Kenmore Top Load Washer Inner Tub Replacement W10389328
Тәжірибелік нұсқаулар және стиль
Buy part W10389328 now: www.repairclinic.com/PartDeta...
This video provides step-by-step repair instructions for replacing the inner tub on a Kenmore Top-Load washing machine. The most common reason for replacing the tub is if it is damaged or leaking.
Additional washing machine repair, troubleshooting tips, help with finding your model number and part replacement videos can be found on our website:
www.repairclinic.com/RepairHel...
All of the information for this inner tub replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers, spanner wrench, hammer, 9/16" socket, 1/2" square drive
Buy part #S144CB now: www.repairclinic.com/PartDeta...
Buy part #P204CB now: www.repairclinic.com/PartDeta...
Buy part #38054 now: www.repairclinic.com/PartDeta...
Buy part #TB123A now: www.repairclinic.com/PartDeta...
Connect With Us!
plus.google.com/+repairclinic
/ repairclinic
/ repairclinic
/ repairclinic
Join our free VIP email list for discounts and money-saving tips: tinyurl.com/pnnh3be
Check out our blog: www.DIY.RepairClinic.com
Don't forget to like and comment on this video, and subscribe to our channel!
Пікірлер: 26
First video to finally show how to pull the drum out with the spanner wrench. THANK YOU!
@LMBee00
Ай бұрын
Only my Kenmore 100 series does not match these basket removal steps.🤷
Excellent video, great step-by-step explanations ... except for some little details, see below. My washer was pretty old (about 20 years), but they do not make them like the old Kenmore anymore, so I thought I'd repair it, baskets are pretty cheap. In my case, the basket hub had snapped from rusting. So my issue was that the spanner bolt was basically welded to the drive block and I had to cut it up in 4 (count 4) pieces with my trusty Dremel to finally disloge from the thead. I used a 1.5 inch cutting wheel, it took a few minutes, you have to cut deep (over 1/2") to make sure you get the flange at the bottom of the bolt (which is hard to see from the top). But I got the sucker out Remember, ALWAYS wear eye protection and gloves when using Dremel tools. The drive block + spanner bolt set is pretty cheap. I hope this can help someone with the same issue. Don't throw it away, these washers are built like tanks, just fix it. Also, while you are at it, grease the suspension springs and clean up the wash tub. My total cost was about $250, including all parts and the spanner tool which I didn't have.
Thank you so much for the info!
This video helped me immensely - however - I did need to purchase the Spanner Tub Nut wrench as mine was on really really tight. Was able to pick one up locally for 16ish dollars. Otherwise, everything was perfect. Thank you RepairClinic!!!
@repairclinic
Жыл бұрын
You're welcome! We are always happy to help.
I noticed that on the plastic washer and spacer that there appears to be lubricant/grease? Is this just due to it's location on the transmission shaft or should there be some applied to these parts? If so what kind and how much?
Greetings do you have to remove any back panel screws before lifting lid or removing cabinet???
My Kenmore washer is a little older than that one. So it is not like the dryer? Should I NOT try and separate the top from the sides with a screwdriver and pry the entire metal lid from the sides like a dryer?
I would have cleaned the outer tub nastiness on the outer tub liner while I was in there. Lol
Life saver!!!
@repairclinic
8 ай бұрын
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
How to know what size spanner wrench?
What size spanner wrench?
Mine is missing the plastic spacer entirely. And the collar on my inner tube looks mangled, like a fluted pie crust.
Hi, my washer doesn’t have the agitator as it’s an HE model. Do you know how to remove the retaining clip from the shaft? It’s a plastic piece holding down the shaft . Is there a video for this? Thanks in advance
@-Chrome-
9 ай бұрын
Did you figure it out, I'm having the same problem :(
For my Kenmore 70 Series washer (in video not 70 Series) parts manual it refers to what is being replaced here as the basket and the outer as the tub. Either Repair Clinic's terminology is incorrect or what ever model this is thats what its called. I watched this video because I want to remove my tub. This did not help as that I already have my "basket" removed.
i cant lift the inter tub up over the transmission shaft how do I get it unstuck?
@whoiskand
4 жыл бұрын
@@repairclinic This is not working or I am doing something wrong The inner tub has three plastic things coming thru the inner tub that seems to be holding the tub in But I can't depress all three at the same. Time
@tedthornton7791
Жыл бұрын
I'd like to know as well.
@tedthornton7791
Жыл бұрын
I'd like to know to.
@tedthornton7791
Жыл бұрын
I'd like to know as well.
Pretty good video - information-wise. But the "reassembly" instructions are definitely NOT showing a new tub. Come on, you're better than that.