Would have been interesting to know what failed on that control board.

@proexservis

10 ай бұрын

Interesting yes, but not worth it my time when PCB price of this model is 10€ 👌

Здравствуйте.Подскажите пожалуйста,где можно приобрести такую плату

@proexservis

5 ай бұрын

Hello, at any electrolux service or at their official site, look for 2193995707 - в любом сервисе электролюкс или на официальном сайте ищите 2103995707

Another question would be, can you bypass the control board and just run it at full speed all the time?

@proexservis

10 ай бұрын

Older model of this model had no PCB for regulation, just power switch. So motor is designed to handle it, but that circuit board cost 10€ and it protect from overvoltage that 50€ motor, so it is better to have that PCB there

@curiosity2314

10 ай бұрын

@@proexservis Thanks for the reply's. The reason I had asked about the circuit board was that I have an inexpensive Bissell zing lightweight with a board and a possible issue with the transistor that has a decent sized heat sink on it. Solid cap, resistor and a diode, off of that it has the sliding variable resistor for for speed. Does have a fuse that tested good and what I found interesting testing the power cable and wind back unit which tested good but they are switching the neutral side which seems odd? With that the switch tested good. I did not put the full 120v direct yet to test the motor as I was not sure if it would handle it without the board. I will try that tonight. One day it worked and the next it did not without stress on the unit and it always is unplugged unless it is used. I will try the motor tonight. The whole vacuum costs 59$ delivered. I did buy one but figured I would see if I can have a second on hand. Thanks again.

@curiosity2314

10 ай бұрын

@@proexservis Well tonight I bypassed the control board and a big zero. Pulled the motor and tested one lead to the cosponsoring brush and I did have continuity, tested the other and a zero; looked closer and the wire from the winding was broken from the terminal. The wire is protected by some fiberglass material that I will have to strip back and being a 4mm gap I will have to bridge it somehow and test. If you have a good way to do this let me know otherwise I will do my best. Thought the update might be help for some out there. Looks like a quality brushed motor with lots of life left. Something to be said about brushed motors, they last allot longer then most imagine.

@proexservis

10 ай бұрын

@@curiosity2314 I don't have one. But good luck with it, i think you have more work with it than the whole vacuum cleaner cost. Yes, some carbonbrush motors last a long time, but some have 2-3 years and are completely trashed.

@curiosity2314

10 ай бұрын

@@proexservis That transistor looking thing was a BTA16-600B Medium Current Triac,Gate Trigger 16A, 600V,TO-220, looked it up and tested it and it did test good. There was a TVS diode you had to jump through all kinds of hoops to test and at this point I'm sure it is fine, the rest was simple to test. I will send the results once I have them. I was surprised that the brushes were replaceable, what would trash the motor? For me it's about making something that does not work, work. As a business it would be a no brainer to trash something that could be repaired. Units like this might be better given to charity organizations that refurbish? Update coming soon. 😀

It turns on and off on the handle must be a man taking it all apart to see what's wrong.

@proexservis

27 күн бұрын

Hi, try to reset and set pcb again 🤔 Same board: kzread.info/dash/bejne/p5yjudhvZr2_YLg.htmlsi=Fp5m2dBV2i9bpENK

Здравствуйте.Подскажите пожалуйста,где можно приобрести такую плату

@proexservis

5 ай бұрын

Hello, at any electrolux service or at their official site, look for 2193995707 в любом сервисе электролюкс или на официальном сайте ищите 2103995707