This explanation is excellent… I just purchased these two kits, and the included Mopar directions, leave a lot to be desired… Thank you!

Followed this guide to the T and had no issues doing my install. Thanks for the great video.

@TylerPotter

2 жыл бұрын

That is awesome to hear! Thanks for the view!

Very nice installation guide along with all nice tips! Loving the quality and voice as well. Thanks a lot!

@TylerPotter

3 жыл бұрын

Glad it was helpful! Thanks for the view!

@MidwinterEclipse

2 жыл бұрын

You love his voice? Are you m or f?

You make installing that kit look so easy !!!! Love it thanks and so glad I found a Mopar Kit ....You have a new Follower...all the way up in NS Canada !!!!

@TylerPotter

3 жыл бұрын

Thank you! That means a lot!

@tripleseven8361

4 ай бұрын

Greetings from New Brunswick…

Great step by step... both these kits are getting slapped on tomorrow. Thanks again for the video.

@TylerPotter

2 жыл бұрын

Nice! They are really nice and work well. Thanks for the view!

@CCT.8B

2 жыл бұрын

@@TylerPotter Followed your video... install was smooth and fast. One thing I am running into with 37s is that even though the tire is now out and up a bit more, the backup sensors are always triggered now. Any suggestions on a fix? Thanks!

@TylerPotter

2 жыл бұрын

There was supposed to be a software update for the park sensors through Mopar that was going to correct this issue with larger tires setting off the park sensors, but I have still yet to see it come out.

Be aware all, the hinge screws are T55 Torx, not T50 as mentioned in the video. I learned the hard way and just stripped 2 of my screws.

@TylerPotter

2 жыл бұрын

Weird thanks for the certification. Sometimes the paint is very thick on the bolt heads making the bit a real bear to get to seat fully.

One of the ways to get the long tire bumper fully seated is to leave the interior trim piece off during installation. You can then use a pair of pliers to grab the threaded tip of the bumper and pull it until is literally pops in and becomes fully seated. Using a little glass cleaner on the threaded tip of the large bumper does also help a little.

@TylerPotter

2 жыл бұрын

This is a great tip! They actually just changed the design on the newest long bumpers and now have a push in clip style vs. the screw in. It is soooo much nicer to work with. Thanks for the view!

Thanks for this video - definitely helpful to see this before tackling the project!

@TylerPotter

Жыл бұрын

No problem! Thanks for the view!

@ryanfry2040

Жыл бұрын

@@TylerPotter If you ever want to review a phone mount system please let me know - Bulletpoint Mounting Solutions

Have you ever had issues with the rear tailgate sensor showing its open intermittently while driving? Im having this issue after installing the reinforcement bracket

@420sack

9 ай бұрын

Any suggestions @tyler porter

@TylerPotter

9 ай бұрын

Weird we have had some rear park sensors issues with them going off but never a tailgate open message issue. I would suspect it is a latch issue?

@420sack

9 ай бұрын

@tylerpotter have you seen any fail? I notice it more on bumpy roads or while off roading. Occasionally will get the alert and go away once it notices that the door is actually closed

This video is phenomenal. Thank you for this.

@TylerPotter

2 жыл бұрын

Glad it was helpful! Thanks for the view!

Thanks for sharing, very helpful. Any tips on putting the back up camera cover on with a 35” spare tire with -6mm offset? Currently using the stock lug nuts, and seems to block the cover, do I need some low profile lug nuts. Also is it possible to just purchase the extra long rubber isolator from Mopar? Thank you!

@TylerPotter

2 жыл бұрын

There are a lot of aftermarket wheels that don't allow the cover to fit back on. We normally just leave the cover off in those cases. Thanks for the view!

I need this for my 2021 Rubicon Snazzberry !!!! Still waiting for it to be shipped to 🇨🇦 !!! Jan 17th

@TylerPotter

3 жыл бұрын

The color is AWESOME! Congrats you will love it! Thanks for the view!

@cynthiaraftus7599

3 жыл бұрын

@@TylerPotter Did you do a vid of the step bar install ??

@TylerPotter

3 жыл бұрын

@@cynthiaraftus7599 No, but next time I get a set I defiantly will!

@cynthiaraftus7599

3 жыл бұрын

@@TylerPotter Thanks Tyler Looking for the DYI so I can do my self :))) when they come, I jumped into a Rubicon yesterday and I DEF need them for when mine shows up ....LOL Me short

Such an excellent video I subscribed!

@TylerPotter

2 жыл бұрын

Thanks that means a lot! Thanks for the view!

In addition to the reinforcement kit, Did you purchase the whole spare tire carrier or were you able to purchase the bracket assembly? Not just seeing just the bracket on the Mopar site. I think the carrier that came with my Rubicon should be able to be reused.

@TylerPotter

3 жыл бұрын

Just the tailgate reinforcement and the tire carrier lift brackets, both of the part numbers should be in the description, but yes you are correct you reuse the factory tire carrier and bolt it on with the two new Mopar parts. Mopar Tailgate Reinforcement P/N 82215356AB Mopar Tire Carrier Bracket P/N 82215355

Great video but maybe you could explain how to disconnect the brake light wire. I tried to disconnect the wire for over an hour and had to give up. I’m sure it’s something incredibly simple but when you don’t know the trick you may as well be trying to climb Mt Everest.

@TylerPotter

2 жыл бұрын

There is just a small tab that you push down and then the connector should pull apart. Sometimes the tab will get stuck and you will need to use a small screw driver to pry up on the other end of the tab. Hopefully you got it and thanks for the view!

Put a bit of adhesive on the spacers to hold them in place until all the bolts are in place.

@TylerPotter

3 жыл бұрын

That's a great idea! Thanks for the view!

Awesome video install. Does anyone know if the spare tire carrier kit (82215355AC) is needed to install the XR OEM wheels which are 35 onto a Rubicon JL, or if just the tailgate reinforcement kit is enough (82215356AB)

Regarding the tailgate bracket, On the top there's a tab with a hole is that for antenna? Thanks and Thank you for your video.

@TylerPotter

Жыл бұрын

That is a really good question Mopar has never offered any other accessories that would add onto the bracket, but I would assume you could add a antenna to that location. Thanks for the view!

Isn’t bad that it is still just hanging from the same hinges?

@TylerPotter

Жыл бұрын

The hinges aren't the issue, the reinforcement ties the tire carrier into the hinges to get the weight off of the aluminum tailgate. Thanks for the view!

Question for you Tyler or anyone else.. I had the dealer install this on my 2021 JL and the backup sensors are going off, they say it's the tire causing it and claimed to not be their issue. I don't buy this expanation. I bought the jeep with added 35s and this tire rack into the deal. I think they messed up the installation somehow, maybe the tire is sticking out too much or something. Did this jeep have this issue? anyone else see this issue? Nice video.. looks fairly easy and maybe I can fix this myself.

@TylerPotter

2 жыл бұрын

It seems to be very hit-and-miss on which jeeps will get angry about the tire sticking out further, it seems like the ones with after market wheels with more backspacing or offset that stick out further will be more likely to have the issue. We have been told forever ago that there was going to be a software update to fix the park sensor issue but as of now I have yet to see the software update become available. Thanks for the view!

Great video. Thanks!

@TylerPotter

2 жыл бұрын

Glad it could help. Thanks for the view!

so medium size bumps and everything else original in box is what you used first time? im running a 13.50 wide so im hoping it fits nicely

@TylerPotter

Жыл бұрын

Yes I believe so, it really just depends on wheel backspacing and tire width. Thanks for the view!

Any idea as to where you can buy accessories to screw into those 3 holes you put the plugs in?

@TylerPotter

Жыл бұрын

That is a really good question, I don't think Mopar has anything to go in those holes but I would think someone aftermarket is making something for them? Thanks for the view!

The tire relocation bracket is showing not available with no availability date listed. Is this part still in production?

@TylerPotter

Жыл бұрын

I just checked and updated the part numbers in the video description. I believe both still show active parts. Thanks for the view!

Excellent I got 35s for my 22 JL but it rubs on the bumper, will this give me enough clearance?

@TylerPotter

Жыл бұрын

Yes the tire carrier bracket will raise the tire carrier to help clear the bumper, the reinforcement by itself won't add anymore clearance without the addition of the tire bracket if that makes since. Thanks for the view!

Great vid! How thick are spacers in the relo kit? How much does the tire carrier rise from stock position? Trying to figure out how much the spare tire carrier will rise and how much it will be pushed out from tailgate due to spacers... Also, my JLUR came with Mopar Tailgate Reinforcement so i'm just wanting to raise my spare a bit after getting 35s. Do I need to install any additional spacers since my setup has spacers already to fit spare tire carrier with tailgate reinforcement offset?

@TylerPotter

2 жыл бұрын

There are 2 kits or parts installed in this video. Since you already have the reinforcement you would just need to tire carrier bracket parts. I think I raises the tire carrier around 1.5-2in to help clear the larger tires. No you normally would not need to add any more spacers but might need to adjust the tire rubber stops accordingly, the kit comes with new longer tire bumpers. Thanks for the view!

Another great vid 👌

@TylerPotter

3 жыл бұрын

Thanks again!

I use the same kit and I have 35X12.5X18 on my JL but its rub on my bottom side of bumper its that normal and now I'm planing to change to 37X12.5X17 any suggestions will help. thank you in advance.

@TylerPotter

3 жыл бұрын

Hmm that is strange? Do you have the tailgate reinforcement and the tire carrier that moved the tire mount up higher?

Did you mention does it raise the tire carrier up a little bit because I have 37’s with a 17 inch rim and it hits my bumper

@TylerPotter

Жыл бұрын

The tire relocation bracket will lift the tire up to help clear the bumper. Thanks for the view!

this truck color way is hard

Works best when cable is thrown against the outside of the tailgate.

@TylerPotter

3 жыл бұрын

Thanks for the view!

Great Video! How do you like it so far? Just started building my Jeep JL and uploaded part one of the build to my channel. I am considering this for when I get my new wheels.

@TylerPotter

3 жыл бұрын

Nice, I'll check out the channel, and the Mopar parts are really nice with the fit and finish.

@Mrskyhook

3 жыл бұрын

@@TylerPotter nice thanks for the advice man!

Spray adhesive the spacer if you have any.

@TylerPotter

3 жыл бұрын

That would also work great! Thanks for the view!

My wheel and tire setup is 110lbs , will this reinforcement be sufficient? Also running the TeraFlex HD tire carrier that brings the wheel closer to the tailgate

@TylerPotter

3 жыл бұрын

I'm not sure if Mopar has a max weight listed or not but it can only help keep the tailgate happy with the extra weight.

I ordered a new tire set 35x12.5 on 20 inch rims ...... will I need to do this install on my 2021 rubicon?

@TylerPotter

3 жыл бұрын

Yes with the added weight it would be nice to add this, and depending on the rear bumper (plastic vs. metal) the 35in tire will hit the bumper without the carrier, Thanks for the view!

All of those bolts should have torque specs. The factory hinge to tailgate bolts are 35 foot pounds.

@TylerPotter

3 жыл бұрын

You are correct, we have installed a lot of these so we hopefully have the feel down, thanks for the view!

Just curious why you wouldn't use blue Loctite?

@TylerPotter

2 жыл бұрын

It definitely wouldn't hurt. Thanks for the view!

Is this needed to fit 33s on a JLU sport s?

@TylerPotter

Жыл бұрын

No with 33's you should be fine without it, of course it wouldn't hurt to add but I wouldn't think it would be really needed until 35's. Thanks for the view!

Do I need the reinforcement on 33" tires?

@TylerPotter

Жыл бұрын

I would bet you would be just fine with 33's without the reinforcement. Thanks for the view!

What size tire in this video?

@TylerPotter

Жыл бұрын

I believe this Jeep had 35x12.50R17. Thanks for the view!

This still puts weight on the hinges doesn’t it ? So what’s the point. ?

@TylerPotter

2 жыл бұрын

The hinges aren't the issue, there is nothing from the factory connecting the actual tire carrier bracket to the hinges so all of the tire and wheels weight is hanging off of the threaded holes in the tailgate, this ties the tire carrier into the hinges with the nice bracket so the actual tailgate isn't holding the weight anymore. Thanks for the view!

nice vedio , just wondering how big tire can the original tire carrier can handle?

@TylerPotter

3 жыл бұрын

I think you can fit a 35" tire on with the stock carrier but it just adds a lot of weight to the hinges without the reinforcement, Thanks for the view!

@gregoryjulian1333

3 жыл бұрын

@@TylerPotter how does this kit reinforce the hinges? Or, it’s not necessary and the hinges can handle the weight? Just the mount needs to be heavy duty?

@TylerPotter

3 жыл бұрын

This bracket bolts over the factory tailgate hinges to add more strength.

Out curiosity, what size rim and tire? I am looking at an 18 inch tire with a 33x12.5 R18 so I am thinking this is needed.

@TylerPotter

3 жыл бұрын

These should have been 17x9 wheels with 35in tall tires. Thanks for the view!

@jeffbehringer1262

2 жыл бұрын

Would this help even with a stock sized wheel? Seems like the stronger the better? I don’t yet own a jeep and just looking at options. Overkill? Thanks.

Nice video, thanks for posting it. I have a new rubicon that I am upgrading to 37 inch tires. Looking at tire carrier options, as I have a backup camera, will this support the 37 inch tires you think? Also, will I only need the tailgate reinforcement part? Thanks!

@TylerPotter

3 жыл бұрын

Yes the Mopar tailgate reinforcement and the tire carrier brackets will support 37's. You will need both parts unless you ordered the Jeep with the factory installed tailgate reinforcement, then you would only need the tire carrier brackets. Thanks for the view!

@waburkhead

3 жыл бұрын

@@TylerPotter Thanks!

@KingFish747

2 жыл бұрын

@@TylerPotter will the 3rd brake light be visible with 37's using these parts?

@TylerPotter

2 жыл бұрын

@@KingFish747 yes there is a way you can move the 3rd brake light up 1 set of screw holes on the carrier to work with 37's. I don't have a video on doing that though

Has this kit affected your back up sensors??

@TylerPotter

2 жыл бұрын

Yes, Jeep was supposed to come out with a software update to fix the rear park sensors with the larger tire but it hasn't came out yet. Thanks for the view!

What was the backspacing on your wheels?

@TylerPotter

2 жыл бұрын

They are Black Rhino Warlord wheels, they were 17's but I really don't remember if they were 17x8 or 17x9 so looking at the website I'm not sure what spec they were for sure, so I don't want to tell you wrong. Thanks for the view!

Nice video...but please try not to talk during your impact drilling...😜

@TylerPotter

Жыл бұрын

That would help lol Thanks for the view!

Will this tire relocation bracket fix the beeping back up sensors due to the install of a 35" tire?

@TylerPotter

3 жыл бұрын

It should move it up slightly higher but depending on you wheel backspacing we have still had some of the park sensors beep at the tires, supposedly there will eventually be a software update to address this. Thanks for the view!

@T0DDS

3 жыл бұрын

@@TylerPotter so I did some research and I did 2 things. I bought a spare tire relocation bracket that moved my spare tire up 2.25”. I also ensured that the tpms semsor on the spare was as close to the 12 o’clock position as possible. I read that the tpms can cause the sensors to beep if it’s mounted on the lower side of the tire. I do not have any back up sensor issues anymore. My offset is +12. You make great videos, thank you.

@TylerPotter

2 жыл бұрын

Just looked back and read your reply, I didn't know about the possible tire pressure sensor interference issue but that totally makes since! Thanks for the info!

@T0DDS

2 жыл бұрын

@@TylerPotter Thank you for your great videos you do. Your 2" Mopar lift install videos were pivotal in my successful install. You saved me a bunch of $$ by showing me how to do it myself. You rock!

@TylerPotter

2 жыл бұрын

@@T0DDS That is awesome to hear and now you know so much more about your Jeep for future repairs and upgrades!

Will this hold a 37"🤔

@TylerPotter

2 жыл бұрын

Yes it works great with a 37. Thanks for the view!

can i fit a 38x15.50r18 tire on that tire carrier ?

@TylerPotter

2 жыл бұрын

That is a good question! The largest we have installed at the shop with the factory bumper still in place is a 37. You may need to search online to see if anyone else has had a 38 on it. Thanks for the view!

@AlexCastro1

2 жыл бұрын

@@TylerPotter would a 15.50 width tire be a problem for that tire carrier or do i need something else?

What wheels were those?

@TylerPotter

3 жыл бұрын

They were Black Rhino brand wheels.

Great video man! I just uploaded a video of my Jeep Wrangler with new wheels/tires and a 2.5 lift....go check it out!!

@TylerPotter

Жыл бұрын

Thanks man!

Seems like a gimmick.

@TylerPotter

3 жыл бұрын

It just to help with the weight of the larger spare wheel and tire and to locate it up to clear the bumper, thanks for the view!