Keep up the channel please. Love the content it helps me a ehole lot with my 4230 because jd wants over a hunded bucks an hour to do anything plus i have to tske it there. Can't aford that kind of stuff. Have to do things for yourself unless your made out of money and thats far from being me. Thanks for all the tips and knowledge.

@jonstevensmaplegrovefarms3754

2 ай бұрын

Thank you very much for the kind words

Thank you for this video..fixing to tackle this job on a 4240 deere wanted 4500 for this job...i apreciate it

I think the hardest part of rebuilding something like this is setting all the tolerances correctly. Sometimes I think the service manuals are not as thorough as they should be so it's great to see you work and have a few of these things explained. Thanks for the videos!

@jonstevensmaplegrovefarms3754

Жыл бұрын

In your head it should be by lunchtime I'll have this transmission together. In reality it's late in the evening

I have a couple of 4430 project tractors so I really appreciate these videos.

@jonstevensmaplegrovefarms3754

11 ай бұрын

Thank you

Thank you for share you experience nating better

Love dad's old tricks.

We usually used an old load depth shaft to drive those bearing cups out of the axle housing, with the notch on the end of the shaft laying across the cup just a few hits and its out. Good video keep up the good work.

@jonstevensmaplegrovefarms3754

5 ай бұрын

Ha yep, have 3 of them shafts in a drawer,

Keep up the videos! I just graduated from college and brought a 4640. Your videos have helped me fix some quarks. Thanks keep it up!

@jonstevensmaplegrovefarms3754

Жыл бұрын

Thanks! Good luck, 4640 is a fantastic tractor

Recently discovered your site. You make fantastic repair videos. In this video, you are removing an inner race with a slide hammer, and it works. A good trick; run a weld bead around the inside of the race. The weld draws the race inwards, and it will fall out. Especially with old eyes, you have to be careful to weld the race and don't weld the race to the housing. On thin races, be careful to not weld to hot in the middle. It will stick the back side of the race to the housing. On thin races hold to the thicker edge. It doesn't take much weld for this to work. I will sort of introduce myself later.

@jonstevensmaplegrovefarms3754

Жыл бұрын

Welcome! Nice tip! Yep that is what I was welding here! Funny story is I did weld a thun race that I did not expect to be thin. Welded it solid to the cast housing

Show us the work while the repair is going on. You are very talented. Thanks

@jonstevensmaplegrovefarms3754

6 ай бұрын

I will work on it. I haven't been because these are customers' equipment, and I don't want them thinking I am wasting their time.

Thank you Ihave to fix my 4435 due to hydraulic not working same body say its charge pump

You are realy helping me out with your videos , and it is fun to watch at the same time : )

@jonstevensmaplegrovefarms3754

Жыл бұрын

Thank you. Glad to hear.

You ask if you help , yes . And nice article in the furrow

@jonstevensmaplegrovefarms3754

6 ай бұрын

Thanks.

Good job!!!

Good job

Great video. When greasing the outside bearing, does grease actually go directly into the bearing or is it filling the axle housing first then forcing grease into the bearing? Thanks Jon

@jonstevensmaplegrovefarms3754

Жыл бұрын

Kind of both. I grease a bit than spin axle housing grease a little more. A good layer of grease at assembly goes a long way.

Shop looks to clean

@jonstevensmaplegrovefarms3754

Жыл бұрын

Ha thanks, I was complaining how dirty it gets, the more clean it stays the more any dirt shows.

Wouldn't it be easier just to buy a new tractor?😂

@M8Stealth

Жыл бұрын

He did. He's got a new 4430.

@jonstevensmaplegrovefarms3754

Жыл бұрын

No. For the 25k I am putting into the tractor I can't get much,

@TheScotto477

Жыл бұрын

Kase wants to drive it when done