I've been having problems with my X738 . Definitely going to test it

Great info on upping your lift power

@gotdeeres

11 күн бұрын

thank you.

Good video George, Thank for the information.

@gotdeeres

2 ай бұрын

Thank you.

You just got another subscriber. Thank you for this information.

@gotdeeres

2 жыл бұрын

Thank you for subscribing.

Thank you for your output show auto repair a lot of stuff makes it easier for me I'm very handy fixing things so they could save money on their John Deere tractor 445

@gotdeeres

2 жыл бұрын

I used to repair JD 425's and 455's. I took MANY K91 hydros apart. That was before I started my repair videos. The X485 is similar to the 445. I never wanted an EFI tractor after I bought a diesel 455.

Thanks for posting a video on this subject! I currently have an X748 and an X728 as well as a 4200 project tractor. I've had my X728 since new with the 45 loader on it, and I always say that my dealer may have shimmed it when it went out the door because it has tons more hydraulic pressure than my X748 which I found a good deal on it used a few years ago. I since switched my 45 loader to the diesel and changed my relief valve as called for, but I did not shim it. It does not run the loader nearly as effectively as my old X728 with well over 3500 hours did. So I'm glad I found your video, I think I will shim it soon. I just got a gauge for them so I will take preliminary readings on both units to see what their output is. Thanks, Kevin.

@gotdeeres

Жыл бұрын

I would test the pressure on the 728 to see exactly how much pressure it has. The factory spec is around 1000 psi.

@kevinrumsey3756

Жыл бұрын

@@gotdeeres 1000 psi on the x728, 900 psi on the X748. The shims I have are tiny little medallions with no center hole though. Makes me think I got the wrong shims.

Have a 445 with around 600 hrs. Put a CTC loader on it . I’m new to the tractor ownership thing, I don’t know yet what pressure I have,but will soon . The loader is only lifting around 300 lbs, and struggling. Not looking to break it but just to get a little less struggling. Saw your video of the 332, I think moving gravel on the drive . Your getting much more a consistent lift than mine . If I could get closer to that capability then that would put a smile on my day. I have a gauge just haven’t found the connection hose like you showed. Thanks for the video, just earned another SUB!!!!!

@gotdeeres

2 жыл бұрын

Thank you William. I need all of the subscribers I can get. LOL That just gives me some incentive to make more videos. The hose is a 1/4" hydraulic hose with male 1/4" NPT fittings on both ends. The hydraulic male plug is JD AM37983. First check the hydraulic pressure and let me know what it is. That little 332 was awesome with a loader.

@dillongates4520

2 жыл бұрын

Yes mine does the same thing u will need to add a shim washers im going to get 3 shim washers so it will be about 1,100 psi

Awesome 👏 Thank You

@gotdeeres

2 жыл бұрын

Thank you. More to come.

@GotDeeres You're very thorough and methodical at these videos. Very helpful. Thank you for doing this. I have liked, subscribed, etc. 2 question - 1. Is it sufficient to test the hydro pressure only on one of the 4 fittings? In other words - all pressures should be expected to be the same, right? 2. Am I to understand that you do not have the THRV installed? Did you shim without this valve and the associated new freewheel lever? Thanks again.

@gotdeeres

2 жыл бұрын

1.) The pressure is the same on ALL foyr of the couplers.2.) I did not have a THRV installed.

300th subscriber

@gotdeeres

3 жыл бұрын

Thank you Chris. Now I just need 700 more subscribers to reach 1000. That is when my channel is monetized $$$.

Have you ever checked the charge pump at the charge pump port? Would like to see how and the procedure!

@gotdeeres

2 жыл бұрын

Yes, I have checked a hydro at the charge pump test port. All of my tractors now have hydraulic couplers, so that is much easier than getting to the hydro port. You will need to remove the fender deck and fuel tank. Then you just remove the plug and screw in the testing gauge. I made a testing gauge and it gives the same results as measuring at the quick connect coupler. The access plug is a O-ring boss male. Good luck finding that one. My testing setup is for sale. Just let me know.

Hi. New subscriber here. I appreciate the information you give. I just bought an x595 and my question is about the rear three point. Mine has a cat0 top link and cat 1 arms. Is this normal on this tractor? I purchased it used.

@gotdeeres

Жыл бұрын

The older cat 0 3 point hitches came with a AUC12534 top link. The new Cat 1 hitches came with a AUC12533 that would have a larger CAT 1 pin to connect to Cat 1 equipment.

Have a Simplicity XL with the Tuff Torq K92 w/4x4 and 540 PTO. It moves forward fine but when going in reverse it is very weak and barely moves. 1st culprit would be the Reverse Check Valve. Took them out but I have nothing to compare them to. Diagrams and pictures are very vague. I did take out the relief valve you posted on and the shims are very warn. I'm assuming that has nothing to do with the forward or reverse? Just curious if you have seen or heard of this?

@gotdeeres

2 жыл бұрын

My first guess is the reverse check valve is not working properly. Make sure that the tip of the valve moves freely and pops up. Manually press the pin in and out. Clean the ball and seat. The forward and reverse check valves are different. Make sure the Reverse is on the left side. The reverse valve has a small notch on the hex head. Next I would verify that the pedal linkage is not loose. You can download the technical manual for the K92 from tufftorq.com. The shims on the IRV are VERY thin. They are .2 and .5 mm. I would also suggest that you do the pressure test. Let me know what you find.

Hey I have a x740 the transmission is slow and weak in reverse and sometimes forward but mainly reverse the fluid level is good and clean just got it at an auction it doesn't look like it has been mistreated runs great any information would be greatly appreciated thanks

@gotdeeres

11 ай бұрын

How many hours on the tractor? My SWAG is the charge pump pressure is low. Since you have no idea if or when the Hydostat fluid was changed, I would first change the fluid and filter. The tractor comes with Low Vis Hygard, but regular Hygard is also an option for warmer climates. I have discovered that a weak hydro will have increased pressure because of the higher viscosity of regular Hygard. I live near Atlanta and have always used regular Hygard in all of my tractors.

@EricEstep1228

11 ай бұрын

@@gotdeeres if I'm not mistaken around 160 hours the fluid looks very clean I adjusted the rod from the pedal to the transmission it would go really good in reverse but not forward so I adjusted it back the transmission does not make any noise will I have to take it to a dealer to get the pressure adjusted

I need a transaxle for an x475. I believe it had a k92. Would a k92 from any other models fit? I have some mechanical & fab experience, so if theres even a close fit with another model, I'd be ok with that.

@gotdeeres

2 жыл бұрын

K92's from other models will work. They are the same.

I believe the 400 series models had the K91 transmission. Would the pressure relief valve be located at the same place? Do they use the same shims?

@gotdeeres

2 жыл бұрын

Yes, the 4X5 tractors did use a TuffTorq K91 which was a proprietary configuration for just John Deere. It is very similar to the K92. The shimming parts and installation procedure is the same as the K92.

@ETPFilmMedia

2 жыл бұрын

@@gotdeeres Awesome. Thank you for the video. It really helps me out! I wasn't sure where the pressure relief valve was located so thank you.

@gotdeeres

2 жыл бұрын

@@ETPFilmMedia You are welcome. Please feel free to ask any questions that you or any other subscriber may have. I do not charge for information.............. Yet. Just kidding.

@ETPFilmMedia

2 жыл бұрын

@@gotdeeres LOL! Thanks again

Can you tell what a ctm441 manul is used for, it is on the front of the tm142419 as a reference !

@gotdeeres

Жыл бұрын

John Deere Component Technical Manual - CTM441 is a manual that provides detailed information on the repair and maintenance of John Deere equipment. It is a component technical manual that covers the following topics: “Engine - 4.5L (276 cu. in.) 6-Cylinder Diesel,”

@williamrobb2045

Жыл бұрын

Do I need this for my x758

I have a 2016 John Deere, the power steering is hard at low speeds also lift is lazy! Gets worse when it warms up. Got the tractor used, oil level is fine ! Going to work on it this winter, any help would be appreciated.

@gotdeeres

2 жыл бұрын

What tractor model do you have?

@gotdeeres

2 жыл бұрын

How many hours are on the tractor? Did you change the hydraulic fluid and filter? The first test would be to test the hydraulic pressure.

@williamrobb2045

2 жыл бұрын

Haven't tested pressure need to find that out!

@williamrobb2045

2 жыл бұрын

X758 with 1300 hrs

@gotdeeres

2 жыл бұрын

@@williamrobb2045 The factory spec for the pressure is 924 psi. That test will tell you a lot about the hydro's condition. The X758 has a K90 hydro with a 6.0 gpm pump while the K92 was 4.5 gpm. It does sound like a charge pump issue.

I want to find a way to add 2 more remotes. With possible float. Is it possible?

@gotdeeres

2 жыл бұрын

I just added two REAR remotes to my X740. They operate on the lower hydraulic lever with the float function. I will be adding a video showing how to do it. Adding another remote with a separate hydraulic lever would be difficult.

How many shims are you using in total?

@gotdeeres

2 жыл бұрын

I just added a .2 mm shim to the existing ones. I did not measure the existing ones.

could you tell me the part number for the shims my jd dealer dont seem to know nothing about them thanks

@gotdeeres

2 жыл бұрын

The part numbers are : M806205 for the 0.2mm shim and M805974 for the 0.5mm shim. I did show the part numbers in the video. They are shown in center block section of the parts diagram for the hydro. Parts person too lazy to look it up.

@paulleone8386

2 жыл бұрын

@@gotdeeres thank you will keep watching your video

Sorry x758 with 1300 hrs ,fluid and filter is good!

@gotdeeres

2 жыл бұрын

Did you change the hydro fluid and filter?

I made my pressure test gauge from parts I had on hand. If you would like to purchase one, Aux-Hyd has one for $55. www.auxhyd.com/Hydraulic-Pressure-Test-Kit-Bottom-Mount_p_106.html