Good video. But shouldn't you do routing on the back plane when you are using THT components. You are placing components on both sides and this requires vias. Your way could lead beginners the wrong way.

@mathcodeprint

3 жыл бұрын

I pinned your comment to the top. Thanks for pointing this out. I am a beginner, trying to find my way and giving a beginners perspective to others. Thanks for checking in on us noobs :)

@honzapom

2 жыл бұрын

That's actually wrong. THT components (unlike SMD components) get electrically connected to both sides of the PCB so you can do the routing on either. The way it's done in the video is perfectly OK.

@mathcodeprint

2 жыл бұрын

Thanks Honza !! 😁😁😁

This is what I needed. Simple and basic. And most of us who are searching for this are not advanced. From these fundamentals we can build on them. Thanks for the simple and easy to understand tutorial

Thank You! I cannot believe how hard it was to find a good Kicad tutorial from a native English speaking youtuber. This is exactly what I needed.

@mathcodeprint

3 жыл бұрын

Thanks, I am trying to pick more subjects as well.

The best!! You are a natural teacher. You covered the basics, didn't get bogged down in the small details , and you showed the basices for getting a board designed. Thank you for the absolute best intro video out there.

Thank you so much for this presentation. It is very well laid out for the beginner and was easy to relate to version 6.0. I especially appreciate that the video is an all-in-one and not drawn out over multiple sessions. Thanks again, liked and subscribed.

Great Kicad tutorial! I like the way you cover short cut keys and general workflow using a simple example. Very noob friendly!

I LOVED IT TOO MUCH this is the only tutorial that I wished was longer

Thanks for making this tutorial. I've been looking at a proper introduction to KiCad and PCB design for ages and most of the stuff out there isn't this comprehensive or explained in simple English! You just helped me restart a breadboarded project that has been collecting dust for over a year because I couldn't find a proper tutorial.

Best tutorial I've seen yet. You took your time to teaching as opposed to others. Thanks so much.

I've hunted around for a good tutorial... this is the best beginner tutorial for kicad I've found. thank you !!!

A very helpful video! From knowing nothing about KiCad to being able to design a PCB for my pet project in 20 minutes! Thanks a lot!

Finally a REAL KiCad tutorial ... THANK YOU! Looking forward to seeing more from you!

@mathcodeprint

3 жыл бұрын

Wow. Thanks ☺️🤩

Thank you for the video. I have watched many kicad videos and their examples always are too complicated for a tutorial. A nice simple layout with just the basics is what I needed.

Excellent introduction to KiCAD with many insightful tips. Thank you.

This was really helpfull, I'm commenting so more people see this video. In college now and this helped me a lot since I want some more practical knowledge and skills. Thanks for making this

Perfect tutorial for beginners. Loved the way you taught multiple ways to assign footprints. Thank you so much!

@mathcodeprint

3 жыл бұрын

Your welcome. It was so confusing to me at first so I figured ...

Fantastic explanation, thanks so much. Kicad is rather intimidating, and you've helped me understand the workflow a lot better.

Thanks for taking the time to make this vid. Much appreciated :-)

Great tutorial, exactly what I needed to finally get started on some PCBs!

This is a great way to start with a simple LED circuit. This reminds me of the first circuit assembly I made. Thanks man!

you have a very nice and clear voice, thank you for being my introduction to pcb design! :D

Excellent video , I learn more every time I watch.

Thanks for that video which made my effort for another board easier. My first time using cad as I need it to repair an amp I have. Handy for work too.

Woa this is just the tutorial i needed/wanted ^^.

this is much better than proteus. thanks for such a great video.

Thank you, just what I was looking for to get started!

I am experienced with Kicad , but I watched anyway and this is a valuable tutorial...cheers.

@mathcodeprint

3 жыл бұрын

Thankyou so much :)

Just finished this tutorial. You're a G.

Thank you for this tutorial! I couldn't understand the basic schematic -> pcb workflow but this makes perfect sense!

Thank you for good and simple tutorial!

many thanks! very good entry method

Thanks a lot sir. Greatly benefitted from the video😊

Thanks for the Tut. Very informative, I learned something even from the mistakes I made as I following along. I messed up some tracks and wanted to *rip tracks up.* Eventually I found it was to *highlight the track and hit the Backspace key.* Also in the Schematic Assign Footprint stage one can select/highlight the assigned one and copy it with a right click, select copy and then select paste into the next component, instead of going to look for it in the library again. Also one can select and delete a wrong assignment too.

Thank you very much! very useful , step by step

Thank you very much...youi took me from zero to hero in 22 minutes

Super helpful to connect all the pieces of this software for a beginner. It looks like a lot of the icons in the software have been updated since you recorded this, but it still has great value.

Excellent tutorial. Appreciate it

Thank you for lifting the curtain on Kicad for me great video going to follow it in Kicad tonight

Thanks for the introduction :)

Great tutorial. Thank you so much!! I will try to do a video for Kicad V6, because there are different changes.

Amazing video. Thank you.

This would be great for anyone getting into electronics at high school. I remember when I did a Technology class we made a bi-stable LED flasher circuit and had the PCB’s produced. I didn’t understand how it worked at the time but it was so cool to make something and all it needed was a 9V battery - all analogue!

@mathcodeprint

3 жыл бұрын

I started this video with that circuit. I changed as I wanted an even simpler circuit and liked the idea of bringing in addition. Maybe next video should be flasher :)

Thanks for this informative video. For a while, I've been wanting to design a mini-amplifier using a LM386 and wasn't sure what design software would make it easier for a novice like myself.

This is a helpful tutorial for a beginner. You are using multiple screen. That's why you cant dock the KiCAD window at left side as I think.

Good tutorial. Thank you. : )

Excellent. Thanks

Thank you for this great video. I'll be using it as a reference to make a custom Raspberry Pi Hat for my project.

Thanks!

Great tutorial! Does anyone know a good tutorial how to virtually test a circuit board in KiCad?

Creative video, thanks :)

Thank you!

Good video, thank you...

I don't know if you are going to see this or maybe at this point you already know but I can give you advice not to use right-angle PCB traces as you did on routing D1 to R1. Corners cause reflections and can impact the signal quality. In this examples you do not have signals that transport data but if you do design a board where you send bits on traces you should keep that in mind. Great video btw :D

@mathcodeprint

2 жыл бұрын

Good info! Thanks. Had an idea that corners where bad, i did not know about signal reflection.

You gotta make more KiCAD project videos!

@mathcodeprint

3 жыл бұрын

I hope to, trying to discern my way forward. :)

You could also add a copper plane that connects to e.g. ground. This way you can omit routing all common ground wires, they would just connect to the ground plane directly. Makes it easier to route other things with less non overlapping wires etc.

@mathcodeprint

3 жыл бұрын

Thanks! I will try to use that next time around. Seems so obvious, but I don't know what I don't know :)

@lars-magnusskog3983

3 жыл бұрын

@@mathcodeprint I didn't know about it either until recently. Happy to share :)

Thanks for this lesson, i am a beginner

Simple basic video yes but nonetheless you cover lots of good key features, Come to KiCad from Eagle, your video helped! Thank you

good video, i need to ask, why did you use all red, lines for the positive and ground wires? when you could have used green for the positive, i am confused, is it because you wanted all the traces on the lower side? thanks.

@mathcodeprint

3 жыл бұрын

Yes, i was trying to keep traces on one side.

Thank you, board of more than two layers, four layers or more

When you choose a symbol the footprint shows in the dark pane and you can use the 3d viewer. I am using kicad 6 and the pain says footprint not selected. What must be done to have the footprints show in that page.

coolest

im a beginner with pcb.. i want to make a keybaord... so did i get this right.. u first have to list all components and their connections in the "white" screen and then u have to design the pcb in the "black" screen and place and wirte the created components on it?

Good video. What version of your kiCAD? My kiCAD can't show the 3D design of my pcb and component design. I use kiCAD version 8,can you tell me how to show the 3D?

challenge, redesign this so that only three pins are required without using any additional components, just a simple rewiring change (pro tip: I can do this, so it is possible!)

When placing a component in Eeschema, how do you get it to connect to the dots on the grid?

@mathcodeprint

3 жыл бұрын

Snap to grid should be enabled by default. If not you can enable it. Right click a component and select align to grid when things are not working. You can set grid size in the right click as well.

Thanks for the video. Is there any way to choose desired LED color for 3 D view?

@andymouse

3 жыл бұрын

Size matters...not colour.

@mathcodeprint

3 жыл бұрын

Yes. But not easy. You have to modify the model if it doesn't exist. Afaik

@ 7.52 you do "FootPrint" a different way, but you don't show us how to get that tool ???

@mathcodeprint

3 жыл бұрын

Thanks, sorry about that. It is a confusing topic. I think a KiCAD footprints demystified video is overdue.

the components pins that do not have a small ball on it, are conected to the component ?

@mathcodeprint

3 жыл бұрын

Correct, the green "wire" connects directly to the component. Where you see a green "Ball" indicates the "wires" are connected. Whereas if two wires cross with no junction ( green ball ) there is no connection.

Please sir how can I get this software? Please kindly help me the link to download thanks I love ur tutorials

@mathcodeprint

3 жыл бұрын

kicad.org/download/

@njiforserge3979

3 жыл бұрын

@@mathcodeprint thanks so very much sir

assigning PCB footprint "manually" at the schematic level seem very painful!!! what if you had a schematic with 50 different "part types" ??

How did you get different colored LEDs in 3D? I have not been able to find any other color in KiCad for those LEDs other than red.

@mathcodeprint

3 жыл бұрын

I made them. I'll try to post them for ya. Basically it is a model i made in freecad and just set the colors.

@paulanderson1687

3 жыл бұрын

@@mathcodeprint That would be great. I was really surprised that I could not find colored LEDs in any KiCad libraries and I’m too much of a newbie to know how to make my own models or design component footprints.

In the video you turned the resistors around and you said it was because it would make it easier to hook up the traces. The resistor footprint looks symmetrical and polarity doesn't matter, so why did flipping it around make it easier to hook up the traces?

@mathcodeprint

3 жыл бұрын

Thought I answered this, but I guess not. I think I moved them around so they where physically arranged for a better trace. Even there there is no polarity, the ratsnest lines come from the schematic. New users like myself seem to just want to make sure all the ratsnest lines are hooked up. So when I see ratsnext lines crossing I just mentally want to uncross them. I think you are 100% correct and I didn't need to rotate them, but I think that ability to say, hey this component has no polarity I just just wire this ether way is something a first time user may not comprehend. I hope that makes sense.

hello, how can I add footprint for "GND" symbol

I wish my footprints were that easy. I had to upload them into the program and it all looks nothing like yours

Why do wires sometimes not snap to the component leads in Schematics?

@9336611680

3 жыл бұрын

Same question i have

@mathcodeprint

3 жыл бұрын

I have this happen as well, I don't have a good answer off the top of my head. I believe it happens when your snap distance is changed from the default and now no longer lines up. To fix it I usually change all the measurements back to 2.54 mm. If I nail down the issue I will post a video.

@Berghiker

3 жыл бұрын

@@mathcodeprint cool.

He sir how I can edit the led is color to make it green red and yellow like this one in the example that had shown I tried several times and can’t edit the color of it this make me lose my mind 😂

Can you save it as jpg format ?

How can you resize the symbol you just created?

@mathcodeprint

3 жыл бұрын

There is no resize for the symbol but you can zoom in on the document.

@Berghiker

3 жыл бұрын

@@mathcodeprint That doesn't help. I need to make a new symbol with the same proportion to the other symbols.

mine doesn't show the actual component on the board like yours.

@mathcodeprint

3 жыл бұрын

Not sure why, but it might be the version of KiCAD, also there is a setting in the Render that can turn off componenets. Finally, you have to have the 3d model library path added in the library manager. ( It was set for me but who knows )

Which KiCAD version is this one ?

What was the reason why you connected all of the LED's and then connected that wire back to the connector symbol? - big noob here

@bARZzZyy

11 ай бұрын

Additionally, why did it matter for the number 1 connection to be on top and that one that received the wire that connected the 3 LED's?

List of components plz?

How do you add 3D to your new custom component?

@PaulRandallMaker

3 жыл бұрын

I added a brief video on how to do this, but basically you use the Library Manager for Components ( PCB Parts ) and add an entry in the 3D Tab that points to your file.

@Berghiker

3 жыл бұрын

@@PaulRandallMaker Will try that.

Beginning of the video, you have 3 colors of LEDs(Green, Yellow, Red). How do you assign the color of them?

@mathcodeprint

2 жыл бұрын

I had to create custom 3d models. I took the step file and changed the color.

@user-rj1gs3lz2r

2 жыл бұрын

@@mathcodeprint I see.... I was wondering where I can find it but it was a custom-made. haha. Thanks.

de ce nu se afișează componentele in 3d wiew

Can you SHOW me how to start off with the ground plane first, on the pcb? ALL on one side of the pcb! No one can make a video and show me how to do this. Is it that hard to do? The circuit has 50 components.

@PaulRandallMaker

3 жыл бұрын

Just found your comment, I am not qualified as yet to do ground planes. My style is teach as I learn, so that I communicate from a "noob" perspective.

@Berghiker

3 жыл бұрын

@@PaulRandallMaker No problem. I found out how to do this.

GRACIAS.........👉 👷🇨🇱 👏👏👏👏👏👏👏👏👏👏👏👏👏👍👍👍👍👍👍👍👍👍👍👍👍👍💆.....................👉 🍷

If I look at the schematics and I look at the PCB then they don't match: Pins 1-2-3-4 of the connector in the schematics are replaced by 11-12-13-14 on the PCB Pin 11 of the PCB is connected to R3, where pin 1 in the schema is GND If you want to explain something, especially something so basic to beginners then make sure you show the right stuff, something which goes together. The way you made the video will nly confuse those beginners. Also, to get a good video you have to prepare your story: what do you want to do, how do you do that, step by step. It will become a much more professional video.

you have been using linux mint