Пікірлер

• 
  @smolbug29754 күн бұрын

  doesn't the metal band (lateral) go around the outside of the vertical supports? Otherwise they aren't working together and can move independently, if the band is on the outside they lock together and "contain" one another (and the concrete) much better.

• 
  @donnfishburn70849 күн бұрын

  How do you free rotate the view?

• 
  @donnfishburn708410 күн бұрын

  Clearest tutorial I've seen about FreeCad. I taught ACAD but now that I'm retired I have to pay A LOT for it. FreeCad is not at all intuitive, so, thanks. Do you have other tutorials?

• 
  @RandomTorok10 күн бұрын

  Awesome video. I tried watching another video and he was going so fast I couldn't keep up. Even with pausing ti was a pain. Could you do a very quick video on how to convert this to the files necessary to send to JLPCB. Another problem I had was I have kicad 8 so a few things were in different locations. I had to hunt for the text tool.

• 
  @codefossa22 күн бұрын

  Thank you so much for going over the basics. After this video I was able to go off and create pretty much anything that came to mind. I just needed to learn how to begin and this was perfect for that.

• 
  @Appregator25 күн бұрын

  How to install on windows. I unzip it and one gets a folder. Inside the folder is a bin folder. I click on freecad.exe and it takes ages to open and then does not run properly.

• 
  @oladosvinzuella699828 күн бұрын

  I LOVED IT TOO MUCH this is the only tutorial that I wished was longer

• 
  @simulation_freeАй бұрын

  great job！this example help me understand the routine of simulation using FreeCAD. Thank you very much.

• 
  @emmamcterrelly6936Ай бұрын

  challenge, redesign this so that only three pins are required without using any additional components, just a simple rewiring change (pro tip: I can do this, so it is possible!)

• 
  @pyotr576Ай бұрын

  Excellent

• 
  @stepannovotny4291Ай бұрын

  5 minutes of bla bla bla bla bla bla bla and 30 seconds of content!

• 
  @dbeelee8564Ай бұрын

  3:10 "When you click done, nothing seems to happen until you click OK." Tada ! Frustration disappears. Thank you !

• 
  @ocularcavity8412Ай бұрын

  THANK YOU SO MUCH!!!! this tool was making me pull my hair OUT!!!and thanks to the failure states and the ambiguity of the terms and their relation to what we are trying to do experimenting with is was NOT very efficient

• 
  @ronankelly4471Ай бұрын

  Thank you! Managed to print a replacement for my bike saddle bag using this as a guide. Salutations!

• 
  @markwilliams88922 ай бұрын

  Nicely presented and extremely useful.

• 
  @PaweSerwatka-in4zk2 ай бұрын

  Jesteś Wielki :) Pomogłeś Mi

• 
  @mr_tom_1_02 ай бұрын

  So around 1:23, where he's telling us to go to Patreon instead of telling us what he's actually _doing_, it's like this: Click New (top left icon) to get a blank document. Then click the white 2x2 grid icon, which is Toggle Grid (toggle Draft grid). Now you get some axes, no grid. Then (and this is the missing info -- KZread says this section is "most replayed", go figure) he's scrolling his mouse wheel like crazy and zooming out, from paperclip scale to house scale. If you look at the bottom right corner of the window, there are dimensions. The grid lines are 12 in apart (because you set them by following the "settings used" link... right?) so if you're zoomed in to 3/8 in you'll never see those lines. You need it to show _feet_, and really _tens of feet_, before you'll get a nice grid to look at. (Instead of the mouse wheel you can also do Ctrl-minus and plus to zoom. Macs use Cmd.)

• 
  @MahmoudEldefey2 ай бұрын

  He sir how I can edit the led is color to make it green red and yellow like this one in the example that had shown I tried several times and can’t edit the color of it this make me lose my mind 😂

• 
  @MrDaAsif2 ай бұрын

  Thanks

• 
  @beresfordromeo2 ай бұрын

  Hi Mathcodeprint I have installed your workbench but I can't figure out how to change the height and with of a plate. I can change the length but nothing else. Do you have any documentation for this? Thanks for all your great work.

• 
  @RobertJeffersonBased2 ай бұрын

  Thank you

• 
  @NewStreamLine2 ай бұрын

  Different Combo View (Solver messages etc) in FreeCAD 0.21.2? I'm a beginner.

• 
  @leviathanx08153 ай бұрын

  7:11 That is likely happening because you actually typed 6' 8"' , so it probably adds 6' and 8' and ignores the ", hence why you got 14' in the end.

• 
  @markpostlethwaite23403 ай бұрын

  I have tried to replicate this and my sketches are locked into position. can anybody help?

• 
  @craftannnahdesigns3 ай бұрын

  This video helped me a whole lot. Thank you so much

• 
  @jantwehncke15283 ай бұрын

  Great tutorial, but kinda nuts how complicated FreeCAD is. All this just for a bit of text on my 3D model.

• 
  @gregwoolley3 ай бұрын

  Excellent. Thank you.

• 
  @Larsbor3 ай бұрын

  ❤

• 
  @striveupward3 ай бұрын

  You have great intentions, but your presentation is disjointed, confusing, and you explain AFTER you have done the task ...so sad. Please practice before teaching. ......Blind leading the blind.

• 
  @abuzarchitsaz29533 ай бұрын

  So useful tnx a lot

• 
  @meisievannancy4 ай бұрын

  Try lofting a tubular part. This requires sketches with two rectangles and one is inside the other. I was using loft to create a rectangular tube which varied in dimension along its length. It worked well except at one section where the inner rectangle and outer rectangle crossed over at one loft section of the loft which made an apex in that section of a solid I wanted to 3d print. I really puzzled for hours trying to eliminate it. Eventually i found the reason. Freecad dies not loft double shapes via inner and outer shapes but it lofts double enclosed sketches in the order you create them. 😂😂😂. Wow. This was not obvious to me.

• 
  @kcirtap714 ай бұрын

  Hi, How did you get this rafter into your BasicShed files?

• 
  @domenicosurace75304 ай бұрын

  $fn=90; module holder_positive(h, w, l) { // base translate([0, 0, 0]) cube([w, l, 2]); translate([0, 0, 0]) cube([2, l, 8]); translate([w - 2, 0, 0]) cube([2, l, 8]); // wall R/ translate([0, l, 0]) cube([w, 2, h]); translate([0, l + 2/2, h]) rotate([90, 0, 90]) cylinder(d=2, h=w); // wall L translate([0, 0, 0]) cube([w, 2, h]); translate([0, -2, h]) rotate([90, 0, 90]) cylinder(d = 19, w); } module holder_negative(h, w, l) { // base translate([w / 2, (l+2) / 2, 0]) cylinder(d=8, h=8); // wall L translate([0, -20, 0]) cube([w, 20, h + 19/2]); translate([0, -2, h]) rotate([90, 0, 90]) cylinder(d = 16, w); } module holder(h, w, l) { difference() { holder_positive(h, w, l); holder_negative(h, w, l); } } holder(40, 35, 15);

• 
  @rmacster4 ай бұрын

  Great video. I absorb these bite sized videos much better.

• 
  @lebergerdesphotons45654 ай бұрын

  .21.2 is the version I just downloaded and it looks nothing like what you have there. Are you still using .18 and .19? Should I download the old ones? or have you redone cylinders on up to date software somewhere else? I doubt it, this was the first result to my search.

• 
  @mathcodeprint4 ай бұрын

  This is going to sound odd but, no, stay with your version a lot has improved. It is very hard to keep videos up to date. If you do want to watch thus video just use it to generally inform you of options availble not necessarily as a step by step. Sorry it isnt a good answer but it is the nature of the vast improvements over the last four years.

• 
  @calvinaizumiramadhan26854 ай бұрын

  Good video. What version of your kiCAD? My kiCAD can't show the 3D design of my pcb and component design. I use kiCAD version 8,can you tell me how to show the 3D?

• 
  @tbtitans215 ай бұрын

  Everything I print is directly converted to millimeters so I would say the units are millimeters and thats a nice thing to count on without having to scale

• 
  @liamthompson93425 ай бұрын

  This is exactly what I wanted to learn how to do, thank you

• 
  @cincinnatitypewriters5 ай бұрын

  GRRRR! When I start a new draft, to follow your directions, there's no "body" under "unnamed". Where did you create a "BODY"?

• 
  @fglatzel5 ай бұрын

  The author has never in his life designed reinforced concrete. Stop teaching people this non-sense. Since when is your shear reinforcing inside the main reinforcing? Do you even know what shear reinforcing is for?

• 
  @mathcodeprint5 ай бұрын

  Thanks for commenting. Nope I have never. This video is about using a tool in FreeCAD. About how to get a result. The maker of the tool was quite happy with the video. Most people understand the context of the video i am pretty sure, wont they use this as an engineering text ... i am sorry to have upset you so much.

• 
  @fglatzel5 ай бұрын

  @@mathcodeprint It's not about upsetting me, it's about "teaching" potentially dangerous methods. I suggest reading up on how rebar and structural steel design actually works.

• 
  @ronaldlogan35255 ай бұрын

  very nice. you almost showed me what I needed. How to REPLACE a text with mirrored version. Very handy for making maker stamps for ceramics.

• 
  @mathcodeprint5 ай бұрын

  So you need the "negative" of a text The idea being that the stamp leaves readable text on the surface of the ceramic. If you want to do it in Draft workbench, you would then move on to Part workbench and make an extrusion. This video is fairly old now and placing text on an object has been improved on part workbench.

• 
  @splinetech5 ай бұрын

  Thank you!

• 
  @mathcodeprint5 ай бұрын

  You are welcome :)

• 
  @demalenpire5 ай бұрын

  Hey, I was wondering what your initial setup settings were. I just downloaded the software, and the view/navigation isn't the same.

• 
  @mitch957225 ай бұрын

  This is a great video, would you be interested in making a new video with the updated feeCad? Thanks!

• 
  @mathcodeprint5 ай бұрын

  trying to get my act together :)

• 
  @ememeable5 ай бұрын

  Hi Sorry for the intrusion i am also a learner but have spot some irregularities with your approach or strategy the sketch tools are meant for specific tasks however you are deploying them without precision it is precise to use the curve surface work bench to attach sketch to a sphere or curved objects further to your current approach a sketch will not appear instantly unless it is placed directly on an object thus it keeps asking for reconfirmation when you do so. sincerely

• 
  @JernD5 ай бұрын

  Nice, I re-created it in build123d: from build123d import * with BuildPart() as p: with BuildLine() as l: m1 = Helix(8,12,10) with BuildSketch(m1^0) as s: Rectangle(8,3) sweep(is_frenet=True)

• 
  @mathcodeprint5 ай бұрын

  Nice ! I prefer FreeCAD, but I love the code CAD approach as well. I haven't hear of build123d. gonna check it out.

• 
  @davidprock9045 ай бұрын

  Now what about like a pancake coil with on even gap between the wrap

• 
  @mathcodeprint5 ай бұрын

  I'll do another short tomorrow :) maybe, but I would guess you set the growth property and set the pitch to zero.

• 
  @user-ds1bn7gn4p6 ай бұрын

  gmesh and calculix are now included in freecad by default i think

• 
  @mathcodeprint6 ай бұрын

  That's awesome if true, they where a bit fiddly to install.

• 
  @housebuilder19246 ай бұрын

  Best tutorial I've seen yet. You took your time to teaching as opposed to others. Thanks so much.

• 
  @canadianpatriot55776 ай бұрын

  It would help if each thing was actually explained. Example the FOR command. You demonstrate it as 10 10 100. What are each of these numbers? It made 10 cones, but if you change any of the 10 to 20 it doesn't make 20 cones, it makes 5 and spacing is based on what?