K24 engine cooling system
Автокөліктер мен көлік құралдары
crank part 1 - • K24 crank install (par...
crank part 2 - • K24 crank install (pa...
pistons part 1 - • K24 piston install
pistons part 2 - • K24 piston install part 2
oil pump - • k24 4piston oil pump i...
head assembly - • Installing valves on t...
head install - • Installing the k20 hea...
cam shafts - • Cam shaft install on k...
timing chain - • Installing the timing ...
timing cover/oil pan - • Skunk 2 timing cover /...
cooling system - • K24 engine cooling system
end build - • k24 end build
If a MECH A NIC video helped you consider donating to my patreon account to help support the channel. / the_mech_a_nic
or my paypal
paypal.me/jonathanrenteria1986
THE MECH A NIC’s amazon store ,here’s the tools I use
www.amazon.com/shop/themechanic
THE MECH A NIC’s Instagram page
/ the_mech_a_nic
THE MECH A NIC’s facebook page
/ the-mech-a-nic-1356996...
Thank you for watching my video, I appreciate the support !
Пікірлер: 172
The sound effects had me looking for a cat in my damn apartment. 🤣 Hahahaha.. your a fool for that one🤣👈
@themechanic6117
5 жыл бұрын
😂😂👍
@vernonyowe30
4 жыл бұрын
and i thought it was from the tool when it reaches the torque limit lol
Great tips! My only recommendation is I would suggest the silicone spray very sparingly on the hose connections. The silicone sprays I have used leave an oily film that I wouldn't want in my coolant, so I apply only a very light coating to the fitting the hose goes onto with my finger. Keep up the great work! 👍
Ohhhh shiny new parts! Looking good! And you better not put that Hyundai oil filter on it! ;)
@themechanic6117
5 жыл бұрын
You can't tell me what to do ! 😂😂👍
Looking great Jonathan! Love the shiny bits! 😍
@themechanic6117
5 жыл бұрын
Thanks! She sure is pretty 😍
Thank for your videos bro it's helping me understand the different systems of the engine
@themechanic6117
5 жыл бұрын
No problem. Its simple once its all broken down into sections
Nicely done and quite pretty :) yes there's a torque for every fastener if not I use the universal torque chart for each bolt specs as a guide. 👍
@themechanic6117
5 жыл бұрын
I didnt want to over torque lol. Someoneleft a comment with the correct torque spec and it all done. Had to tighten it a bit more 👍 Thanks for watching
Thank you for skipping the cat on those last 3 base mount bolts.
Really enjoying your build lad 👍
@themechanic6117
5 жыл бұрын
Thank you. Thanks for watching👍
😂😂😂😭😭...That fucking cat kills me every time with the meows
nice build, building a k20 rn for my ep3
@themechanic6117
Жыл бұрын
Nice, I just dropped this engine in a crx.check my playlists
Whats the part called for the s2000 thing?
Hahahahaahahaha that freaking cat torque wrench sound cracks me up 😂, engine coming along nicely , of course I’m sure it’s already running , just responding as if i was watching this video 4 years ago ....my wife thinks I’m nuts cause , she keeps hearing your videos in the back ground and wonders what the hell am I watching..this what happens when your stuck home during a pandemic 😷
Another great video, man.
@themechanic6117
23 күн бұрын
Thank you !
meowings hilarious lol
@themechanic6117
5 жыл бұрын
Some ppl dont feelthat way. Cant please everyone lol
@fiatmonkey4012
4 жыл бұрын
Sounds like a sick cat. Funny though!
@jorkygonzalez720
4 жыл бұрын
Tree House 😂😂😂😂
Hello how you doing great video I got a question what is the s2000 parts call or any part number on it
I appreciate this series man,it like to see the a break down video of cost when ur finished 👍thx
@themechanic6117
5 жыл бұрын
At this point im over $8k...
@georgebonney90
5 жыл бұрын
Holy Shit
@themechanic6117
5 жыл бұрын
Exactly... Still have to buy a $1200 intake manifold and some injectors... My wallet cries
Great vids, always wanted to build my own engine. How to you find the torque specs ?
@themechanic6117
4 жыл бұрын
Thanks for watching. I have a chilton repair manual that i look into for specs . if i cant find it in the book the internet really helps.
You wouldnt have the part number for the oil cooler housing
Yo I have a question , I have a k24a2 and I bought the plug n bracket that goes in my thermostat so I can delete the heater hardline, do I need anything else? I know the k20s u have to plug the back of the head, do k24s not have that ?
Anyone have the part number to that pipe or fitting on the water pump or oring as well?
Loctite gasket sealant is also very good, I've been using it for years.
@themechanic6117
5 жыл бұрын
Good to know 👍thanks
Hey bro, You dont need to put Teflon tape if a fitting has a o ring or a jic style fitting. Just letting you know koo video tho
@themechanic6117
4 жыл бұрын
Thanks for the info. 👍💪
How do you took the oil filter housing off to put the rsx one on?
@5:30 what are you putting on the engine? I know it looks like a fill up thing. Is that necessary?
The cats! 😭😭😂😂😂😂😂
@themechanic6117
4 жыл бұрын
😂thanks for watching
@MigzNthings
4 жыл бұрын
@@themechanic6117 I'm actually doing the same thing sometime this week.. what did you use for that rust dissolving on those bolts.. I have an array of bolts and pieces that need that sort of attention Migz P.s. my build is going into a DA integra
👍👍
Nobody talking about them weird torque noises 😂😂
Haha the cat
Could this work with oil cooler parts from the 06-11 civic SI?
Electricity...or vapor honing. Waiting on my vapor honing equipment..seen it do wonders.
When putting a Type S water pump and housing on a K24, is there anything else that needs to be changed? Do belts and accessories all line up?
@themechanic6117
4 жыл бұрын
Im using the ktuned alternator relocation kit so i cant speak for oem parts but i believe the belt n accessory still lign up
What is that stupid noise you make when tourqing down a bolt
Does the k24 oil cooler sandwich work on the k20?
Might sound like a nob question but the water neck on the side of the motor, what are you eliminating buy using that part? Just the fill port for the radiator? Is this used so the radiator can be tucked. Probably a dumb question but haven’t found the answer
@kudzy11
3 жыл бұрын
High point in cooling system,easier to bleed?
Did you add silicone on the water pump pulley or only on the housing?
@themechanic6117
3 жыл бұрын
Why would you put silicone on the pulley? I only added silicone to where the housing meets the block
Can you please tell me what the name of the part that you used from the s2000 ?
@themechanic6117
4 жыл бұрын
In this video i put the part number for that part kzread.info/dash/bejne/l3-ZptKre5a-h6Q.html
Damnn bro what rust disolver is that? The one I’ve using gives me the same results but it takes 10x longer
@themechanic6117
4 жыл бұрын
Rustoleum rust dissolver. Got it from autozone
The hose at 11:47 is backwards i believe. One side is shorter, it’s supposed to go at the bottom. The longer on top, then the hose wouldn’t be so kinked how u have it
@themechanic6117
2 жыл бұрын
I tried it both ways. It fits the same
For these 3 bolts and 1 nut you should have applied 33 lbs torque instead of 20... thats 44 newton meters, really good tip about the small passage, i didnt knew it, but not sure if that is enough to make the components stick since you just "masked" the surface with silicone, question: did you applied silicone on both sides right? I
@themechanic6117
5 жыл бұрын
Ill re torque it to 33lb ft, thank you for the info. Yes i applied silicone to both sides 👍
Whats the name of that bad ass rust dissolver?
Do u really need to install the oil cooler when doing a k24 head k20 build?
@themechanic6117
3 жыл бұрын
No you dont
@Onelovej
3 жыл бұрын
The mech a nic thanks Just got my RBC 1 head doing all the research 💯
@themechanic6117
3 жыл бұрын
Doing homework is important👍
Hey i have question if im running k24a4 wich coolant do i buy k24? Or k20? I see ppl buy k20 but not sure if everyone head is k20/k24 thanks
@themechanic6117
4 жыл бұрын
Which coolant? As in which antifreeze?
@JohnWayne-lp5ku
4 жыл бұрын
@@themechanic6117 no wich upper coolant housing do i need for my k24a4 head ? K24/k20 one right . I see ppl with k20 version so i was curios
I swear to God there's a cat somewhere in my bedroom
@themechanic6117
4 жыл бұрын
😂👍
@DAHBLIFE
4 жыл бұрын
You got yourself a new subscriber! Great video! gotta love the humor!
@themechanic6117
4 жыл бұрын
@@DAHBLIFE thank you
Also what oil k swap engines run? Synthetic or mineral?
@themechanic6117
3 жыл бұрын
You can use any one you want. I use synthetic
33ftlb for the water passage bolts and nuts.
What type of silicone did you use on the water pump hoysing
@themechanic6117
Жыл бұрын
If u remember correctly it was permatex ultra grey
Man watching this baked and I didn't notice the cat effect until half way though and I just thought it was my cat being a bitch. Then I remembered my cat died 5 years ago...
Hey to do that I need the water pump housing from type s or just the water pump from type s?
@themechanic6117
Жыл бұрын
You need the housing also
@juantorres-ln6lt
Жыл бұрын
@@themechanic6117 ohh okay the civic si with k20z3 use the same housing right?
subb'd cuz the cat likes his torque specs XD MMERRRRWWW
@darkcashyz
5 жыл бұрын
I died when the cat meows too funny hahahahahaahsahahah
@themechanic6117
5 жыл бұрын
😂👍
Part # for the o rings/gaskets???????
What’s the Honda s200 part number can’t find in the other video
@themechanic6117
3 жыл бұрын
11107-PT2-000
What are amazing and beautiful job and explanation outstanding I wish you would help me to build my K 20 Swap for EG :)
@themechanic6117
4 жыл бұрын
Thank you for watching and your comment. Lol you can do it! I got faith in you 👍
@sanyok7777
4 жыл бұрын
Faith is awesome !!!but Tools experience knowledge confidence that makes the whole game :)
@erocker78
4 жыл бұрын
Sometimes big jobs are not easy for the DIY mechanic. Sometimes jobs seem too difficult and its discouraging but you make it look so easy. Your videos are really interesting and inspiring. I just bought a bunch of tools. It should make my next repair and project a whole lot easier.
@themechanic6117
4 жыл бұрын
Having the right tools is half the battle! 💪👍
@erocker78
4 жыл бұрын
@@themechanic6117 definitely makes a world of difference in the level of difficulty. I can't wait to buy my next project car. Most likely another old Honda of some sort. Havent fully decided yet.
Just a heads up dont need ptfe tape on compression fittings it does nothing. It seals on the 37 degree flare, not the threads. Not being anal just a heads up to save the tape for pipe fittings an pipe fittings only 👌 good video tho bro.
What brand thermostat is that ?
@themechanic6117
3 жыл бұрын
Ktuned thermostat
Oh, my. I've fallen in to the trap, another cat video on KZread, ha ha ha.
@themechanic6117
3 жыл бұрын
😂😂 it's a trap !
Why the need for aftermarket cooling system?
@themechanic6117
3 жыл бұрын
This isnt aftermarket. These are original honda parts
Can you install one of those on the Honda CR-V 05 just wonder
@themechanic6117
4 жыл бұрын
As on as you have the plug to pull out so the s2000 part could be installed it should work. Youll need all the pieces
@thexflexclan
4 жыл бұрын
The mech a nic ok 👌 I will check if I have the plug it should be up right on the oil housing right but the water pump it’s different doesn’t have the plug where you put the hose on the top
@themechanic6117
4 жыл бұрын
@@thexflexclan youll have to change the water pump and the complete housing from a rsx S
@thexflexclan
4 жыл бұрын
The mech a nic i see the plug but I don’t know if you can just put the the other part that connecting the hose hey I have a question i recently replace my rear differential fluid on my Crv but even noticed long before replace it the rear driver side tire it slips like on wet road while turning well not turning just a small curv the tire start to slips then the steering wheel shakes a little bit but I don’t know it’s that normal never have an 4wd car before so I don’t know plus got new tires as well I won’t do it in high speed just like when driving on 40 mph or 30 something like that
@themechanic6117
4 жыл бұрын
Im not familiar with the awd on the crv, sometimes its normal for only one wheel to spin when you loose traction
What rust remover was that?
@themechanic6117
4 жыл бұрын
Rustoleum rust dissolver
How you manage to place that water pump housing o ring??
@themechanic6117
3 жыл бұрын
Im not sure what you're asking me..
@WMautoservice
3 жыл бұрын
@@themechanic6117 youre placing it at second 0:50
@themechanic6117
3 жыл бұрын
It should just pop into its groove
Wish you would have shown removing of the bolt for the oil filter housing
@themechanic6117
2 жыл бұрын
Just put a socket on it that fits and Remove it
@sentree9857
2 жыл бұрын
@@themechanic6117 for the threaded bolt that the oil filter originally spins on? I see nowhere a socket could fit. I’m reading people either use the double nut trick or just use a pair of vice grips but I’m having trouble with mine
@themechanic6117
2 жыл бұрын
Mine has a hex that I use a socket to screw on if I remember correctly. I remember now, I'm pretty sure I had to use vice grips to get it to unscrew. It'll damage it so make sure you have your new parts
@sentree9857
2 жыл бұрын
@@themechanic6117 I finally got it. It was a pain but a big ass pair of vice grips did the trick. I wonder how much of difference running this oil cooler helps? I figure with me being down south where it gets hot as hell and I’ll be running the car a bit it should help a lil.
@themechanic6117
2 жыл бұрын
It's not as good as a aftermarket oil cooler but it's better than nothing
What is the part number of water pump with water cooler?
@themechanic6117
3 жыл бұрын
Just buy a water pump for a acura rsx type S
Part # of the hoses your using?
@themechanic6117
5 жыл бұрын
You can find them on ktuned website and hybrid racing website
@kevinyang8205
5 жыл бұрын
@@themechanic6117 What bolts did you use for your k20/k24 timing cover, K24 or k20? And the k20 oil pan was k20 bolts?
@themechanic6117
5 жыл бұрын
The skunk2 timing cover came with its own bolts but if youre using a oem k24 cover you can use the k24 bolts. Id imagine the k20 bolts are the same. The oil pan is from ktuned so i ordered the short bolts that are required. If you have aluminium oil pan and are upgrading to steel you cant use the bolts for the aluminum pan. Theyre too long
@kevinyang8205
5 жыл бұрын
@@themechanic6117 Thank you
How mm diameter for oil cooler pipe?
@wakpey
4 жыл бұрын
In video 9:49
wassup bro, what is the s2000 part called (oil plug) or can you provide a part number
@themechanic6117
Жыл бұрын
Someone has asked this question before. Please check the comment section
@my93foxmustang1
Жыл бұрын
@@themechanic6117 so instead of telling me, you make me search for it... lmao...
@themechanic6117
Жыл бұрын
Because I don't know it, I'd have to search as well. I can't remember every part number. S2000 fitting part number- 11107-PT2-000
Parts numbers from those k tunes cooling hoses..
@themechanic6117
5 ай бұрын
Easiest way to find them is on ktuned website
Theres a cat in my house somewhere I know it
Meow meow to spec lol
@themechanic6117
2 жыл бұрын
😁👍
S2000 fitting part number- 11107-PT2-000
Dude you didn't say anything about the super long stud
Those clamps looks loose. Definitely going to leak forsure
@themechanic6117
2 ай бұрын
They're not loose and I've already pressure tested it . No leaks
Wassup with the cat 🐈 noises ???
@themechanic6117
Жыл бұрын
Just a bit of humor
Jesus man that meowing. I can't watch
@themechanic6117
5 жыл бұрын
Sorry. Catch you on the next one
What’s with the cat noises?
@themechanic6117
Жыл бұрын
Just for humor
@hollywoodjoe3259
Жыл бұрын
@@themechanic6117 ohhh 👍
Lmao
😹
Wtf with the cat
1st BOOM
I hope you will use Evans waterless coolant in this engine. If you dont know about it: www.evanscoolant.com/ It is very good.
The cat noises were funny the first 100 times. Jesus christ you over do it on every video man smh
@themechanic6117
3 жыл бұрын
Theyre my videos and i want to have fun making them. I'm sorry you feel that way
@tylerb9471
3 жыл бұрын
More power to ya buddy. By the way, you don't need Teflon tape on tapered fittings or fittings using an Oring. Good luck on the build 👌🏼
@themechanic6117
3 жыл бұрын
Just some extra peace of mind with the tape 👍 thanks for the tip
Meowing got annoying.
@themechanic6117
5 жыл бұрын
Sorry for the inconvenience
That meow 🐱 is annoying no more of that please
@themechanic6117
5 жыл бұрын
Sorry for the inconvenience
Unsubscribe due to stupid sound effects
@themechanic6117
4 жыл бұрын
Bye
@yonodc5705
4 жыл бұрын
Bye bitch