pro tip: when putting a nut on like the one on the uppers with limited access, get a plastic bag and place the nut on one layer of plastic bag then push it into the box end of the wrench. the bag will take up the excess and keep the nut on the end of the wrench, now put it in place and spin the bolt to tighten.

awesome video!

Definitely getting

Just finish and made a video for my friends..hey well design easy to install. Have,all your tools really and a torque wrench. Much Mahalo Pacific Islander Beer Company

This is my new favorite tv show. #krxhammertime

I think all the sxs made need these upgrades in my opinion.

I'm a subscriber and don't know about these krx problems till I watch one of your how to videos which makes me feel like I better be safe than sorry ha. that being said can you put a link in here to your parts? Much appreciated

@fullaccessutv

2 жыл бұрын

i fixed it. Thanks markedmotorsports.com/krx-1000-aarm-tab-support-kit-upper-lower-must-have-p-389.html?zenid=68da883d407a32e60ef6a9a7deb11103

Hey great show, great info!I was wondering if you knew if the new 2022KRX has installed frame stiffeners and stuff like that. Has Kawasaki upgraded their known weak spots? Have you heard if they are coming out with a four seater and or turbo kit.

@fullaccessutv

2 жыл бұрын

So far my inspections of the 2022 unit they are exactly the same as the previous two years. No changes but minor items. As far as the turbo or four seater. There are rumors, there are rumors.

FYI: Checked out OBOR tires. When a Mfg. won't list tire weight on spec. sheet. They are generally much heavier than other tires. Example: 34" X 15 load rating is 700 lb. which is well under avg. UTV tire rating in this class. Reduce PSI and it drops more. Someone stated this is a 70 lb. tire. Too heavy for the overall spec. offered. On a KRX/2 you are O.K. with weight rating but who wants to run a 70 lb. tire? KRX/4 with a GVWR of 3100 lb. Not a good tire choice IMHO. System 3 tires may be Mfg. by OBOR but obviously at a higher spec. A lot of info. is required for tire choices... Some people watch your videos and consider your choice a proven / vetted one. Be selective which products you promote. ( Like your content, great presentation. ) Thanks

@fullaccessutv

Жыл бұрын

I agree. Some hide it. I’m not sure why there’s is not listed though. Those tires are actually lightweight, however they’re a little thin in the sidewall. I would not say that’s a great tire for a krx4. The new system3 450 and 370 tires seem like they have a very thick sidewall vs the older 350

@jemadv1594

Жыл бұрын

@FULL ACCESS UTV The system 3 - 450 is a heavy tire but is rated for 1719 lb. ea in the 35" and 1600 in the 33" that's a big jump from 700 lb. OBOR tire rating. But the 35" is 56 lb. and the 450 would be like driving your F-150 with E rated tires. Rough ride. I went with the RT320 rated at 1020 lb. ea. and their 35" is 43 lb. vs 56 lb. A 1020 lb. rating gives you 4080 lb. for a 3100 lb. GVWR KRX / 4 . Running lower psi reduces these weight rating numbers, so you need a little higher max rating to start. But the XC450 may be too much ? I went with Method wheels 1600 lb. weight rating, so if tires aren't as stiff and wheel takes a hard hit. It can handle the load better than a 1000 lb. rated wheel. Thanks

🇺🇸

Great video. I bought the 7 things every KRX must have. I have been getting it all put together. I did also buy the R1 industries frame stiffener. Using that should I put the lower brace on the a arms as there is already one there with the frame stiffener?

@fullaccessutv

Жыл бұрын

Thank you very much for the orders. have not seen their frames Stiffener. I am familiar with the superatv one, but there is really no need for one upfront. Too be honest their frame stiffener does not work with their skid plates. I would not use one. The front frame section of the Kawasaki is strong.

@HankMarducas

Жыл бұрын

@@fullaccessutv thank you for your response. I will hang onto those lower brackets and gift to someone. I found out the super ATV stiffener is the same as the one I bought. I am in the process of installing the super ATV 1/2 in skid plate. With your rear heavy duty skid plate I am going to just put the super ATV one over it? I believe this is what you said in the video.

@fullaccessutv

Жыл бұрын

@@HankMarducas Yes that is correct.

I have not had one apart, but why not have braces for the rear mounts of the front a-arms as well? Do the holes not wallow out, or frame bend on a front tire impact? Just curious. No complaints or problems with what you're doing.

@fullaccessutv

10 ай бұрын

We do make that brace as well now

I purchased the upper and lower A arm brackets. After installing them i noticed a big difference in the ride in the dry washes. It use to be really smooth but now it seems to send the energy from the right directly to the left and back and forth. You can feel the whole front end wobble. It seems to only happen during certain surfaces but ive never noticed it before. I have Shock Therapy suspension. Has anyone else experienced this?

@KRXBrandon

2 жыл бұрын

Do you still have this happening? I was curious to see if it went away after a bit of riding

@MrBrittg1

2 жыл бұрын

@@KRXBrandon I dont get out to ride as often as I would like. But a couple of weekends ago I rode out near lake Pleasant. This has been the 2nd ride since installing them. This trip I didn't notice it at all. Like i mentioned before it didn't happen but only on a certain sand wash run up near Bartlet lake. This last trip near lake Pleasant I was riding on more hard pack and loose dirt. I have purchased quite abit of upgrades from Full Access UTV and have been really happy with all the components. I cant tell you for sure if it went away as of yet but i didnt notice it last outting. I will keep the A arm supports installed and update if any changes.

@MrBrittg1

2 жыл бұрын

Follow up, this last weekend went to the race course where The Best of the desert race has an annual event. There wasnt a race event happening, just a group of us out running the course. Now back to the upper and lower A arm stiffeners. We were all running this course as if the race was happening, 45-65 mph. Hard pack, washes and deep rutted sand with whoops and everything. Some of the cars that was in our group were not your typical sxs. They had engines that were V6 and one was a V8, but no 4 wheel drive. I did not experience any of that left to right front end wobble that I was concerned about, that I felt up near Bartlet lake right after the install of the A-arm brackets. We had so much fun running that course and my KRX did awesome. There was one time I hit a serious type, combination sand with hard dirt type G-out and a wave of of earth came in over the windshield and covered us. Hit so hard I was concerned that I had to have broke/bent somthing. Got out and checked out everything up front. All was fine and was so pleased that I have installed the A-arm supports along with the shock supports and the rear skid plates. I dont know what that initial front end wobble was near Bartlet, outside it had be the surface of that particular stretch in that wash. All my buddies were really impressed with how this KRX performed out there on the race course near Parker AZ. I have installed other add-ons from Full Access UTV and will continue too.

I jist installed these and referred back to this video for torque info and you don't mention it. I know it seemed like the factory was 150 ft lbs to loosen. But what is your torque spec with this install?

@fullaccessutv

Жыл бұрын

Super tight. The factory are so hard to get off, I would tighten them the same way

@joesageser9707

Жыл бұрын

@@fullaccessutv thanks. And I did. Excellent product. Fits perfect

@fullaccessutv

Жыл бұрын

@@joesageser9707 thank you!!

Do these work with a frame stiffener

@fullaccessutv

2 жыл бұрын

Hello. Yes it does. However I don’t recall if their bolts are long enough but I think they are. What I like about our system better is it holds the driver and passenger together instead of relying on bolts that can easily loosen.

@sinned96

2 жыл бұрын

@@fullaccessutv well that's what I'm going with I'm the guy that you just talk to you on the phone here in Texas I forgot to ask you that question when I was on the phone

What size tires are on your machine

@fullaccessutv

2 жыл бұрын

34” Obor predators on this machine. A link that to them is in the description

@kuuipoalohalawler755

2 жыл бұрын

stock 31x15 I was going to put 35 put there is not enough clearance going into my garage.

What strength lock tight do you use, is it the red or blue

@fullaccessutv

4 ай бұрын

we use red

@jasonmontes9346

4 ай бұрын

@fullaccessutv thanks, I have my eye on a 2024 that I'm hoping to snag in the next couple weeks, are there any changes to the 24's that you know of that would make your must do's not fit.

@fullaccessutv

4 ай бұрын

@@jasonmontes9346 unfortunately, no changes

If you plan on installing a winch you better do it before you install the braces because they are completely in the way of getting the winch in place!!!!

What is the torque spec?

@fullaccessutv

Жыл бұрын

It is listed on our website. We offer free torque specs in the KRX information pages. But it’s very very very tight. Just as it was to get them off.

Torque specs?

@fullaccessutv

Жыл бұрын

Very tight. We have all the torque specs listed on our website under the Kawasaki information page.

your website security access sucks...tells me my time is wrong on my computer. its directly updated from Microsoft so its your guys certificate authenticator.

@fullaccessutv

Жыл бұрын

First I have heard of this.

@fullaccessutv

Жыл бұрын

got it all fixed. Thanks for the heads up.

I can’t get them unscrewed 😢 it’s so tight

@fullaccessutv

Жыл бұрын

they are all very tight. You will need a breaker bar or double wrench them.