No video

4640 steering pump repair.

Пікірлер: 27

  • @kevinferguson4163
    @kevinferguson41636 жыл бұрын

    Glad to hear you can spend more time farming and get stuff done. Like your videos. Hope you get time to do more videos

  • @WarrMatster
    @WarrMatster Жыл бұрын

    Doing one of these on a 4630 right now, definitely a lot easier to get out than the 40 series tractors.

  • @mikeosterloh8439
    @mikeosterloh84395 жыл бұрын

    Impressive and can sing to. No bitching or cussing that must be the fresh air.

  • @PAFarms
    @PAFarms6 жыл бұрын

    Nice. It may be green, but nice fix.

  • @leeroyexcavator9149
    @leeroyexcavator91493 жыл бұрын

    Nothing like the sound of a old John Deere running. 👍

  • @busyonthefarm
    @busyonthefarm Жыл бұрын

    Really appreciate your videos involving this era of John Deere! Helps a lot! I've got the metering pump out of a 4440, on the bench already. Leaking all over cab floor and top of trans case. Point(s) of leak not obvious. I've read over the test procedure in TM1182 but, I do not have the gear to test properly. Is there a quick and easy way to test this assembly for leaks? Shop air in inlet fitting perhaps... I know that the low pressure line was leaking due to age and degradation. I've got all the o'rings and seals on order but if it's only this shaft seal that would save me a lot of trouble as I don't have alignment dowels for proper reassembly.

  • @johnschwert1914

    @johnschwert1914

    Жыл бұрын

    Q

  • @joemorse257
    @joemorse2576 жыл бұрын

    I replaced that seal in a 4440 last summer. It fixed the oil leak, but I must have snagged a wire because 3 days later it went up in flames

  • @mrbill4187

    @mrbill4187

    6 жыл бұрын

    Joe Morse geez, I don't know who'd hire you.

  • @joemorse257

    @joemorse257

    6 жыл бұрын

    mr Bill anyone with half a brain in their head would be glad to have me work on their equipment

  • @leeroyexcavator9149
    @leeroyexcavator91493 жыл бұрын

    I am attempting this today to get it out. Mine is a open station 4030 so the steering wheel has been a bear! Had to get the fire wrench out and heat it so the the little plastic slip tube is now very much toast! But I got the wheel off now on to the rest of it see how it goes. 🥴

  • @jonstevensmaplegrovefarms3754

    @jonstevensmaplegrovefarms3754

    3 жыл бұрын

    Ha! Good luck

  • @leeroyexcavator9149

    @leeroyexcavator9149

    3 жыл бұрын

    @@jonstevensmaplegrovefarms3754 I got it all out and apart so now just clean up and putting it back together . I had to remove the clutch pedal on mine to get the column tilt bolt out. It was hitting the pto lever.

  • @leeroyexcavator9149

    @leeroyexcavator9149

    3 жыл бұрын

    @@jonstevensmaplegrovefarms3754 You did say the side of the seal with the cuts in it or lips you called goes down right?

  • @jonstevensmaplegrovefarms3754

    @jonstevensmaplegrovefarms3754

    3 жыл бұрын

    The Spring or lipside always goes to the side of oil

  • @HaroldMoreland
    @HaroldMoreland2 ай бұрын

    What is the torque on the 4 bolts and nuts that mounts on the box?

  • @jonstevensmaplegrovefarms3754

    @jonstevensmaplegrovefarms3754

    2 ай бұрын

    If you're using a 9/16 wrench it would be 35 lb

  • @leeroyexcavator9149
    @leeroyexcavator91493 жыл бұрын

    My 4030 is leaking up by the steering wheel. I wonder if this is the problem with mine? My fix for the last year has been plastic folgers can wired to the column!! Lol. Cause they wanted 1000.00 for a steering valve!! 🥴

  • @jonstevensmaplegrovefarms3754

    @jonstevensmaplegrovefarms3754

    3 жыл бұрын

    Good chance just that rubber seal.

  • @hectormillar9035
    @hectormillar90352 жыл бұрын

    hi jon i need to know the hydraulic oil level of a john deere 4020 i'm from chile

  • @jonstevensmaplegrovefarms3754

    @jonstevensmaplegrovefarms3754

    2 жыл бұрын

    Welcome glad you made the trip from Chile! If I do a service here where you drop the oil and it changed the filters it would be about 11 gallons. It might change a little bit whether it's power shift or Synchro

  • @4065winchester
    @4065winchester3 жыл бұрын

    Could this have been done without removing from the tractor? Remove the 4 bolts and lift the steering column up enough to change the seal?

  • @jonstevensmaplegrovefarms3754

    @jonstevensmaplegrovefarms3754

    3 жыл бұрын

    I thought about trying it that way just to see.

  • @4065winchester

    @4065winchester

    3 жыл бұрын

    I have a leaky 4230 and wondered if it was doable that way.

  • @morleyperry7434
    @morleyperry74344 жыл бұрын

    how did you remove the steering wheel?

  • @jonstevensmaplegrovefarms3754

    @jonstevensmaplegrovefarms3754

    4 жыл бұрын

    Put the nut on the end of the threads flush. Put your knees or lift with a hand on the steering wheel. The hit the end of the shadt with an air hammer. Pops them right off!

  • @ryanreeder5897
    @ryanreeder58972 жыл бұрын

    I googled for the power steering pump.. I don't need to hear all the shit you're doing to the tractor. Fuck me, everyone likes to talk too much.