Awesome Video man! you saved me a trip to a bike tuner. Followed all your steps and no problems at all. Just installed my slip on today and it sounds sick and runs awesome.

Just a couple notes (and a thanks for the vid!). The process is very easy. I did not remove the right side fairing all the way, just undid the back enough for stock exhaust to come off. Having two people for this is a plus, as one can hold the exhaust while the other disconnects the servo wires off the exhaust. Also, you can remove servo from under the tank as well, so keep your tank up until you've disconnected the harness connectors going to it as I think it's easier than going under the tail. The hardest part of this for me was getting that little black wire with brown tracer to come out. Other than that, it's about an hour job tops, no special tools needed.

Thanks for this. I had a lot of problems getting the wire out - I eventually took the decision to cut it leaving enough each end to solder it if I ever wanted to fit the std. exhaust again. It works, you can jut cut it.

Awesome!! I got it done in no time minus the setback with the stripped bolt on the muffler

Thanks the vid helped and I just finished my install without a problem. Good job!

Thanks man!!!! NO MORE FI C46 !!! I didn't know the right process on how to installa my aftermarket exhaust!!!

Awesome - thanks alot for doing this vid. I just did this mod tonight, had read up all the info I could find but nothing like seeing it done - I knew exactly what I had to do. Only thing is that I really had to pull on the B/Br wire to get it out of the plug (I got a pair of pliers on there and levered it out!) Other than that it's all sweet! Cheers!

Thank you for making this video! Very helpful!

just wanted to say tanks for the vid, i started to remove my exhaust and it was not as simple as i thought. thanks to you, i finally did it and she runs great! nice bike by the way, mine is the exact same color, and you have tool as your music, good taste imo, thanks!

THANKS HOMIE U R THE BEST WORKS FINE GREAT VIDEO . POLAND K6

Thanks man. This helped out a lot... I was going to do it but was unsure exactly what to do... problem solved.

Excellent saved me alot of time...great info...thanks

That's an old video, but thanks if you're still around here, it was useful. On my GSXR 1000 K4 it was exactly the same, except for the ECU connector. Here is a link if someone need to know what to unplug on K3/K4 : www.motopiste.net/t36813-comment-supprimer-le-fi-de-la-valve-d-echappement If you don't speak french, just look at the picture : unplug wire 1 = valve removal / unplug wire 2 = full power. Unplug both = smile on your face. Valve removed today, I'm going to try that on track tomorrow 🙂 it probably won't make a huge difference but I had an error code occasionally, which I suspect was caused by that getting stuck somehow.

Good...I'm happy that helped

Good video homie you should do some more...

dzięki w końcu po problemie i kontrolka nie razi :))

Great video helped a lot thank you

Thank you for the comment. It makes it worth while!

Very helpful,thanks a lot!!!!

Nice job!

Fast and good work.

Ok I found it. It is a black wire with a brown stripe. It is the black plug under your seat. The black wire with the brown stripe is the 5th slot from the left. Do Not unplug the excva servo because it will make the bike run in a safe mode. Hope that helps.

@claytonc101 I did some research and found that you pull the black wire with a brown stripe. Then remove the exhaust valve cables from the EXCVA servo. DO NOT unplug the EXCVA servo. That is why it is running in safe mode. Good Luck!

The way i did it was I put a sewing needle in the female end and inside there is little a plastic tab you can push up to release the wire. The trick is you have to pull the wire as you release the tab.

Very helpful video. Thank you. :-)

@08luisrod It gives you more power with an aftermarket pipe and reduces the weight. It's the black wire harness, black wire with the brown stripe, 5th one from the top left. Good luck!

hi my gsxr 1000 k5 has yoshi slip on and wire removed from ecu exhaust cables removed but the servo is still bolted on i thought i would remove as its just dead weight now if i un plug and remove servo will it through f1 light just wondering why the servo had been left on i bought the bike this way cheers for any info

THX for this manual

nice vid,very helpful is there a lost of torque without the excva ?

@cjaraza Make sure you didn't by mistake pull out any of the other wires and also make sure the harness is clipped in. Another thing you could do (I've done this before) is make sure the battery terminals are secure and check your fuses incase you popped one. I hope that helps.

it works on my 2007 GSXR1000, but black cable was in upper line of the grey socket, I removed and no more F1 code, thanks

Thank you, very straight forward video. The only thing that I am confused about is exactly what wire are you NOT supposed to cut or it will run on safe mode and where is it located? Thanks again.

Thanks for the video greeting ....

If you do not feel comfortable like me, you can order a Servo Buddy online for 60 bucks and connect it where you disconnected the servo motor from to remove it. plug that in and it will not throw a FI and no light will come on as it reads to the ecu that all is working normally.

okay... i already have an aftermarket twobrother exaust on my 2006 gsxr600... my f1 light will kick on... but when i turn the key on i can hear my servo clicking.. will i need to disconect that wire to get the f1 light off.....and disconnect the servo?

@homie6801 alright I pulled the black with brown strip wire. I don't know if it would be different on a 600, but the f1 light is still on and is blinding me.... does the bike run any different on safe mode.... and do I have to take the valve plate and everything out of the exhaust, then pull the wire?

Do the servo and cables have to be removed or can they be left in situ? Thanks for the video.

@theothistler pull out black wire with brown stripe, tape and secure it. The SET servo under the tank cannot be removed or it will throw a FI light.

I did some research but I couldn't come up with anything solid. I'll keep looking around and let you know if I find something for your 750.

@bigpig41 you don't have to it just makes it easier to get the grey one out

can I do this mod if I was just removing the can and running straight pipe?? Please help..Ill post a video if its possible

The 1000 is a totally different design. From what I found about your bike it might run in a safe mode if you unplug the excva, but if it hasn't done that at all I wouldn't worry about it.

Good video. I wanted to know exactly what this does? Does it have better flow in the exhaust? And would you happen to know what wire it would be for a k7 Gsxr 750

@claytonc101 Yes, but once you disconnect the wire it will cut off power to the servo.

@H82BLEGL It should be that easy it's just getting the locking plates off to get to the wire. It is the 34 pin ecu connector with the white locking plate and it is the black wire with a brown stripe. Good luck!

ola colega eu tenho uma k6 aqui no brasil , vi o video consegui ate tirar o escape e o servo , mas a cor do fio e diferente !! ai vc contou o 8º encaixe mas aqui a cor e diferente !! vc sabe qual a cor do fio eu tiro ?

@onesidequeens it is Tool off their album 10,000 days and the song is called The Pot

parabens muito bom mesmo:D

Hey homie6801 since when do we "rejet" a fuel injected bike? Did all this today for the third time and the only thing I can think of that helps is to remove the footrest. Gives a little more 'wriggle' room.

Is there anyone here on this channel that noticed a fallback in HP or Torque? Because its got to be there for a reason. Is it possible to order a muffler with a set valve in it? thnx in advance.

Great vid, i have a problem I can't unbolt the chassis mount, i turn and turn again, the bolt(motor side) is not accessible it is cover by a small metal plate.. WTF... so i can't access it to hold it while am unbolting the chassis mount ?? anyone got this problem ?

@KUTTA1NONLY

3 жыл бұрын

Yes, I'm experiencing this problem now. What did you do to get it off?

I'm not sure if the colors are different in other countries or not. I would double check suzuki in Brasil on that to be sure.

Rejet?..... FI bikes don't use jets. Unless your referring to something else, though I don't know of anything else using a jet other than one with carbs, just a thought. Great video btw, very insightful.

@homie6801 good video man! but when i did mine step by step like yours, after slip on is installed my bike won't start. did i miss something bro?

@KUTTA1NONLY

3 жыл бұрын

Did you figure out what the issue was?

song?? anybody plzz

Thanks a bunch ..just did a yosh trs slipo and it ran spot on. ...you made my day ...thanks again ..kind of a bitch doin it alone but gotter done ...

Oh yeah also the exhaust smells much better. ..keys fuel and helmet

Good vid fella, Just one question, why bother removing the EXCVA servo from the back end if it's been deactivated by the wire being removed seems like a lot of faffing for no reason, then you if you need to re-install the stock pipe you can, if you leave the EXCVA servo in place.

@mikenash4216

7 жыл бұрын

@gixerloon I was wondering the same. What did you do and how did you tidy away / protect the cable ends (if left in situ)? Cheers.

I don't think it is the same color. I searched on the internet but could not find anything on the color of the wire. You might try different forums or it might even be in your owners manual. Good luck.

@palespiral Your bike thinks you still have that servo and is running in safe mode because you didn't remove the wire. Remove it like in the video and that FI light should go out .

You might not want to do that. Your bike needs a certain amount of back pressure. You might have to rejet if you do that.

I wouldn't. I f you do it the way it says in the video you will avoid the FI light. I haven't had a problem with mine at all.

ola colega eu vi e é como vc descreve sim , e um fio preto com caramelo e marrom 8º fio do conector , perfeito valeu pela dica foi eu mesmo quem tirou , e saiu a mensagem f1 ,

GOOD, BUT THE MUSIC WAS SHITE