Installing the OHTOKC CDI conversion kit on Honda Z50
Installing the OHTOKC CDI conversion kit on Honda Z50 this kit is for the early Z50 with the HITACHI FLYWHEEL will not work with other flywheels
Installing the OHTOKC CDI conversion kit on Honda Z50 this kit is for the early Z50 with the HITACHI FLYWHEEL will not work with other flywheels
Пікірлер: 62
This is an awesome video! I am fixing up a '79 Z50R my brother in law found rotting in a ditch. I just got the motor running on points but I was considering upgrading to CDI down the road, now I am convinced!
@2strokeguru
2 жыл бұрын
Awesome thank you
@timkilgallon2098
Жыл бұрын
Did you use 1 of these CDIs ?Was it any good? Tim.
Another awesome video Kevin. Im watching this cdi conversion stuff, to see what all is avaliable . Great job
@2strokeguru
3 жыл бұрын
Lots of fun im vary happy with it
@timkilgallon2098
Жыл бұрын
@@2strokeguru Did you get one of these CDI ignitions? Im looking into getting one but as yet Iv not got any feedback from anyone who has used one. Tim.
So many gems. Thanks Kevin
I have a 77' Z50 that's been in my garage for 22 years. I'm installing the same conversion right now. I needed to see where you put the ground and module. I didn't drain the oil before I took off the back plate. Just a mess. Anyway, , Great video and Thank you for Sharing/Teaching.
@2strokeguru
3 жыл бұрын
Under the seat and the coil mount nut
@timkilgallon2098
Жыл бұрын
Hi I'm wanting go fit one of these to a Yamaha dt125. Are you happy with yours ? Any problems? Tim.
@austinl.2703
Жыл бұрын
@@timkilgallon2098 Hi. I put it on there and got it started several times very easy and with a small funnel for gas feed. In the mean time I got a new gas tank and fixed the brakes. I didn't start it for a long time. So now it's February 15 2023. I can't get any spark from it. I'm waiting for a response from OHTOKC for how to test it.
I just watched this video. What a video very nice kevin. The little 50z ran perfect.
@2strokeguru
3 жыл бұрын
it came out great
@LarryJohnson-tc7xc
3 жыл бұрын
I just looked at a vape dynamo cdi ignition change over kit for 70-75 kawasaki's the f7 f9 f11 almost $700. It must be made out of 25kt pure unrefined Egyptian gold.
@2strokeguru
3 жыл бұрын
@@LarryJohnson-tc7xc wow thats crazy
Just ordered one for my 78 👍
dude that was a sweet video and a dope little bike, can't wait to do that to mine!
@2strokeguru
2 жыл бұрын
Thank you
@timkilgallon2098
Жыл бұрын
@@2strokeguru Did you get round to fitting one of those CDI units? Good or bad? Tim
@2strokeguru
Жыл бұрын
@@timkilgallon2098 cdi on the z50 works awesome very happy with it
Great job! Great vid👍
@2strokeguru
3 жыл бұрын
Thank you
Air filter boot for the ke 125 is 100 bucks they made 10 of them sold 4 . There is also a cdi 12volt lighting conversion for the 125 . but it real money . Like 500 bucks ... I set my 74 ke125 up with it . Also set it up with the tubliss system for my wheels and set it up with a set of Michelin star cross 5's . Mine looks like it came from Ken Kaplan's museum.
@plusblood5101
Жыл бұрын
U r correct That stupid rubber boot Almost $99 plus t. And shipping chaRges I will create my on conversion Hell with that $99 bs
there great little bikes i got 2 1976s they only made yellow 1 year
@2strokeguru
Жыл бұрын
Lots of fun I enjoy mine I am building a 2stroke version using honda mb5 engine
@mikeatv
Жыл бұрын
@@2strokeguru nice !!
OHTOKC is building me a CDI conversion for my 76 ts100 with the 2 bolt style points plate. im very excited to get this bike running.
@2strokeguru
3 жыл бұрын
That's awesome
@johncasertano1687
3 жыл бұрын
i am trying to get one for a 1974 tc 100 i had to give them measurements have not heard back yet .probably need same one as you did .how much is it?
@2strokeguru
3 жыл бұрын
@@johncasertano1687 this unit will not fit your bike i am working with the manufacturer to develop different products
@kevintribbey4313
3 жыл бұрын
@@johncasertano1687 if your communicating with OHTOKC. sometimes theres a delay with responses. i went through the same process of sending measurements. i was talking with them since late January of this year and got the part in the mail this week. i wasnt in a rush. im very happy the time and patience they had making me something from picture measurements sent. once shipped, it only took 1 day to reach the US and 3 additional to make it to my doorstep.
@johncasertano1687
3 жыл бұрын
@@kevintribbey4313 thanks for info. let me know if it all worked properly
I'm am doing up a Yamaha dt125. I'm looking to fit CDI ignition, have you or anybody had any problems with this system? How many would recommend one? I enjoyed the Vid, I usually put a bit of oil all over any O rings or seals before I fit them. I know you don't want to get debris into the engine but would filing a chamfer help with the O ring? Tim
Will it keep a charge on a 6v battery?
do you think it will fit a 1970 125cc Harley Davidson aeramacchi rapido mls ? 6 volt battery i will be modify it
@2strokeguru
Жыл бұрын
That I don't know I don't buy AMF it's only a harly by name
Hi Kevin, the coil on my 1980 ts100 went bad and I cannot find a replacement (P/N 33410-48520). Suzuki made this specific years coil different than others by integrating an ignition control unit into it, so universal replacements don’t work. My only option I think is to go with the Ohtokc CDI conversion for ts100. It states that it will work with a Nippon Denso flywheel but my flywheel is stamped FP4191, do you know if it will work? Thanks
@2strokeguru
Жыл бұрын
No it will not work send me pictures of the original coil text 603 395 8097
@CaptainZoop
Жыл бұрын
Pictures sent
hello, do you have a link from the website where you bought it? I see many on the internet, but I can't find the model you installed in the video
@timkilgallon2098
Жыл бұрын
I found them on the net type in OHTOKC. Did you manage to get one ? I'm looking to get one for a Yanaha DT. Are they any good
I just installed that CDI system on my 1978Honda Z50 and after I have a very weak spark any thoughts on this issue?
@2strokeguru
2 жыл бұрын
Use a resistor spark plug so take the original plug to the parts store and ask same plug but in resistor
@timkilgallon2098
Жыл бұрын
I'm looking to fit one of these to a yamaha, did you get yours sorted out? Tim.
I have a 1982 50R, can the stock flywheel be swapped out to the hitachi flywheel? Then do the conversion?
@2strokeguru
3 жыл бұрын
The Hitachi flywheel will not work the taper on the shaft is different
@barthoward4119
3 жыл бұрын
@@2strokeguru thanks for the info. found this on a forum about the different tapers. S cranks are the 3 speed 6V cranks. L cranks are your 4 speed H 6V variants. Type R cranks are the 12V cranks. There was also a G crank that was produced on some 6V Honda monkeys overseas between the L and the R cranks.
Can you add a link for the magneto?
@2strokeguru
2 жыл бұрын
Ebay.com unfortunately it won't let me type in honda z50 cdi
Ohtokc made in Malaysia...good
@2strokeguru
Жыл бұрын
Yes I have had great experience and luck with this ignition system
Kevin is there a cdi conversion kit available for a 1986 z50r 6 volt Mitsubishi flywheel? Kevin is there a cdi conversion kit available for a 1986 z50r 6 volt Mitsubishi flywheel?
@2strokeguru
3 жыл бұрын
No only for the Hitachi