Thanks very much for this video. I’ll get on mine tomorrow.

Jake you deserve to get an easy fix once in awhile. Hope the rest of your day went that easy. Have a good one. 👍

You make it look easy 👍

RIGHT ON ! SOMETIMES IT IS THAT EASY .THESE ARE THE ONES YOU REALLY ENJOY

logical approach and knowledge of a system applied there . i have been watching your channel to long when i saw that scan data i was like oooo look at the stuff offline 🤣🤣🤣🤣

It really just goes to show how important grounds being clean and tight are. Good find. Great video 👍🏻

Nothing like a good visual inspection 🎉

Its easy when you have to correct knowledge. Thanks for sharing as always your videos help a lot!

This isn't easy for others but for you it was easy because you work smart. Very nice procedure

Thanks ! Valuable information and wonderfully taught ! Thanks mate . 👊🏼🔥

Great video Jake.

Love these detailed videos 👍🏻👊🏻

Great way to start the day.

Awesome work! I just dealt with my first RF Hub last week on a 2019 Ram 1500. Took me a few hours to figure it out. Had to ask for more time since the seats needes to be removed to access the hub. RF Hub had corrosion in it!

Well done 👍

Good find amigo

Some of them you can hold the button to get them to crank. Neighbor to my shop had a push start kia. His battery was dead and it didnt start. He borrowed the battery charger and came down after and said it still wouldnt start. Took me about an hour to figure it all out being I never seen that before. When he tried to start it the first time it used all the vacuum in the booster. So once he charged the battery the hard brake pedal was not allowing the brake pedal to travel enough to trigger the switch

Easy for you! I would have changed the Engine Gearbox the Chassis then finally scrape the paint off the bodywork. You nailed it.😃👍

Great strategy, Jake! it almost looked too easy 🙂 I was expecting some sort of intermittent connection - finding it is always the problem 🙂 Quick interesting video!

Good video and diagnosis! Wondering what else was left loose or missing from whatever work was done back there.

Nice video and great find. Usually the loose nut sits behind the wheel in a Jeep. This looks like an auction car and or repo. Someone might have sabotaged the car. I hauled a lot of repos out of Alaska to Washington and you wouldn’t believe what people do to cars.

@autodiagyt

5 ай бұрын

It was recently bought from auction yes

Never thought to load a fuse when I test them.. that’s really good. I would’ve liked to have seen that in your last video with that fuse issue.

@autodiagyt

5 ай бұрын

The one on TikTok?

Car must have been built on a Friday after lunch….

@mdushaka6403

5 ай бұрын

😂😂True, l was there

@JamesLee-oe7mt

5 ай бұрын

By Boeing

@bbeauregard4181

5 ай бұрын

Wet lunch!

@mattw1393

5 ай бұрын

I think there’s a few lines about jeeps in general there but I’ll choose my audience and let them slide. 😜

Grasias

Bro, we would love to see the POST SCAN RESULTS, there were many modules not working, many codes that seemed related. I agree that the Start Button was a great starting point with no COMM from the RFH but as for me, I like to see the same test that led us to the repair reran at the end, I also want to be sure of the Module count on each vehicle if the Tech will also help us out with that info, cheers, love all your videos and would appreciate the little extra info.

Good eye

🤣🤣🤣 that was quick. 👊

Hope u can get the link for test light it's cool tester

@autodiagyt

5 ай бұрын

Yeah I’ll add it to the Amazon when I get time and actually remember lol. There is some other things I need to add as well

Unless I come across something better, it's either THAT TopDon, or an x431 proS, that I'm going to get, this Spring.... Incredible tools!

@overload3996

5 ай бұрын

Topdon doesn't have autoathu for dodge, x431 has it.

The one thing I regret not having on my Autel is topology. Regarding that nut, it might be wise to use a lock washer or maybe locktite, it looks like it might have spun itself off with vibration....

@autodiagyt

5 ай бұрын

Someone had to of taken it off because it was started back cross threads

Wow, it was either a test for you, or a Monday morning or Friday afternoon build...

takem when you can getem, nice get the easy ones

It's nice not to hv one totally messed up right Jake

Loadpro did same thing

First thing I thought was tipm

👍👍

It it ironic that if you tested the power and ground on the RFA connector with a Power Probe or that probe that they gave you, the ground would have tested good, even though it's weak and barely hanging on. You need a strong incandescent test light that puts a good load on the circuit, to stress test the ground. That new probe would have tested the ground as bad if you had used the load function. Lessons learned.

Good video. Where did you get the test light from ??

@autodiagyt

5 ай бұрын

Amazon

@saiautomotivemilton.7128

5 ай бұрын

Thank you

I could see that turning into a giant rabbit hole for most. Not Jake tho! Not even a challenge!!

Growing up I always went to my uncle’s body shop and one day he had a new Cadillac there he said the dealer sent it to him to find a noise we went for a ride and every time we tuned you heard a tapping in the back so we pulled out the seat and went again this time I climbed in the back to listen and look I found the noise it was a washer and a nut tied on fishing line a note was Rolex and taped on the line it said I hope it costs you a fortune to find this

@autodiagyt

5 ай бұрын

That’s crazy lol

I would have replaced the starter then the ECM BCM FUSE BOX and then called a wrecker truck to take it to you 😅

👍👍😊😊

4:15 Probably 800 mA load!? Because there i saw some wire resistor.

They must have been having problems all along, or someone was back there and did some shoddy work

I wouldn't say "sometimes it's that easy". I big portion of how easy it looked has to do with your experience. Just looking at topology you were able to narrow down an hours worth of time. Just pointing out how much experience plays into being efficient at diagnostics. As well as knowledge. Which in part cones from experience.

hello I have a Jeep Grand Cherokee limited 2016 . my stop/start system today just stop 5min from home . stick where it say D N etc so the D was blinking its took about 3mins for the car to start again then when it did it was like rumbling for few seconds then i pulled over the car the stop/start come on screen but it was yellow with an ! . do I need to take to a shop or could I fix myself ? and what do u think the problem maybe? help please and thanks

@autodiagyt

3 ай бұрын

I would definitely recommend taking it to a quality shop to have it diagnosed. Several things could cause those symptoms.

Would it be in the same location on the 2020 Jeep Grand Cherokee 3.6l 4x4

@autodiagyt

2 ай бұрын

I have no idea. I would need to look at service information.

@arielcastro34

2 ай бұрын

Pls help me I would hate to change the starter which is a pain to replace I don't have that expensive tool

@arielcastro34

2 ай бұрын

It has to be topology scanner to read the codes cause my it doesn't allows me 500 Launch scanner

@autodiagyt

2 ай бұрын

@@arielcastro34 I would suggest taking it to a professional that has the tools and knowledge to diagnose your concern.

Where part of the car did he went lastly

@autodiagyt

Ай бұрын

For the RF Hub?

Somebody should tell Stellantis about this thing called nyloc nut fasteners--or maybe locktite--or chewing gum?

Yup! The wonderful world of electronics. Better to have a key going into an ignition switch than this push button lunacy!

Hi. Im one of your followers from Ethiopia. Im a mechanic and couldnt get any data on most cars but there is one issue on a 2006 Yaris( i3 1kr engine with cvt). The car starts good and sounds good but has almost no power at low rpm. I checked almost everything but couldnt find the issue. But one thing i found odd was the ignition advance becomes negative when trying to move uphill from stopped state. If the car start moving power comes back. Chhecked for knock sensor, ECU, Transmission, Fuel system, vacuum... . i tried everything but I couldnt identify the cause of retarded timing. Please help

@autodiagyt

5 ай бұрын

The most common thing to retard ignition timing is Knock so see if you have a data pid from the knock sensors

@mamababa8873

5 ай бұрын

@@autodiagyt what should i expect looking at the live data?