No more music or I will unlive myself! Cool stove though 😎

Saya sdh coba bikin,tanpa menggunakan tekanan,hanya mengandalkan gravitasi dan hasilnya disaat sdh panas dan jika menggunakan bensin maka api akan nyembur bertekanan tinggi dan akhirnya mati. Maka saya coba memakai oli bekas dan hasil nya bagus,semakin panas membara maka api semakin biru bara Cuma permasalahan tetep ada tekanan balik dan api besar sendiri lalu mengecil sendiri begitu secara berulang. Kesimpulanya hal ini sangat bagus sebagai inspirasi buat semua karena secara system sdh bagus dan masuk akal, hanya bth penyempurnaan ukuran pipa dan jumlah lilitan agar hasil maksimal. Good job bro 👍👍👍 Thankyou 🙏

@andikobra7980

2 жыл бұрын

Perbandingan antara oli bekas dan pertalite berapa bro??😁

@masgun99

2 жыл бұрын

@@andikobra7980waktu saya coba saya hanya pakai oli bekas sj om tanpa campuran ,tapi agak lama ngejos nya Nunggu lilitan panas baru wos howos howos joss 😂👍

@manualtech6673

2 жыл бұрын

siappp juragan... next time, jika ada ide lagi saya buat yg lebih bagus lagi pokoknya,..makasih banyak sudah mampir dimari..,

@manualtech6673

2 жыл бұрын

apakah ditambah perangkat lagi gan,?? misalnya oksigen atau apa gitu..??

@masgun99

2 жыл бұрын

@@manualtech6673 tidak usah d tambah apa2 kok.. krn oli yg di dalam kapiler akan mendidih dan menghasilkan gas,jd bs nyala seperti LPG. terimakasih bossku sdh mengispirasi Sukses selalu bossku 👍👍👍

Very impressive flame. I would put a one-way valve in the tubing right where you connect the plastic line. Weld (not solder but weld) a Y-joint to the one way fitting and install a needle valve to control the fuel feed. Make the rubber fuel line from an automobile duty hose with braided stainless steel covering. I know you are trying to make this on a budget but there are a few safety steps you really should consider.

@manualtech6673

2 жыл бұрын

yes sir, thank you for your correction.. that's right. I tried to minimize manufacturing costs, next time I will make safety valves such as valves and others for example..., so that in terms of security it can be really safe to use..🙏🙏🙏

@oddjobbob8742

2 жыл бұрын

@@manualtech6673 I didn’t mean it as a correction. I think your build is really very impressive. And in terms of keeping costs down, your method is excellent. But it would be a safety improvement, at, of course increased cost and complexity. For a manufactured stove with a very safe construction look at the MSR stoves (if they are still being made). I recall one model has a needle valve to control the flame and all of them include a steel mesh covering on the rubber fuel line between the burner and the fuel bottle.

Mwantaaaabb,,, suka banget ama yg kreatif2 gini,,,, terus berkarya,,, & di tunggu selalu ide2 cemerlangnya,,, MAJULAH INDONESIAKU, MAJULAH GENERASI BANGSAKU,,,

@manualtech6673

5 жыл бұрын

😁😁😁😉😉😉😉😉 shaaap makasih kak..., sudah mau mampir..🤗🤗🤗

@sumarsoherman9009

4 жыл бұрын

Bahan bakarnya apa...?

Good idea thanks for sharing beautiful have a nice day

@manualtech6673

3 жыл бұрын

thank U, youre wlcome my friend..😊😊

Таким же Макаром мы в детстве делали самогонный аппарат, немного конструкция была другая и маслопроводная трубка из Т-62 стальная,а так идея хорошая,возму на заметку.

@Danil.Haziev

2 жыл бұрын

Как я топлюсь водой и получаю халявную энергию! "Техосмотр печи с подачей перегретого пара после сезона эксплуатаций Вода горит!" ( На Ютубе ) "Форсаж печки перегретым паром Вода горит! Усеченный вариант" ( на Ютубе ) "Форсаж печи перегретым паром. Вода горит!" ( на Ютубе ) Экономия дров и углей в 2 раза. И жара. Вся сажа выгорает.

Super idea -when I was a kid ,we had a rocket stove with petrol! Made in home! His voice is a horrible "V1, V2 rocket sound. But idea is super! Now I am 68! Thanks!

@manualtech6673

Жыл бұрын

thank You Sir..😁😁😁

i just 2 say, awesome.. good idea, saya tunggu ide2 selanjutya bang

Great idea and I would like to make just a few suggestions. What if, on the tail end in which you have the tails end and the small hole, that you just have the end sealed but no hole, then on the outside of the top inner coil drill 16 holes of 1mm diameter at an angle of 50° from horizontal, and on the fuel supply line a micro fuel regulator to minimize the amount of fuel used for maximum effect for cooking. Also, on the fuel line where the copper tube meets the plastic fuel line a steel heat shield is mounted to reduce the risk of damage to the plastic fuel supply line, and finally, where the tail end hangs down under the cooker, suspend a small shallow dish into which a small amount of the fuel as a pre-heater for the fuel to bring the cooker up to temperature, and as one of your viewers commented, perhaps a flash arrestor would be a good safety idea. Otherwise, I was impressed...!

@manualtech6673

2 жыл бұрын

ok sir, thank you very much for the suggestions and input ideas you gave., hopefully next time i can practice it .., by trying to understand what you suggest, thank you for being willing to take the time to comment on my channel ..🙏🙏

@PhilipWright-pw3192

2 жыл бұрын

@@manualtech6673 It was my pleasure. I have been watching your videos and on the actual ideas you have a good lead on those who are trying to do the same. If you need any clarification on my suggestions please feel free to ask, and as we always say, 'to ask costs nothing'....! I do not have the opportunity to do similar things as you, as I am 67, retired and live in a first floor flat and have no garden or workshop. I am, as we say, a frustrated ex-engineer...!

@manualtech6673

2 жыл бұрын

@@PhilipWright-pw3192 ok sir, I still need a lot to learn.. moreover you are a mechanical engineer.. of course this is very proud for me.., of course your knowledge is very high and experienced in the field of machinery.. thank you very much sir, I am very happy to be able meet you.., don't be frustrated, and let's enjoy life as it is..

@manualtech6673

2 жыл бұрын

@@PhilipWright-pw3192 im sorry, my english very bad..😁😁🙏🙏🙏

@PhilipWright-pw3192

2 жыл бұрын

@@manualtech6673 If I was some 20 years younger I would have loved to get together with you on your projects as I can see that many of them have production potential, (with minor adjustments) which would make them winners. But alas, this frustrated and retired ex-engineer has to make do with carefully considered encouragement to make you better than I was. I was mentored by an ex-Luftwaffe pilot shot down over England, and I had the pleasure of working close with him, all his skills he taught me in a calm and relaxed manner while we made complex moulds and complex machinery for industry, if I came to a problem my mentor would say, put your tools down walk away, drink a coffee and have a smoke, then come back to the problem with a clear idea as to how to progress. His mentoring was perfect, and it gave me a pride in my work, so much so, that I would not put my name to my work unless I could pass it on unless the customer was completely satisfied, then I knew my skills we progressing and I could have great pride in my own skills and abilities that bring about that satisfaction of achievement. 'Do it right first time every time'...! Great Engineers create with the mind, heart and spirit, then that creation is constructed with the best two tools we have, the hands. Creation comes from the spiritual dimension, construction comes from the physical dimension...! My mentor also taught me to make every step 10°/° better every time so that constant improvement is made to improve the construction process...!

I would suggest a small candle right beneath the burner to make it safer to start. The flame also looked green, which might indicate burning copper- if it starts to burn through, then you might try forming the next around a small metal can, such as a tomato paste can, to create a protective layer. Most importantly, you should try to find a large metal container to use it inside of, such as a coffee can or a metal barrel, so that it will be less likely to either tip over, or spill fuel on other things.

@stonermagicinc.6343

Жыл бұрын

Just curious but is it magnesium that makes it burn green?

@versag3776

Жыл бұрын

But then oxygen/ air intake would be reduced

@versag3776

Жыл бұрын

@@stonermagicinc.6343 no it's copper oxide that burns green. Magnesium is a bright white.

Wowww ini keren bro, idenya sangat kreatif ...👏👏 Lagi cari2 mode kompor, ehh ternyata yg gini keren abis...

@manualtech6673

2 жыл бұрын

shiappp bang..., terimakasih banyakk ya,🙏🙏🙏

That's a great little burner man good idea and portable , getting plenty of heat to the kettle.

Saran, Lubang keluaran sebaiknya dikecilin Kalau mau praktis, pake gas elpiji aja, Kalau seperti di video (pakai bb cair) mestinya kawat tembaga nya dipanaskan dulu seperti lampu petromak biar keluar api jet nya.

@rendraadetya8849

2 жыл бұрын

Kalau oli, bisa digunakan tidak ya?

Muy practico el sistema de combustión. Felicitaciones amigo.

@manualtech6673

5 жыл бұрын

muchas gracias amigo..🤗🤗

Ini mah mesin jet.. 😁😁 tp auto skribkep dah, lihat hasilnya.. ditunggu mesin2nya yg lain bang.. Mantabh 👍👍

halo dan terima kasih banyak untuk video Anda !!!! Saya memulihkan bensin bercampur solar yang dibuang bengkel (karena orang menggunakan bahan bakar yang salah dengan mobil mereka di pompa bensin). Berkat Anda, saya bisa membuat kompor gas yang bagus untuk menghangatkan saya di musim dingin. Saya belum pernah melihat sesuatu yang begitu sederhana dan bekerja dengan baik sebelumnya! Sekali lagi terima kasih telah memposting ini dan hidup bahagia untuk Anda!

@manualtech6673

3 жыл бұрын

okey.. terimakasih sodaraku.. semoga bermanfaat, terimakasih sudah mampir ke channel seserhana ini..🙏🙏🙏

@ekoprasojo667

3 жыл бұрын

Wow👍👍👍prinsip kerjanya mirip petromaks...hanya anda sederhanakan....tanpa gunakan spuyer dan sarung petromaks....mantap...panas sy hitung setara dgn panas petromaks...WONDERFULL....

@manualtech6673

3 жыл бұрын

@@ekoprasojo667 siappp ndann... teeimakasih banyak, 😁🙏🙏🙏 malah saya ndak tau lampu petromaks..😅😅

مشروع في غاية الروعة والإبداع أخي الكريم ... تمنياتي لك بالتوفيق ... طور الفكرة لتصبح مشروعا رابحا تجني من وراءه أرباحا طيبة باذن الله تعالى ... سأطبق الفكرة بالتأكيد ... لك خالص الشكر على المشاركة بهذه الفكرة الرائعة. وكاقتراح اصنع هيكلا قويا وطبق الفكرة بصورة تجارية. ☪

@manualtech6673

2 жыл бұрын

آمين .. الحمد لله شكرا لك صديقي العزيز .. أتمنى أن يكون مفيدا .. وشكرا لك على ما تقدمه من اقتراحات وانتقادات ، الله دائما يسهل علينا جميعا ..

Super mantap !!! Sy bangga jadi rakyat Indonesia...smart kabeh otak profesor !!! Mantap mantap beribu mantap

@manualtech6673

5 жыл бұрын

terimakasih kak.. mari kita jd kaum yg berpikir, sebenarnya smua org Indonesia sangat cerdas dan pintar.., paling cuma males aja,..😁😁😁😁, masih banyak ide2 kreatif yg belum di temukan..

@arifbudi9553

5 жыл бұрын

manual tech.... ini baru solusi,,,

@manualtech6673

5 жыл бұрын

@@arifbudi9553 🤗🤗🤗🤗🤗 baru uji coba kak, ini masih mainan blom alat beneran...

Seems very very efficient.

excelente trabajo, gracias por sus ideas y creatividad

@manualtech6673

3 жыл бұрын

muchas gracias amigos .. ya tomándome el tiempo para pasar por este canal .

Maaf mas komen dkit. Klau pke slang ny. Pake aja anu slang las karbit. Tu tebal bahan ny. Asal tdak bocor aja slang ny. Tuk mompa ny pake air rator aja mas. Pompa udara tuk aquarium. Biar tdak capek mompa trus.. Klau nngk pke tabung oksigen rumah skit. Kpla ny tu bkin cabang kluar masuk. Klau mompa ny pake. Anu pompa speda trus pake spido angin biar tau tekanan udara ny trimakasi. Smoga brmanfaat..

@manualtech6673

4 жыл бұрын

bisa sekali mas.., itu sangat joss sekali.., pd dasarnya sama, cm klo mas bikin pakai peralatan itu,hmm itu kelasnya udh bukan main2 lg mas.. tp bener serius.. okey, siapp... mas bagus sekali idenya, like it!!

@mr.f1774

4 жыл бұрын

@@manualtech6673 mas mau tanya, jika bahan bakar diganti menggunakan gas bagaimana? Apakah aman dan tetap bisa jdi seperti jet?

@manualtech6673

4 жыл бұрын

@@mr.f1774 belum pernah coba kak,. tp secara tekhnis bisa.. namun sepertinya harus disesuaikan lagi input output oksigennya.. karena lpg tetap membutuhkan oksigen dr udara bebas pd saat proses pembakaran,

That is such a cool idea. Nice vid!

@manualtech6673

4 жыл бұрын

thank you..🤗🤗🤗🤗

@AS-ug2vq

3 жыл бұрын

How does it work, please explain

@sairamkiran

3 жыл бұрын

@@AS-ug2vq first pre fire the coil it heats and pressure creats in the coil. From one side fuel bottel is pressured with air. Bottle pumps oil to coil. And starts firing like jet engine.

Отличное изобретение, газ или жидкое топливо разогревается и происходит максимальное сжигание. Тем более показали всю работу профессионально. Молодец автор.

Excelente idea. Así se calienta el gas al máximo. BENDICIONES.

@manualtech6673

3 жыл бұрын

Muchas gracias amigo,.😊😊

super...

O tubo de entrada do combustivel que alimenta as chamas deveria ser maior para evitar aquecimento na mangueira do vapor de gasolina e nao correr risco, porem seu projeto foi otimo vou fazer igual. obrigado pela ideia.

@manualtech6673

5 жыл бұрын

oohh ... sim ... eu entendo um pouco sobre o que você quer dizer ok ok obrigado amigos ... esperamos que seja útil

I gotta try making one. This is so cool.

@manualtech6673

4 жыл бұрын

Yes, please.. But be careful and prioritizing workplace safety Hopefully useful.. Thank you so much friend.🤗🤗🤗🤗

@MagicGate814

4 жыл бұрын

@@manualtech6673 Imagine putting 3 or 4 of these together and using it to make stir-fry rice.

@manualtech6673

4 жыл бұрын

Will definitely be faster burnt 😁😁😁😁😄😄😄😄😄

Very good invention... thanks to the info..

@manualtech6673

Жыл бұрын

thank You sir...🙏😁😁🙏

Saran om. Klo pk fuel bensin dan variannya pk bor 0.45-0.51mm. Klo pk minyak tanah, solar diesel dan variannya pk bor 0.32-0.38mm. Untuk safety pk valve keran dan selang bensin/fuel. Untuk pressure dlm tabung bahan bakar jangan terlalu tinggi, cukup sekitar 7-8x pompa untuk menghindari potensi leak/bocor pd spot2 sprti sambungan. Anyway... well done

@manualtech6673

4 жыл бұрын

mantappp... jelas ini mas ronald pasti org teknik..😁😁😁 lengkap banget spesifikasinya.. hapal betul ukuran2nya, nice.. yg masih sy blom nemuin adl valve nya mas.. klo.bisa kita bikin aja sendiri tanpa ada yg beli..😁😁😁 biar semuanya adl memanfaatkan barang2 disekitar kita yg sudah atau tak terpakai.. pokoknya mas ronald luar biasa sekali.. terimakasih mas sudah mampir dan saran sangat membangun sekali..🤗🤗🤗

ESA luz deja vrillar en tu corazon Jesus dice ; yo soy el conocimiento de LA verdad de LA Vida eterna

That's good, but I think if you add a metal bowl underneath, it will help to ignite the fire, and prevent the fuel spreading around.

@manualtech6673

2 жыл бұрын

okay, thank You very much Sir..🙏🙏😊

The great vedio! thank you for sharing.

@manualtech6673

Жыл бұрын

You're welcome Sir...🙏🙏🙏

Музыка не менее эффективно прозвучала в этом сюжете. Не понятно, что за топливо, если это бензин, то трубку хоть в задницу всунуть, все равно будет гореть. Сергей Васильев.

Видео называется - Как быстро сжечь свою хибару.

100% verdadero Yo lo hice felicidades amigo

Creative video, thanks :)

what are you using for fuel?

@calysagora3615

2 жыл бұрын

My question exactly.

will the copper melt when you're cooking for a few hours ?

@demoaccount2392

10 ай бұрын

No, the heat us continuously transferred to the fuel that's what makes it vaporize. The temperature of flame is also too low to melt copper in this case

Luar biasa, ini membantu saya membuat kompor di rumah, saya sangat menghargainya, salam dari Meksiko

@manualtech6673

2 жыл бұрын

terimakasih sobat..🙏🙏

Great design, but shortly the heat will transfer down the copper to the plastic feed line melting it. Need some kind of heat resistant connector between the copper and plastic feed line

Muito bom, achei potente demais, vou seguir sua ideia e tentar fazer um mais fraco para usar no camping, como se apaga o fogo quando acabar de usar ?

@bernardo6422

4 жыл бұрын

Desculpa por me intrometer mas acho que é o corta fluxo que tem na mangueira de soro . Não sei o nome daquele negócio. Também fiquei sem saber como faço o esquema onde fica o combustível . Espero ter ajudado ! Fico esperando a resposta do tutor também 🙏🙏🙏

@manualtech6673

2 жыл бұрын

simplemente gírelo en la configuración de la manguera de infusión, señor.

@bernardo6422

2 жыл бұрын

@@manualtech6673 obrigado 🙏

@manualtech6673

2 жыл бұрын

@@bernardo6422 Obrigado novamente amigo ..

@PhilipWright-pw3192

2 жыл бұрын

Um interruptor de corte na linha de combustível

Really cool idea. I wonder if a home made HHO generator can be used as fuel.

@JG-lx5pm

2 жыл бұрын

NOT recommended, hydrogen is HIGHLY reactive and instable that is why is not as popular in transportation.

@TruthIsKey369

2 жыл бұрын

@@JG-lx5pm wrong, HYDROGEN alone isn't more dangerous than other fuels, quite the opposite, BUT HHO (Hydrogen+oxygen) is dangerous in any form whatsoever.

@gabrial3377

2 жыл бұрын

I got all of that. With a couple flash arrestors in place it would be a great experiment and a free use of water as power. I will be trying that. I drive my pick up truck on hydrogen. I'm still here, 20 years later.

Wla delikado yng gawa mo broo oo nga maganda ang apoy piro delikado yn bka sumambulat yn boom tpos tyo jan

Cool! the original jet boil maker found!

Saran aja bang.. Harusnya ada primingnya dulu. Jadi dipanasin dulu coilnya. Biar pas bahan bakarnya keluar udah langsung uap yang terbakar. Btw.. Good job lah

@manualtech6673

5 жыл бұрын

iya kak, kurang penjelasan juga sih videonya.. maksud sy biar langsung paham ketika sekali lihat videonya, eh malah banyak yg bingung kak... btw, makasaih banyak kak saranya yah, makasih udah mampir juga..

@ariemaulanaichsan1153

5 жыл бұрын

@@manualtech6673 Selow.. Saya pernah buat lebih bahaya daripada ini. Tapi kemudian nyari tau masalahnya yang bikin bahaya dimana.. Sedikit saran lagi untuk bahan bakar bensin, kasih lubang yang lebih kecil lagi. Kalau dengan spiritus masih aman dengan lubang 0,8/1mm..

@manualtech6673

5 жыл бұрын

@@ariemaulanaichsan1153 okey siap kak, kita se hobi..😁😁😁😁 wah ternyata indonesia banyak orang yg suka anti maenstrim, wkwk.. btw, sempat didokumentasi ga ya videonya kak siap siap..., in progress kak nyubi ini selalu belajar dan belajar pokoknya..😊😊😊

@achnasir

5 жыл бұрын

@@manualtech6673 bagian bawah kasih tutup kaleng buat priming bakal lebih mantab. Btw, udah coba dengan spiritus?

@manualtech6673

5 жыл бұрын

@@achnasir iya, itu juga bagua kak, udah pernah hasilnya bagus, apinya kadang berwarna hijau.. tp sayangnya mahal kak pakai solar juga pernah.., bagus juga kok.. tp timbul hitam2 sisa pembakaran.. btw nice idea

Мужик изобрёл паяльную лампу. Бугага.

@dymp1965

2 жыл бұрын

и довольно опасную

Lebih efisien pendorong anginnya pake kompressor angin aquarium, keluaran anginnya stabil. Dengan cara: 1. Botol kaca bekas sirup dilubang tutupnya (yang tutupnya ulir dari logam) 2 bagian, jangan terlalu longgar supaya selang bisa masuk tapi dengan cara agak dipaksa supaya selang itu sendiri menjadi seal sehingga angin tidak keluar. 2. Selang dimasukan yang selang pertama sampai dasar botol yang selang kedua cuma sedikit kira kira 5 cm dari mulut botol. 3. Selang yang sampai dasar botol masuk tungku, yang pendek masuk kompressor angin aquarium. Keluaran angin bisa diatur lewat selang yang terhubung ke kompressor. Ini sistemnya kebalikan dengan kompor gas bensin Untuk selang itu inlet bensin selongsong tembaganya kurang panjang itu bisa bakar selang plastiknya.. overall mantul👍👍👍👍

@manualtech6673

5 жыл бұрын

masuuuup pak eko, nice idea.. tp jgn botol kaca kak, sy takut nanti klo ada tekanan balik dri ruang pembakaran yg tdk terduga bisa bisa, tarrrrrrr...pecah...,hihihi.. pake botol plastik dlu aja krn masih ada toleransi mengembang ketika pukulan tekanan balik trjadi, tp konsep kakam pasti nantinya kebih rapi dan keren sihh...asli.. nice idea..beneran

@Train.Shotter

5 жыл бұрын

Botol cocacola/ sprite yang 1,5 literan om.. itu bisa nahan tekanan soda berarti juga bisa nahan tekanan balik..

@manualtech6673

5 жыл бұрын

@@Train.Shotter iya, kmrn pembuatan pertama kali pakai itu botol kak, bagus dr pada pake botol minuman mineral biasa.., itu kuat nahan tekanan volume besar bisa nampung bahan bakar dan udara lebih banyakk..

@rhenahanifahazzahra9616

4 жыл бұрын

@@manualtech6673 klu ga mau tekanan balik pakai Valve.

@manualtech6673

4 жыл бұрын

@@rhenahanifahazzahra9616 oh iya... benar sekali,...😁😁😁😍😍😍😘😘😘😘 tengkiyuuhh kakak...😁😁😁😁

Wow,nice work my friend 👍

... ещё один вариант походной горелки!-, единственный минус этой конструкции-, не регулируется подача топлива и сила огня!!!

Copper pipes will be damaged after a day or two, and it is better to use stronger metal or buy a single kerosene stove head, as it is stronger

Fantastic project

@manualtech6673

3 жыл бұрын

thank U brother..🤗

Seperti kompor mawar jaman pompa minyak tanah jmn dahulu prinsip ketjsnya .... Okey . Lebih di kembangkan lagi di perpanjang slang tembaganya ...jossssss

@manualtech6673

5 жыл бұрын

okey...siap kak, makasih yah dah mau mampir..😘😘😘

@ekonikochanel7548

5 жыл бұрын

@@manualtech6673 mantappp jiwaaaaa

Tell how many holes are drilled into the copper tube and how many feet of tubing you coiled up. What kind of fuel.

@manualtech6673

2 жыл бұрын

there's only one fuel outlet, sir, I don't really remember how many times I wrapped the copper, but the fuel I used in this video is gasoline..

JFC, without a flash arrestor this thing is extremely dangerous

@flightographist

2 жыл бұрын

@, maybe three turns would suffice to increase the pressure, this is a death trap.

@davidran9317

2 жыл бұрын

@@flightographist Is he still around? Crazy people do crazy thing's ☺️🥴🔨🙏

@manualtech6673

2 жыл бұрын

this is not a trap this is real like i did this video and i'm still fine guys..don't worry,

I like it. Good job.

Cerdas sekali. Bahan bakar di panaskan agar gampang di uapkan. Kasih tekanan dikit aja api lngsg biru. Mnatap pak aji

@manualtech6673

4 жыл бұрын

shapp... makasih agan, 😁😁 udh mampir

Just need a titanium pot now

@manualtech6673

2 жыл бұрын

Sorry for the lack of facilities, my friend..🙏🙏🙏

Меня одного уже бесит маликов со своей тупой рекламой?!?!?!?!?!? Видать бабки кончились жить на широкую ногу, раз подался в рекламщики потреблятства......

Sangat menginspirasi kawan, terimakasih sudah berbagi

@manualtech6673

4 жыл бұрын

oke.. terimakasih kak... sudah mau mampir 🤗🤗🤗🤗

👍👍. Sama dengan prinsip kerja lampu petromak jadul, bahan bakar minyak tanah. Tank yg berisi minyak tanah dipompa agar mengalir melalui koil tembaga yang berbentuk spiral, karena spiral tembaga mendapat semburan api shg minyak tanah menjadi panas dan berubah jadi uap (gas). klo dah redup cahayanya dipompa lagi.

@manualtech6673

2 жыл бұрын

yapp, betul sekali bang...terimakasih banyak sudah merespon video ini...salam, sehat untuk abang dan keluarga dirumah...🤗🤗🤗🙏🙏

Greetings friend from Venezuela, you have tried it with diesel and if the flame turns blue and what kind of fuel are you using in the video test and with gasoline it is not more ballatil I think diesel is safer I am going to do it but I will try diesel

@manualtech6673

Жыл бұрын

yes my brother, in this video test I use gasoline.. and sorry I have missed the most important part here .. namely the fuel and the canister .. but information for you, using diesel fuel can still produce very good fire and also safer..., so thank you very much brothers.🙏🙏🙏😁😁

@romilsonmagalhaes6487

10 ай бұрын

Eu tambem pensei nisso, usar oleo diesel. Se voce conseguiu, me avise!

BUENAS TARDES AMIGO, AMIGO HICE SU PROYECTO PERO LE HE HECHO ALGUNAS MODIFICACIONES Y ME HA FUNCIONADO PERO TENGO ALGUNO PROBLEMAS O ALGUNAS DUDAS PARA PERFECCIONAR LO, LA PRESION DE AIRE Y GASOIL TIENE QUE SER ALTA, BAJA O MUY BAJA? GRACIAS

@cesaraugustovelascogomez7060

3 жыл бұрын

USA ALCOHOL PARA QUEMAR, O INDUSTRIAL QUE LE LLAMAN...Y SI NO TIENES COMO BOMBEAR, NO TE PREOCUPES, IGUAL TOMARA FUERZA AL CALENTARSE Y TERMINARA RUGIENDO CUANDO SE EMBERRACA A QUEMAR...ASI LO HACEMOS EN CALI.

@manualtech6673

2 жыл бұрын

okey, perdón por no poder responder .. no dudes en mejorarlo por favor, ajuste la presión y la llama, porque si es demasiado grande será un gran desperdicio de combustible ... si la presión es demasiado pequeña, entonces el fuego tampoco es óptimo ... está bien, espero que ayude

Awas copot selang mu gus.. Mompanya jgn pake napsu. Sampean ncen ngene 👍👍

What about the plastic pipe? Won’t it melt . ?

@manualtech6673

4 жыл бұрын

yes, of course the longer the shorter the connection distance will melt ... then the copper pipe and plastic hose must be longer in connection .. or given a cooler in the form of a cloth that has been moistened ..

Meleleh tuh selang kalo lama nyala....

Extraordinariiiooooooo absolutely fantasticoooooooooo thank you for sharing this excellent video 😂😂😂😁😁😁😃😃😃😀😀😲😲😲😲😲😲😲👀👀👀👍👍👍👍👍👌👌👌👌👏👏👏👏👏

@manualtech6673

4 жыл бұрын

very much brother..😀😀😀😁😁😁, but, You're welcome..😁😁😂😂😂😂😄😄😄

Una pregunta Cuántas horas puede durar eso encendido puede durar 8 horas me gustaría saber

That’s great if you’re smelting aluminum.

@manualtech6673

4 жыл бұрын

will be very wasteful if the fuel is not made a tight furnace,🤗🤗🤗

i like your idea i will keep following your channel

@manualtech6673

Жыл бұрын

Thank You very much Sir...😊😊😊🙏🙏🙏

Good job brother

Selang infus y apa ga meleleh kepanasan bosku

@manualtech6673

2 жыл бұрын

insha Allah enggak gan, atao dipanjangin pas sambungannya juga bolehh biar aman..

Terimakasih 👍

@manualtech6673

Жыл бұрын

Sama-sama 👍 semoga bermanfaat

That'd be great for stir frying!!!🤤

Amigo lo hice y me a funcionado Gracias por compartir...

@manualtech6673

3 жыл бұрын

okey, gracias de nuevo amigos ..,

@manualtech6673

3 жыл бұрын

@Norman Valdes muchas gracias amigos .. saludos tambien desde indonesia

You pressurized the gasoline, why did you have to use all that copper pipe to make coil and heat the fuel unless using diesel?

@manualtech6673

5 жыл бұрын

hehe ... sorry true, at first I thought that the longer the pouring evaporation will give maximum results, apparently not, it should be to evaporate the gasoline only need a little shorter pipe windings. not like to vaporize diesel fuel ... thank you friends for your advice.

@99nouns

5 жыл бұрын

I think you might have discovered the diesel stove, if you still have it you should try it with diesel to see what kind of result you will get.

@devinepicture8359

4 жыл бұрын

This is good for waste oil

@AS-ug2vq

3 жыл бұрын

Compor = kerosene or diesel type 2, it's not as easy to light like gasoline.

Bagus juga idenya hanya saja bb minyak tanah mahal per liter nya

@manualtech6673

3 жыл бұрын

siapp, besok kita bikin minyak sendiri mas ya,.. dan terimakasih banyak mas Yana sudah mampir dimari..😁😁

@primaputraarisiantama2336

3 жыл бұрын

Ganti solar murah

@Winena

3 жыл бұрын

Ganti sollar bro

@sheberstov6604

3 жыл бұрын

Всё что здесь показано -- первый курс Советского института по прямоточным реактивным двигателям -- самыые азы

@manualtech6673

3 жыл бұрын

@@sheberstov6604 спасибо друзьям за предоставленную информацию .. Могу ли я немного поучиться в Советском институте? если разрешено, где я могу найти канал ?? Меня всегда поражало советское государство.

Отлично горит ,но ведь есть паяльная лампа ,она компактней и безопастней👍

Ficou top , precisa de alguns ajustes com a mangueira , mas as chamas ficou top ok 😂😂

15 минут разжовывать принцип самодельной паяльной лампы ! ЗАНУДА !!!

Lose the music and let us hear it run.

Make one for vegetable oil that doesn’t need pressure to work, just gravity feed. Then you will achieve something useful.

Good one.. This is what they use in petromax lights

@manualtech6673

2 жыл бұрын

Yes sir, the principle is like that..

@goodshopbest6571

2 жыл бұрын

@@manualtech6673 доброго времени суток я вас не знаю и вы меня нет но посмотрев ваш ролик вы мне не открыли ни чего нового но протолкнули меня на идею взять основу горелку и просто поставить ее в топку шланг вывести не проблема а тем более у меня печь в гараже вертикальная из газ Балона вообщем спасибо за то что пришёл к этому ( устал дровишки мелкие пилить) а для других хочу донести что это ваша проблема что вы потратили время впустую( не чего удивительного и т. п) а не человека который вас не удивил ) по сути и меня не удивил, но кто потратил время впустую а кто то даже пусть потратил своё время и при этом извлёк что-то для себя знай ты не потратил время впустую!!! Без обид уважаемые ни кого конкретно не хотел задеть даже если что у кого саовпало что-то или самнения какие-то знайте это мое личное мнение которое вас не как не может волновать а тем более задевать забейте не тратьте время зря!!!

После первого теста сараю по ходу кирдык .

@manualtech6673

2 жыл бұрын

извините, вы можете объяснить?

@nurlansha7406

2 жыл бұрын

@@manualtech6673 кирдык это значит - конец, нет сарая сгорел сарай.

@4EKU6KA

2 жыл бұрын

@@manualtech6673 это юмор такой... черный :)

@user-kq8yf3jo6t

2 жыл бұрын

Да безопасности ни какой! Пожароопасна! Взрывоопасна☠️!

I cant see what us used as fuel

@korikrali

2 жыл бұрын

Probably kerosene... or maybe alcohol

Peace and mercy of GodCan you give me the idea from the beginning, Watts and thank you

Mnrt sy ini mantap mas 😊👍👍👍, gile keren banget power jet nya 😁👍

@manualtech6673

3 жыл бұрын

okay, terimakasih agan.. sudah mampir dimari..😊😊

@handyboen

3 жыл бұрын

@@manualtech6673 hehe masama mas....yg sy bikin pake tembaga juga tapi versi mini, belajar dr youtuber jepang hehe...

@manualtech6673

3 жыл бұрын

@@handyboen asiappp... boleh minta link nya mas, yg video dr japan..😁😁😁 buat saya belajar lagi..😁😁

Itu dibawah dikasi tutup botol atau apa aja yang bisa nampung spiritus atau bensin dikit, buat pembakaran pertama manasin koil-nya. Kalau langsung dialirkan seperti itu kebanyakan dan bahaya kan.

@manualtech6673

2 жыл бұрын

siapp gan.. terimakasih saran agan..

not very helpful . what is the fuel ? how do you keep pressure ?

@manualtech6673

2 жыл бұрын

gasoline sir, when the fire starts to shrink then I will increase the air pressure in the fuel tube, pumping up to 3 or 4 pumps

Mantap bro tapi ada yg kurang dikit.. coba kasi tapungan dibawanya ntuk mancing api sikaligus biar api gak kemana2 pas ditengah

@manualtech6673

3 жыл бұрын

oke siapp mas bro, ..

Kurang aman gan terlalu pendek sambungan antara tembaga dan selang nya.selebih nya mantap gan.terus berkarya

@manualtech6673

5 жыл бұрын

oke shaapp kak..., terimakasih bnyakk pokoknya..😊😊

Bagus karya nya mas, saran, bisa di tambahin keterangan bahan apa aja yg di pake, terus beli bahan nya dimana, karena orang awam seperti saya ga tau nama2 dari bahan itu, terutama yg dibentuk jadi spiral itu 😅

@manualtech6673

5 жыл бұрын

okey, terimakasih kak.. iya untuk yg terlanjur sy buat itu, bahan2 primernya cuma selang tembaga(biasanya dipakai oleh para tukang service AC atau kulkas) 2meter(kurang panjang sedikit), selang plastik aquarium+pengatur stoper nya, itu saja kemudian hanya butuh alat2 pendukungnya saja ya kak, besok jika ada ide lagi saya buat video yg lebih jelas(keterangan bahan2nya) terimakasih banyak kak masukannya ya

@manualtech6673

5 жыл бұрын

oh iya, bahan2 bisa didapatkan ke tempat service kulkas atau ac terus slang plastiknya bisa di dapat di toko perlengkapan aquarium bisa, diapotek bisa pakai slang infus

@rahmadaditio6944

5 жыл бұрын

@@manualtech6673 siap, terimasih mas penjelasannya. Terus berinovasi mas, terus sempurnakan produknya smpai bisa layak produksi masal. Sukses terus dan tetap rendah hati 🙏🙏

@manualtech6673

5 жыл бұрын

okay okay., sama2 kak 🙂🙂🙂🙂

@lintangtimur6599

5 жыл бұрын

@@manualtech6673 selain selang infus agak kerenan dikit apa ya? Pake spt regulator (variable) tp mini gt entah apa namanya.

Ini mah kompor gerobak nasi goreng. Cm skrg dah diganti pake kompor gas.

@manualtech6673

4 жыл бұрын

😆😆😆😆😆😆😆😆 iya ya...

@AnakLanangSorkelir

4 жыл бұрын

Wkwkwkk,, bener nih hahahaha

wow, mantap ni tutorial teman. keren. asli nonton sampek pinter saya. salam kenal dan kompak selalu.

@manualtech6673

5 жыл бұрын

😁😁😁😁😁 makasih kak sudah mampir, hahah berlebihan.. salam kompak..

This higher-level of reverse evolution is the best way to solve unwanted population growth. He should teach his family and friends these amazing skills.

You don't show what and how your burning

1 liter bisa kuat brp lama kak nyala apinx?

@manualtech6673

5 жыл бұрын

itu kak, udh dibahas pada pertanyaan yg sama kak, ... silahkan baca2 Komennya oke..🙏🙏🙏🙏🙏

@doanprasmana1444

4 жыл бұрын

kecilin lubang outputnya

@iyanaldy3688

3 жыл бұрын

@@manualtech6673 bahan bakar nya pake apa ,

@manualtech6673

3 жыл бұрын

@@iyanaldy3688 pakai pertalite bang..

what is the size of copper tube and length needed thank you ang best regard

Gostei ... simples e eficiente

me encantaría que lo hicieras pero que el combustible baje por gravedad

@manualtech6673

4 жыл бұрын

buen amigo, si el material está listo más tarde, subiré el video nuevamente, gracias por venir a mi canal

@luzgol

4 жыл бұрын

@@manualtech6673 ese sistema que usas para mandarle el combustible a el sistema a presión como se llama nunca lo había visto

@manualtech6673

4 жыл бұрын

Es muy fácil, sólo tiene que insertar el combustible en el tubo (contenedores usados de bebidas usadas por ejemplo) vamos a dar presión de aire A continuación, conecte entre el tubo y el dispositivo con la manguera. Simplemente simple.. Amigos en

F 22 raptor engine

@manualtech6673

2 жыл бұрын

😁😁😁😁😁😁thank U my friend 🙏🙏