏👏👏gracias por compartir Un maestro.👍💪💪
@welderjin
4 жыл бұрын
Gracias Que tengas un buen día.
Is it common to walk the cup on 16 gauge tubing like in this video in other parts of the world? Sure the weld looks nice but i wonder how much shrinkage there was in the overall length of the pipe. I've purge welded miles of pipe in my life but never did it this way....I do possibly see a benefit on thicker gauge stuff though like 1/8 inch wall and such....Maybe I'll give this technique a try and see how it goes. A guy can never have enough welding knowledge or techniques in his bag of tricks...
gracias por el tiempo y video, ahora podrás hacer un vídeo con soldadura en aluminio con arco pulsado?? gracias
Waw...cara pengelasan nya sangat bagus 👍👍👍🤝 indonesia 🇮🇩
Bravo, leçon de Maître
까페에서 반칙하신거 응징하러 왔습니다ㅋ 근데 뭐 깔만한게 없네요ㅎㅎ 잘 봤습니다^^
@welderjin
4 жыл бұрын
ㅜ.ㅜ 감사합니다.
Good Instruction Thank you
Mantap,,weldingnya halus& rapi
@rusdiyanto5006
4 жыл бұрын
Petrus Channel ,ngomong sama siapa lay..
Nice cup walk.
Root looks awesome.
@welderjin
4 жыл бұрын
Have a nice day.
Trabalho lindo de se ver, nota 10 !!!
Mantulll,sy dulu jg welder gtaw,klu liat org lg ngelas naluri sy lsg keluarrrr biasa..
Thats great ...... Iran has a lot of welders like this .
@welderjin
4 жыл бұрын
Thank you. Have a nice day.
Muito bom seus vídeos parabéns deus abençoe
안녕하세요 구독 좋아요 꾹꾹 누르고 시청하고 있습니다 저는사실 만드는걸 좋아해서 용접과 특수용접을 배웠는데 박판 용접을 배우려고 했는데 어쩌다 용접기능사 특수용접 기능사 자격증도 취득을 했지만 기술은 박판용접 인것 같습니다 퍼지를 해서 용접후 빠우 까지도 하는영상 보여 주셨으면 좋겠습니다 스텐파이프 몇티를 사용 하시며 전류는 얼마로 하는지요 알려주시면 감사하겠습니다 좋은영상 감사드립니다 선생님 채널도 번창하세요
우와...진님 조회수 실화입니까? 대박^^
@welderjin
4 жыл бұрын
그러게요... 왜 조회수가 많을까요?
Amazing Jin!
Hola Cuantos kilos de gas purga lo as puesto ??? Gracias y saludos
The best gan. 👍
No sé cómo vamos hacer al final,tenemos que ponernos en contacto me mola mucho tu pantalla de soldar,estoy comprando mucho en China no creo que es muy difícil comprarte una pantalla gracias
6호는 거의 10mm 정도인데요.. 자막은 15mm로 나오네요. 보통 내경을 얘기하죠. 외경이 아닌.
Best I've ever seen!
굿
@welderjin
4 жыл бұрын
😊