Thank you the only way to keep this hobby alive is bringing in newbies. And making it easy for them to stay.

@RCVideoReviews

Жыл бұрын

Couldn't agree more!

@Top-Jimmy

Жыл бұрын

Absolutely, Ive been using analogue for years and its hard to find any ELRS beginners guide anywhere. If there are any, I cant understand the jargon and they are normally rushed. This video is very helpful mate for sure.

@RCVideoReviews

Жыл бұрын

@@Top-Jimmy Glad to help. Thanks.

@caturlifelive

11 ай бұрын

@@RCVideoReviews thank you 🙏🏻

Thank you for this video. I just got the ELRS module yesterday, so I'm the newest of newbs!

@RCVideoReviews

Жыл бұрын

Hope the video helps. Have fun with your new tech.

So true about long range...video will go long before control signals. Furthermore, 2 watts would provide little increase above 1, as there is not a linear relationship between power and signal strength. Thanks so much for this video, I've been kind of resisting elrs a bit because I haven't had any range problems, however, it's getting harder and harder to buy certain quads that aren't ELRS.

Great video. I have a Matek 405 flight controller with elrs built in and was struggling with connection. Your comment about the Matek target being DIY made me go back and actually read the manual. After updating the firmware, it works great! Thanks for all you do, especially for us noobs to elrs.

@RCVideoReviews

Жыл бұрын

Glad it helped and you're welcome.

Just getting into ELRS and bought everything you use here (easiest for following) and everything worked and connected great!!! Using it all on planes so I picked up the mateksys CRSF-PWM-V10 to go with my receivers. Got the radio and receiver working thanks to you, now to figure out the rest!

@RCVideoReviews

Жыл бұрын

Great to hear! Good luck. Have fun learning ELRS. It's a really nice RF system.

This really helps, just getting started.

13:21 Was idly listening from my office desk in my sign shop as an RC Newbie looking to outfit my FMS Fox 3000. Your first couple of lines was spot on! People in most help videos are speaking english but the nature of the craft has so many abbreviations, all a newbie can hope for is knowledge obtained by osmosis. FPV, ELRS, BNF, PWM, FJB, the list is endless. When I discovered people fly long range on auto pilot and use FPV I was thrilled. My heart started pounding as I was alerted to the reality that me, a professional power Mac user can join in the fun without using a windows platform, which is harder to me than flying without AS3X and Safe. ExpressLRS-Configurator-1.5.5.dmg had me from hello! Currently, I'm all Spektrum but I will be buying all my gear through your links because your video made my day!

Great content I just love it! This RC hobby will never grow old! It is so exciting! Your videos are so helpful

@RCVideoReviews

7 ай бұрын

Why thank you. I'm happy to know you find my videos helpful :) And I agree, always something around the corner in RC.

@reginaldmcnab3265

7 ай бұрын

@@RCVideoReviews I’ve been hearing about ELRS and all I know about it is that it is a long range radio control system for drones and since I only fly heli I never look into to it But after watching your video! Now I am curious

@RCVideoReviews

7 ай бұрын

It's definitely not constrained to long range. Initially that's where they started as those folks are RF enthusiasts; but the LOS capabilities have grown significantly this year and right now I use ELRS on all of my fixed wing LOS planes.

@reginaldmcnab3265

7 ай бұрын

@@RCVideoReviews oh ok! So just for flying helicopter, I can use express LRS?

Thanks for this. I have recently made the switch to ELRS, starting with the RadioMaster Ranger transmitter module, RadioMaster RP3 receiver, & the first of all five of my helicopters to get it is my Goblin RAW 420. Eventually I will put all of my helicopters onto ExpressLRS. I have been following their development since 2019, back when I first bought my RadioMaster TX16S Max Edition controller. Nearly four years later, & _this_ has come out & the ELRS devs have finally added support for helicopters is amazing. =^/.^=

@RCVideoReviews

Жыл бұрын

You're very welcome. Glad you found the video useful.

Perfect timing! Just about to use my first non-dji fpv system which is elrs

@RCVideoReviews

Жыл бұрын

Perfect!

Really good full with informations and very educational in hobby all about expres elrs ... and radio understanding 😉

@RCVideoReviews

Жыл бұрын

Glad you enjoyed it!

Thank you ...from a complete nooby-newb just starting into this stuff.

@RCVideoReviews

11 ай бұрын

You're very welcome.

Universal criticism of RC You tubers is totally ignoring the novice new user. no one explanes what elrs is is and is it right for you today as a novice and what do you need in the future

what a nice work well prepared and well explained - Thanks ...

@RCVideoReviews

4 ай бұрын

You are most welcome

Brilliant intro….. thanks for making the video😁

@RCVideoReviews

2 ай бұрын

No problem 👍

Great video just what I needed.👍

@RCVideoReviews

Жыл бұрын

Awesome, glad to help!

You explain things very well!

@RCVideoReviews

5 ай бұрын

Thank you!

@captjohnny

5 ай бұрын

How can I get a hold of you by email. I've got some questions.

@RCVideoReviews

5 ай бұрын

I don't really do 1:1 support via email. Your best bet is to join the discord. Invite link is in description of every video I post.

Great video !!! I flash thru INAV on all my planes with matek controllers

@RCVideoReviews

Жыл бұрын

Thanks for watching and the comment.

Thank you so much. Wonderfull job.

@RCVideoReviews

Жыл бұрын

You're welcome. Thanks for watching.

Answered all my questions to get this working on my tx16s/micro. Thanks! BTW 3.2 is available. Now to flash a ER5A:)

@RCVideoReviews

Жыл бұрын

Glad to help.

@scottiopizza7565

Жыл бұрын

@@RCVideoReviews I do have a question. Is there a way to delete or unbind a receiver that I no longer wish to use as I move forward with ELRS?

Excellent job presenting ELRS and its idiosyncrasies. Unfortunately, you've definitely talked me out of ELRS. Last flown rc planes 15yrs ago. Will start flying again as soon as I can print my Pitts. I think I'll start with Flysky IA6X then move on from there. Thanks again.

@RCVideoReviews

Жыл бұрын

You're welcome. It's definitely not for everyone and there are simpler options to be sure. What I like so much about ELRS is I can use it in everything: CRSF talks to flight controllers so Betaflight on quads, iNav on FPV fixed wing. It talks to the FBL I like to use so I can use it on helis. And it has PWM output options with telemetry, so I can use it on fixed wing for LOS. On top of that the receivers are fairly cheap.

Looking forward to watching the video when my replacement module comes in (the box had 2 barcodes - one said micro, the other said nano. Unfortunately the nano was in the box and I ordered/ need the micro)

@RCVideoReviews

Жыл бұрын

Oh no...

I love what ExpressLRS is doing

@RCVideoReviews

Жыл бұрын

Me too. It is now my main RF tech in my planes. I'm switching them all over now.

THANK YOU, FINALLY!!! - Been looking for an ELRS newb vid, Time to abort analogue, for me anyway. 👍

@RCVideoReviews

Жыл бұрын

You're very welcome.

Thanks for the video my man but I would never ever go that route and im now in love with my fry and flysky 😂

@RCVideoReviews

Жыл бұрын

Good to have options.

I understood this. I've watched Bardwell's version several times and didnt understand much, but this was awesome?

Wao great video like always thank u.

@RCVideoReviews

Жыл бұрын

Thank you.

I love those widgets you’re using on the toolbar. Do you have a video showing how to get and set those up?

Well done you... So many u/tube channels involved in the hobby assume most people who watch are proficient in the basics... Some are of course... but many are not... Thank you for going against the grain.

@RCVideoReviews

Жыл бұрын

I watch the comments and sometimes see things that make me stop and realize some people just don't have the same information. Anyway, I'm glad you found the information helpful.

I got a Ranger Micro on the way .. and later the new PCB replacement. So now i only need a Rx to test with - looking forward for Rx's with more than 6 channels.

@RCVideoReviews

Жыл бұрын

That converter I showed gets you 10 channels of PWM. $10

I wish this had popped up earlier but thanx nonetheless. Gotta get me a dongle.

I'm glad this is 2 months old rn bc I like betaflight and all, will tune the crap out of my fc if the frames good. Blackboxing is fascinating to me fr. But elrs I've been very hesitant about for no reason. Xm plus ain't too bad to me, I just don't want to ziptie antennas or keep breaking the holder tubes. And I do want to go a lil far sometimes.

@RCVideoReviews

Жыл бұрын

ELRS is maturing nicely.

Small correction, the full sized ranger can go all the way up to 2W! It is more powerful (but it's useless for most people)

@RCVideoReviews

4 ай бұрын

Not out of the box and I don't show it because I don't want to be the one responsible for telling everybody how to violate part 15 rules. So it's not a correction. The device allows it, but the manufacturer correctly set it to 1w to comply with the law.

@FAB1150

4 ай бұрын

​​@@RCVideoReviewsoh I completely agree on you not showing how to circumvent the law, but it's a selling feature even if they never explicitly say it to not get their product banned. In their website they only say "default 100mW" under RF power output in the product specs of all three for the same reason, lol If it was intentional though I also agree it's not a correction

@RCVideoReviews

4 ай бұрын

I've been flying LOS with ELRS for a while now and it's pretty rare to see Tpwr in the logs > 10mw. Every now and then a 50mw burst. 2w is just over the top and really not necessary unless you're doing some seriously long range and then you're going to have trackers, and some serious knowledge on video setups. So I figure at that point, you already know the hack. YT is a great teacher. Sometimes it's just better to leave certain things unsaid.

Nice!

@RCVideoReviews

Жыл бұрын

Thanks!

"Take your medicine, go spend the 7$. It's worth it" LOL I had to stop the video and laugh. 0k back to it now. 32:03 min. I love the way you explain things, the telephone analogy is great we used that when I worked in telecom to explain why we were twisting two wires on our cables. OMG the pointer cam out!!!!! I am going through your channel videos, it like eating an elephant. I thought you were going pretty fast then I realized I had the speed a 1.5... I used to code a bit back in the 1980s, compiling from a tape could take hours on a big VAX, prior to that you would insert punch cards all night on like a P-11 (before my time). Talk about your "this could take a long time guys" comment! LOL You have a nice pic of the Ranger micro on your elrs lite and I hope that IK will get that when I upgrade the firmware on the TX16, I just received it and it has edgetx v.2.7.1, 2022-07 Thanks!

@RCVideoReviews

11 ай бұрын

Welcome to the channel and have fun going through the material :)

@Coyotehello

11 ай бұрын

@@RCVideoReviews BTW, I did buy "it". I kinda had too after your comment... 🙂

Great video Do you have to cross off UART invertet when you have a TX16S mkII ?

@RCVideoReviews

Ай бұрын

Not for ELRS.

Thanks 🙏

@RCVideoReviews

6 ай бұрын

You’re welcome 😊

God how do people fly with all that . Takes the fun out of the hobby it should come ready to go

@RCVideoReviews

2 ай бұрын

For beginners there are plenty of RTF options. Once you start to advance in the hobby, you'll realize there are other interesting technologies to explore. It's one of the thing that keeps the hobby interesting--learning new things. If that's not for you, then maybe just a basic RTF setup would be sufficient.

Thanks for the video! Can you make a video on how to use 8, 12 and 16CH on ELRS receivers with Pixhawk Orange cube and TX16S Mark II ELRS TX for Hexacopter?

@RCVideoReviews

Жыл бұрын

That's a little too specific for a video for this channel. Sorry. Hope this one helped though.

Great video! Thanks a lot. I hear from others that when you use 1 watt or higher power you should always use an external power supply. Is that right?

@RCVideoReviews

Жыл бұрын

I cannot validate the question. Two points: 1) We're talking about radiated power, not electrical power. I don't believe it's a 1:1 correlation between radiated power and electrical power, but if it were 1:1 then: 2) 1000 milliwatts = 1 watt. W/V=A. So 1w/5v= 0.2a or WORSE: 2000milliwatts = 2 watts. 2w/5v = 0.4a I seriously doubt the pins in the JR bay would struggle *at all* with .4a. And I know the batteries in the Tx should be able to easily handle an incremental half amp. So personally--I doubt an external pack would be required. Finally, Radiomaster did not stipulate in their instructions that an external pack is necessary for 1w of transmit power.

For anyone shopping for a Ranger module, the biggest one, with the aluminum casing, will shed heat more quickly than the smaller version, that has a plastic casing. Just something to take note of.

@RCVideoReviews

Жыл бұрын

I was flying all weekend in Florida. It was 95 degrees outside yesterday. Telemetry on the micro showed RQLY about 95% or higher, TPWR at 25mw 99% of the time with one or two spikes to 50mw. So I had superb LOS radio performance throughout the weekend with a legitimate heat test on the micro. That said, my TPWR was low the whole time. If your use case mandates a higher TPWR, the aluminum case might make sense.

@Inertia888

Жыл бұрын

@@RCVideoReviews thank you so much for all these stats, I will put them in my folder, until I have a better idea on the full range and performance of these modules. I am interested in how the 2Watts will handle penetration ( I see you suggest that LoRa is not necessarily aimed at pen, but looking forward to field-testing ) of green leaf canopy. I have not yet put my drone in the air, since I received the module.

@Inertia888

2 ай бұрын

Just an update to the thread... (not adding much to what RCVideoReviews already said, just getting back to my original comment) >The Power Output of the RC-Link, that is needed when flying with a Video RX/TX will never be anywhere near what is needed for the Video Link. I Don't fly long-range, so I can't speak to that, but at ELRS-150mW, the RC-Link is way, way, more powerful than my DJI-V2-1200mW. I can' not find a use for the ELRS 2-Watt Power Output, when I am using a Video Link. >If you need the full 2-Watts ELRS RC-Link, then you probably already know a lot more about radio than I do. Happy flying everyone!

A few things have changed in RC since i built my Galloping Ghost transmitter including forming the aluminium case, so this update on recent developments is very useful, thanks. Can you attach one of these express lrs modules to an ordinary tx?

@RCVideoReviews

3 ай бұрын

You're welcome.

Thank you so much for this. Quick question. When will the Boxer be added to the device list?

@RCVideoReviews

Жыл бұрын

You're welcome. Boxer is available if you select 3.2.0.

@barry_dalive

Жыл бұрын

@@RCVideoReviews OK Thank you!

@RCVideoReviews

Жыл бұрын

Anytime

Would you consider doing a how-to on how to change the output to 2 watt on the Ranger Module?

@RCVideoReviews

Жыл бұрын

Since that basically violates Part 15 compliance, I won't be showing a video on how to do it. Sorry. It's on YT if you really want to know.

Took a second with the silicon labs drivers

Quick question, is this same for setting my drone? Thanks.

Hey man, if tbs agent lite is up to date on my tango 2, do I also need a elrs lua then this dongle and follow the procedure. Except select tbs tango 2!

I also have a Rekon 5 long range. Would i need to flash again everytime i use my radio?

Might be a stupid question, but does my Tx16s need to be on Edge TX to have ELRS to function or will ELRS work on OpenTX software?

This used to be a simple hobby. A lot has happened since I built my last heli in 1985. People used to think I was smart because I knew what a Schmit Trigger was. No more.

@RCVideoReviews

Жыл бұрын

The tech is advancing at a rapid pace, that's for sure.

@MontegaB

Жыл бұрын

I kind of see this as a separate hobby, honestly. In my youth R/C was more about modeling, and the more "scale" you were the cooler. R/C drones are a different animal. It's more about the bleeding edge of technology and riding this wave of super fast development. Luckily R/C modeling still exists, and Futaba will still happily sell you a radio for that.

@ramtek2702

Жыл бұрын

@@RCVideoReviews Well, I'm 76 years old. I doubt I'll live long enough to even catch up.

@ramtek2702

Ай бұрын

@@MontegaB It just dawned on me that the only flyers needing ELRS are drone pilots so I must agree that this is a hobby unto itself. I bought a Boxer with native ELRS but I doubt I will ever use it in an aircraft. Maybe I should go look at what Futaba has to offer. Could you elaborate a little, please?

@MontegaB

Ай бұрын

@@ramtek2702 ELRS is great for aircraft, too. There are ELRS receivers with servo outputs. The protocol is very robust, long range and is comparable, if not superior to the major aircraft radios. I would highly recommend it. I am converting a Thunder Tiger Raptor 50 nitro helicopter from a spektrum DSMX receiver over to ELRS because it's more reliable.

Hi sir I have a question what would ur advice be I wanna add elrs to my ground control for my Rc car ? Ps u are the first guy I’ve Hurd say what u said In regards to neubs!!! Amazing sir u are awesome 😎

@RCVideoReviews

Жыл бұрын

I'd say I love ELRS and trust it with expensive planes far away. If you have a ground based radio that supports ELRS tech--I would say use it without a moment of hesitation. Glad you found the video useful. Thanks for the comment.

@nutsnbolts4601

Жыл бұрын

@@RCVideoReviews yes radio link RX eight has a wire that connects straight to the ELRS system through the USB or a small battery but my question to you is do you know how to connect this to an RC car

Great video. But I'm still unsure why I might want to use ELRS for my airplanes instead of the 4 in 1 module. I'm not doing FPV or drones. Thanks

@RCVideoReviews

Жыл бұрын

$15 Rx's, no fear really of signal loss, ridiculously easy to bind with binding phrases, tx can travel from radio to radio and maintain bind, rapid development in Opensource vs stagnant corporate development, multiple form factors including postage stamp and pwm. I have ELRS in all of my best planes.

@johndd8186

Жыл бұрын

@@RCVideoReviews thanks!

i am awaiting my new mt12 radiomaster 4 in 1 surface radio and have a nano elrs module.i will be updating to the latest firmware. my question is do i plug the usb c direct into the module or do i plug module into radio 1st and then use the data port on the side of the radio. will the installer read the external madule so i can flash it or can i just flash it when not connected to the radio

I think that it should be more clear from the beginning that ELRS will work much better for iNav than for Ardupilot due to lack of full telemetry support for the latter. Deal breaker for many.

So its not possible to flash thru the TX16S when the module is inserted into the Jr-Bay ? I have flashed FrSky Rx's via the TX thru the UART and made a servo cable that had switched two pins.

@RCVideoReviews

Жыл бұрын

No, you can't flash external modules through the module bay.

I am a complete beginner and have got the pocket cc2500 to and have the elrs nano mod on its way. I have real flight trainer simulator with a ws 2000 dongle which I am unable to bind with, I am hoping that with the module that it will bind. If it still won't bind have you any suggestions

Hola amigo 👋 Ufff he tenido que esperar algo de tiempo para poder ver este increíble vídeo porque al ser en vivo KZread demora algun tiempo en tener los subtítulos y en mi caso necesito el idioma Español. Pero bueno ya todo listo, logré ver el vídeo completo 😃 y me ayudó muchísimo, aunque debo admitir que te he estado preguntando mucho por el Discord jajaja, gracias por ayudarme rápido por allá también. Tengo varias preguntas: 1- Cuando estás con el tema de actualizar el módulo ELRS, primero dices que lo conectas a una fuente de energía y luego dices que lo conectas a la computadora, básicamente pensé que la fuente de energía era la computadora desde un inicio y si me equivoco por favor 🙏 corrígeme. Solo pretendo actualizar por UART pero el conocimiento es poder y siempre hay que saber el potencial de cada equipo que esté en nuestras manos para sacar el máximo rendimiento posible. 2- El fichero o archivo LUA que colocas en la radio, de dónde se descarga? 3- Pretendo utilizar los nuevos receptores ELRS/PWM de Radiomaster y lógicamente no es igual que ese receptor que actualizaste por lo que me gustaría saber como hacerlo por UART. Saludos desde Cuba 🇨🇺 Excelente trabajo 👌 y gracias por tú tiempo. Sigue asi 💪

I’ve lost my 3 position mode switches with stitching to ELRS. Is there a way to get this functionality back?

Hello! I have a quastion: why does my ranger module purchased on 12/23/2023 not have an "accelerometer / Motion Detect" section in the settings?

I have Radiomaster Boxer 4-in-1 , And I want to use Express LRS, Does it just bin and fly or need something else to make it work ?

@RCVideoReviews

Жыл бұрын

You need LUA to configure. Highly advise use of binding phrases. Works directly with Boxer.

I also have a radioking radio, would the Lua script work?

How do I get head tracking for ELRS? (I use a motionsic tallyho tracker)

I have a radiomaster TX16S MKII ERLS. When I attach my 900mhz bandit it doesn't turn on. You know why?

K my issue is that I just got the radio master boxer with built in Express ELRS, Crossfire, 4&1. Now i did the whole process on downloading the black sheep TBS Configuration. But for some reason, my TBS agent is not working on my controller. It’s saying something like error value. I’ve copied the TBS agent files to my USB on my radio, I followed the instructions to the T on Joshua’s (from Roto Riot), KZread video on how to download the files. I didn’t need a module for this saying that my radio has it built in already. So I don’t know how to get the TBS agent to stop showing a error value. Any advice or link video that shows on how to get this back to working. Also, if I were to do a master reset on my radio, would it reappear as how I first got my radio?

Hi !! - I have same radio - same ranger module - Which baudrate & packet rate you recommend for indoor flying ?

@RCVideoReviews

Жыл бұрын

400k. 100hz is more than enough for most people. Since you're flying indoors, have no fear jacking it up to 1000hz if you want as you don't have range concerns.

@emmanuelcheveau4891

Жыл бұрын

@@RCVideoReviews thanks !! and I love your methodic approach of teaching :)

I got that one but haven't use it yet

What's the best way to add the radiomaster namo erls module to a tx16s running edgetx providence.

@RCVideoReviews

2 күн бұрын

I wouldn't be able to recommend anything here as I would just get a Micro module.

You have to use this dongle on all elrs receivers or just certain ones

@RCVideoReviews

Жыл бұрын

This is a trick question: You don't "have" to use the dongle. You can flash via wifi. All receivers can be flashed with the dongle. I recommend ensuring you have the dongle because on countless occasions I've flashed a receiver using the correct firmware and wound up with a corrupted flash from which the only way to recover was via dongle. This isn't a question of brands, it's a question of what to do if you do everything right, but still get a corrupted flash.

@Deathwish_fpv

Жыл бұрын

@@RCVideoReviews ok cool thanks for the info dude

Quick question ⁉️ will Xjt external module work on boxer?

@RCVideoReviews

9 ай бұрын

It should.

Is this necessary equipment for rc flight in general or just for long range?

@RCVideoReviews

7 ай бұрын

You have to have an RF transmitter and RF receiver. It may as well be this protocol. Can't beat the price, features, or reliability. Nothing else on the market comes close. PS And oh yeah, if you want to fly long range you can do that too. I use this protocol on every line of sight (LOS) plane I have.

@Doggy-B

7 ай бұрын

@@RCVideoReviews my apologies, I didn't word that question very well. I also assumed that the ranger module was just for extreme range. Is the ranger module a must have for the transmitter to work, or does the transmitter still work without it?

@RCVideoReviews

7 ай бұрын

All TX16s come with an RF transmitter. Some are 4in1, some are ELRS. None of them ship absent a transmitter.

@Doggy-B

7 ай бұрын

@@RCVideoReviews gotcha. Thank you

I'm a complete newb. If the drone already have ELRS like the cineape35, where do i go from there?

Hey i can not Find any receivers with pwm that have more than 5 channels how van i use erls in my fixed wings that need more?

@RCVideoReviews

Жыл бұрын

In the video I showed the crsff-pwm-c converter from Matek. That will give you 10 channels. kzread.info/dash/bejne/fK2huJluYrOwd7A.html This also works: kzread.info/dash/bejne/oYmXr6-joLGapZM.html I'm hoping we'll see manufacturers produce some 10 or even 16ch pwm rx's this year.

Hello everyone, So I got a new drone (my first drone), and I have been able to fly it okay. I'm using the Radiomaster Boxer ELRS. However, on the last two flights, it started screaming at me, "Radio signal critical" and fail-safe. anything that i can do, or is this a kown issue? it was not doing in the last 2 weeks that i have been flying it. as soon as i crossover 300 Meters away it goes on telemetry. lost and critical low signal

Can u use the ranger micro in a 4in1 tx16s?

@RCVideoReviews

16 күн бұрын

Yes. It works great in the TX16s.

I am a subscribed. If i do not do fpv, and only flying watching my small foam planes at the local park or a club , do i need ELRS? what do i lose for not using ELRS in my case? tks

@RCVideoReviews

5 ай бұрын

I use ELRS in all of my LOS models. Cost effective, locked on RF, binding phrases, bi-directional CRSF, onboard vbat, plenty of form factors, packet rates to 166hz for 16ch, 333hz for 8ch, opensource development by hobbyists who know what they're doing. To me, this question needs to be flipped: Why on earth would you use anything but ELRS?

@alexherrera3918

5 ай бұрын

@@RCVideoReviews Well put, i only recognize about 1% on the names you listed in your response but it seems that there are many things i am missing from not using ELRS, i will continue watching your videos to learn about it. thanks for your response.

Your video named Express LRS. When you talked what is this, you showed Semtech and talk about lora. It's was not clear ExpressLRS - is a company, software, hardware, technology. Is Lora = Express LRS, etc.

Will any UART usb adapter work ?

@RCVideoReviews

Жыл бұрын

Addressed directly in the video: kzread.info/dash/bejne/c5ibpNGSerGvYLA.html

I have a new tx12, installed configurator... and @ ~ 17:00 i am lost... how do i connect to my tx12? I am a novice... looking for step by step...

@ttaylor9916

3 ай бұрын

wifi is more problematic than that dongle @31:30?

Hi, do I need a flight controller to use expresslrs?

@RCVideoReviews

9 күн бұрын

No. It works with FCs of course, but look at Radiomaster ER series: ER6, ER8, ER4 etc...all straight PWM.

@CptAwilliamse

9 күн бұрын

@@RCVideoReviews thank you very much

How do you use those little rxs with planes when there's only 4 pins

@RCVideoReviews

Жыл бұрын

Did you see the part in the video where I showed the CRSF-PWM-C board? That's 10 channels of PWM out. Here's another video with it: kzread.info/dash/bejne/fK2huJluYrOwd7A.html

@Mikeylikesit1968

Жыл бұрын

@@RCVideoReviews Ok thanks I might give the elrs a try. Do you have to upgrade the firmware on both the Rx and module

@Mikeylikesit1968

Жыл бұрын

@@RCVideoReviews Wish there were videos showing this stuff for airplane guys. It's always quad stuff. What are those Xt60 connectors used on that board and why two There's no videos on KZread showing how to use ELRS for an airplane

@RCVideoReviews

Жыл бұрын

The Rx and Tx have to have the same major revision #. So 3.x on Tx and 3.x on Rx. We covered this in the video. Didn't you see it?

@RCVideoReviews

Жыл бұрын

www.mateksys.com/?portfolio=crsf-pwm#tab-id-4

My next question is what to do with these tiny "receivers". You can't plug servos into them so what do they do onboard the aircraft?

@RCVideoReviews

Жыл бұрын

In the video I showed the crsff-pwm-c converter from Matek. That will give you 10 channels. kzread.info/dash/bejne/fK2huJluYrOwd7A.html This also works: kzread.info/dash/bejne/oYmXr6-joLGapZM.html These CRSF output boards are intended to be connected to some sort of Flight Computer that understands CRSF like Betaflight and iNav. I'm hoping we'll see manufacturers produce some 10 or even 16ch pwm rx's this year.

@ramtek2702

Жыл бұрын

@@RCVideoReviews What good are more channels if there aren't switches/pots on the Xmitter or the ability to add them?

@RCVideoReviews

Жыл бұрын

You should probably start watching my TX16s videos and do a little research. The TX16s can support 32 channels.

@ramtek2702

Жыл бұрын

@@RCVideoReviews Well, I've watched both the videos and I'm sure I can replicate what you did, I just don't know why. Are those tiny boards really the only receivers onboard?

@ramtek2702

Жыл бұрын

@@RCVideoReviews I'm attracted to the new BOXER. Do you know when it will ship? I don't have any plans for even 16 channels.

What about the 2watt hack with the big one? Is that real?

@RCVideoReviews

5 ай бұрын

Yes, the hack works.

and now we know we can do 2 watts with the ranger.

@RCVideoReviews

Жыл бұрын

Yes you can :)

What if u fly in the city how much power can someone get? Cus I live in big city .

@RCVideoReviews

Жыл бұрын

Many ELRS TXs can go up to 1w of radiated power. Check the specs of the TX you're interested in. Some have been known to go as high as 2w.

@55amps

Жыл бұрын

@@RCVideoReviewshow’s the penetration? I fly in a open parking space with obstacles

@RCVideoReviews

Жыл бұрын

The only way to know the answer is to go test it. This is 2.4ghz and subject to the same laws of physics as all other RF.

@55amps

Жыл бұрын

@@RCVideoReviews ur video help me, 👍🏼 what’s the best settings for penetration?

trying for a week and still not bound yet, time to bin it ..

57:00

Please have chapters in videos longer than 10 mins. 😵‍💫😵‍💫😵‍💫 thank you.

The question on long range should be more about penetration which is a whole other ball game. There is so much that can be talked about on penetration…

@RCVideoReviews

10 ай бұрын

The question on long range should be about video. Even at low power levels, ERLS is going to severely outfly most video tech without deploying some fairly advanced capabilities (antennas and trackers). When I flew long range, I kept RFLOS in mind so the farther I went, the higher I flew and that does not require penetration. I never saw a 3000ft tree, but I have seen a 3000ft mountain. Anything beyond 3 miles is going to quickly become much more of an issue about video than control link if using ELRS.

@KMProtectionServices

10 ай бұрын

@@RCVideoReviews I have seen many lose radio link in the mountains before video. What you say is true but sometimes penetration on video vs transmitter work different. I think it can be very close in penetration situation which may cause the following: low video reception, and lost transmitter causing drone to drop usually making reception worse if falling further behind interference and then losing video completely. It may all happen so quick that you just see your drone drop... Hard to tell without actual penetration testing...

@RCVideoReviews

10 ай бұрын

I never flew long range in a way that would compromise my control link. Don't even comprehend the notion and what you're describing is probably why the government limits this activity. In my experience flying long range, video was always the first to go. 100%.

@KMProtectionServices

10 ай бұрын

@@RCVideoReviews Government does as they do... more rules and regulations and they never do anything good.... People will still do dumb stuff as they always have. There is a lot that can go wrong but under usual conditions video should go first. I just saw a video yesterday where the TBS crossfire failsafe and crashed 150 yards LOS away from pilot and the video was fine. Clearly something else going wrong...

@RCVideoReviews

10 ай бұрын

Yeah, that's not the protocol. If all systems are operating properly, video should go first.

Hey Joshua I think I may have messed up my Jumper T Pro V2 by trying to attempt an update. I watchbyour videos all the time and was wondering I you can help me with this? Maybe email would be best! Look forward to your reply thank you in advance

not excited at all with ELRS, I have tx16s mkII and on config i click expressLRS screen just get blank and does nothing. firmware update didn't helped at all..:(

@RCVideoReviews

2 ай бұрын

Did you turn the model on in model settings? Did you set a baud rate in system settings? ELRS works. If you're having issues, it's either hardware (possible) or configuration related (probable). Get on discord and we'll help you there. Link is in the description of every video I post.

4-hrs late to the party. At your flying field how many people has switch to OpenTX or EdgeTx/LRS? At LFERC only 5 out of 250 members.

@RCVideoReviews

Жыл бұрын

I have no way of knowing that. I know I've seen Radiomaster and Edge out there, and I've had a couple members approach me and tell me they follow my videos. As far as total users--no idea.

Dongle is $13

@RCVideoReviews

Жыл бұрын

Sounds about right.

Not for me, no fun to much work and too much to go wrong. I'm not into computers but I have to use one with basic stuff.

@RCVideoReviews

Жыл бұрын

It's not for everybody. Sometimes simple is just better.

Drones are not a hobby......its just camera

@athenovae

Күн бұрын

Lol what? Everything that goes into getting a camera in the air and having control of that camera view is the hobby.

the ranger has 2w capabilities, was just stating this cause in the video it was said all were the same

@RCVideoReviews

Жыл бұрын

From the factory, they are all the same. Using 2w usually means you'll be using it outside of Part 15 compliance, so I don't advocate for that or show how to do it.

Thanks 🙏

@RCVideoReviews

Жыл бұрын

Yes

@bsr3280

Жыл бұрын

Thanks

Hey man quick question, I'm trying to build and flash for the first time my Axis Thor tx and it keeps saying flash error, and under the log it says- A fatal error occurred: Failed to connect to ESP32: No serial data received. I have the correct driver installed from silicon labs, can you possibly point me in the right direction on how to resolve this frustrating situation?

@RCVideoReviews

Жыл бұрын

Flip rx and tx?

@steelrainfpv3383

Жыл бұрын

@@RCVideoReviews I tried switching to that option with no luck, even tried several different usb-c cords including the one that came with my phone and still the same result. My tx came with version 2.5.0 and it won't update to any of the newer elrs versions, they really need to work on streamlining this whole process like Crossfire.

@steelrainfpv3383

Жыл бұрын

@@RCVideoReviews so I finally got my Axis Thor tx to update from it's factory setting of 2.5.0 to 3.2.0 via it's own wifi interface and web browser, along with my two Matek R24 P6's (man those soldered pin headers bring me back) via the same method, so it's all good here minus my understanding of why the uart method kept failing. Quick question: what do you prefer to use as your best elrs pwm board for 6 plus channels in fixed wing models?

@RCVideoReviews

Жыл бұрын

I like the Matek CRSF-PWM-C. It's 10 channels, but has voltage and current. If you can get by with just voltage, the CRSF-PWM-6 is pretty nice.