iPhone 8 Plus (No Service) No IMEI When Dial *#06# Repair
Ғылым және технология
Hello Everyone.
in today's video we have an iPhone 8 plus came for no service after they change the housing of the phone, as you can see in the video someone already tried to change or reball FL2002_EF which is a filter for the antenna for better network but still no chance because we have a problem with baseband.
now before you go and begin with the baseband try to see the history of the phone its not an iPhone 6 so you can just reball the baseband and you good to go, no you have to check everything before you go directly to the baseband, did my diagnostics and turns out the there is a problem with WTR which is the transceiver luckily there is only one WTR in this qualcomm so we replace the ic and the network function comes back to life again.
0:00 Intro
1:30 Board under the microscope
2:40 Testing and Making diagnostics
3:52 Start to remove the WTR
4:43 Reballing a new WTR
5:08 Soldering the new IC
5:30 Testing Everything (2G-3G-LTE) and calling
Now All The Links Has Been Updated To Aliexpress Links Except Microscope Stuff And All The Links Are Working Fine
(BUT YOU HAVE TO SKIP THE AD TO ENTER THE LINK ANY LINK DOSENT WORK PLAESE MAKE SURE TO MENTION IT IN THE COMMENTS DOWN BELOW)
Quick 861DW Hot Air Station: ishortn.ink/XJvdBKX2i
Hakko FX-951 Soldering Station: ishortn.ink/KtX3Wl0S9
Desoldering Wick Braid: ishortn.ink/JtUlnxvqM
Solder flux: ishortn.ink/YD18IvRKe
Phone PCB Circuit Board Holder: ishortn.ink/Lihx9N5EH
Curable Solder Mask Repairing Paint Green: ishortn.ink/LBn7pY41D
Best Stencil for all iPhones: ishortn.ink/kcY1p0IKO
Wire-type soldering iron tip cleaner: ishortn.ink/08Zdtf8AI
Solder Paste: ishortn.ink/AVh9ekcCu
Low-Temperature Solder Paste: ishortn.ink/kXexte5pi
CHIP JUMP WIRE: ishortn.ink/emd06HILE
*NOTE: YOU CAN OPEN THE UPPER EAR SPEAKER OF ANY IPHONE AND TAKE AND TAKE THE ORANGE COIL FROM IT AND USE IT AS A CHIP WIRE JUMPER
DURABLE USB UV LAMP: ishortn.ink/yzZ1D6eR9
SOLDER WIRE: ishortn.ink/lrex5VTcr
Barrier Pure Copper Heatsink Shim: ishortn.ink/y5bBOW4Ay
LED Ring Light Illuminator for Stereo Microscope & Camera: ishortn.ink/RTyoiBNVO
My Microscope: ishortn.ink/0SY8WjC3M
Polytetrafluoroethylene Tape: ishortn.ink/ohXlQouzw
MINI PORTABLE IC CHIP GRINDING: ishortn.ink/PNbBIGIUm
My Reddit : / antoinejk10
Follow Me On instagram : / ajkb10
Join our Group On telegram : t.me/antoinekiriaky
t.me/microsolderingrepair
Join Our Groups On Facebook : / msdrteam
Thanks for watching and as always i hope you enjoyed the video and it was helpful for you if you have any questions please leave it in the comments down below and for more interesting Fixes and Future videos please leave a like and subscribe to the channel.
AJK;)
#noservice #iphone8 #microsoldering
Пікірлер: 37
Nice work🔥🔥🔥🔥🔥
Subscribed.Thanks for.the upload.
Thanks Antoine
Good job
Nice work. This is exactly how we teach this repair. Did you reball the IC because you wanted some leaded balls?
@AntoineKiriaky10
3 жыл бұрын
Leaded balls ?? I changed the ic and I recalled the new ic because I don’t trust the previous soldering paste
Гарна англійська, Антоне)
Good job boss 💯👍🏽
I have this issue, so I had an accident with my 8+ then I lost signal and imei won't display. However I don't have the equipment to do the reballing of the IC. I'm guessing the chip isn't connecting properly to the board terminals. Can I heat up the chip with a heat gun, to reball it without removing it? Kindly lemme know if this is possible.
Can’t replace a new baseband? Or it must use a original baseband?
In my iPhone x no service and software update option not show
Music is sooooo good what's the music name?
Hello mister, may I ask you what the reflow gun temperature was set to? I have the same issue with my iPhone 8 Plus and I just want to reflow the chip without removing it. Thank you for this video.
@AntoineKiriaky10
5 ай бұрын
If the chip is under filled, then it’s best to remove the chip and Reball, the under fill could be pop and make the chip higher than the pad on the board, causing bad connection and greyed pads, but you can use 310-320c 40-55air
@oneundecided
5 ай бұрын
@@AntoineKiriaky10 Thank you!
which flex using
Yes
Я думал, это проблема только у семерок. Такое у всех - 7, 8 и SE 2020?
Hello sir, i hope you can help me. Tried all of the possible troubleshooting and still doesn’t work. I kind of happen to have opened my iP8+ multiple times and changed battery, charging port set, taptic engine. I kinda of ruin and rip off a flex around upper middle right portion of the phone. I’m not sure if replacing that will resolve it. Also, not sure what’s it called that’s why I can’t buy on online yet.
@AntoineKiriaky10
2 жыл бұрын
DM me
What if the ieim does come up
Only in few minutes repair the baseband of iphone 8plus ? Because i confuse . Coz other tech said need to leave my phone atleast 1day for repairing baseband . Please explain sir if it is okay to leave my phone 1day ..thankyou sir !
@AntoineKiriaky10
2 жыл бұрын
Yeah I guess, I mean it depends on the repair shop as you can see in the video there is a lot of speed forwarding so obviously I didn’t make in couple of minutes
Same problem
Привет, есть софт который меняет восстанавливает имей?
Please help meialso have this.
Do you repair phones I have iphone 8 repaired
Why baseband issue only repairs in just youtube videos this is very serious issue its can’t repaired
@AntoineKiriaky10
2 күн бұрын
DM me if you need actual repair
How much it takes for such repair ? I am having same prob with my iphone 8 and i am not getting anyone here in India to repair this issue
@AntoineKiriaky10
2 жыл бұрын
DM me
@MrAndy814
2 жыл бұрын
Done
Kharcha kitna aayega
After *#06# dial not show
@anisoqueen3935
2 жыл бұрын
Me too 😢