Introduction to solidworks flow simulation : cfd analysis of convergent divergent nozzle
Learn how to carry out cfd simulations using solidworks flow simulation module for convergent divergent nozzle.
Жүктеу.....
Пікірлер: 22
@germangarrido88422 жыл бұрын
That´s an interesting video. Thank you!
@cad4fea
2 жыл бұрын
Glad you liked it!
@corneesmit72053 жыл бұрын
But how do you simulate what happends when it exits the nozzle
@esquivel13 жыл бұрын
The "inner wall" boundary condition suddenly appears @5:59 (around the 6 minute mark). How was this set? Also, How can I view the exiting air? I had a look at the previous comments/answers and I do not understand how to check the "analysis settings" or in better words, what settings to change. Please help :)
@impactodelsurenterprise2440
2 жыл бұрын
Yeah he didn't show how to set the real walls. You have to select the inner cone surface, leave out the inlet and exit boundary. Then, edit your Cut Plot, under the Contours, there is a small button to the right of "Pressure", click that and reset the plot max and min value
@makkihassan91183 жыл бұрын
how to use solidworks flow simulation results as initial boundary conditions to perform anoth flow simulation based upon the results
@lexasolopow Жыл бұрын
Thank you very much
@jiml8120 Жыл бұрын
what is inlet to throat area ratio and exit to throat area ratio of this ?
@eloymartin89703 жыл бұрын
Same problem: ((( my simulation is in "preparing model" and never ends - why does that happen? thanks!
@cad4fea
3 жыл бұрын
check analysis settings
@eloymartin8970
3 жыл бұрын
@@cad4fea WOw, Thanks! -___-
@MsMatheusrichard2 жыл бұрын
250 bar?
@user-vo8ou1gf3k3 жыл бұрын
🥰🥰🥰🥰
@reviewvideoes5006 Жыл бұрын
when i make the geomatry and opens it in flow simulation the error appears that please make a lid
@cad4fea
Жыл бұрын
Ok, then please make lid manually in part model before ging to flow simulatin mdule.
@hilmonstiglet41573 жыл бұрын
Cool
@MsMatheusrichard2 жыл бұрын
Hydraulic system is about 80 bar, 250 bar is so much!
Пікірлер: 22
That´s an interesting video. Thank you!
@cad4fea
2 жыл бұрын
Glad you liked it!
But how do you simulate what happends when it exits the nozzle
The "inner wall" boundary condition suddenly appears @5:59 (around the 6 minute mark). How was this set? Also, How can I view the exiting air? I had a look at the previous comments/answers and I do not understand how to check the "analysis settings" or in better words, what settings to change. Please help :)
@impactodelsurenterprise2440
2 жыл бұрын
Yeah he didn't show how to set the real walls. You have to select the inner cone surface, leave out the inlet and exit boundary. Then, edit your Cut Plot, under the Contours, there is a small button to the right of "Pressure", click that and reset the plot max and min value
how to use solidworks flow simulation results as initial boundary conditions to perform anoth flow simulation based upon the results
Thank you very much
what is inlet to throat area ratio and exit to throat area ratio of this ?
Same problem: ((( my simulation is in "preparing model" and never ends - why does that happen? thanks!
@cad4fea
3 жыл бұрын
check analysis settings
@eloymartin8970
3 жыл бұрын
@@cad4fea WOw, Thanks! -___-
250 bar?
🥰🥰🥰🥰
when i make the geomatry and opens it in flow simulation the error appears that please make a lid
@cad4fea
Жыл бұрын
Ok, then please make lid manually in part model before ging to flow simulatin mdule.
Cool
Hydraulic system is about 80 bar, 250 bar is so much!
Hello sirs Pleased to be making the needful
@cad4fea
2 жыл бұрын
Thanks for visiting ansol
@cad4fea
2 жыл бұрын
Thanks
Fluids simulation with solidworks has no sense