Never use an old split pin! Never. Clean all parts and a little bit grease for the joint are always good...

@FairladyS130

3 ай бұрын

Grease attracts dirt and used split pins are fine if they are in good condition.

@detlevschliesser152

3 ай бұрын

@@FairladyS130 🤣🤣🤣

@ActivityPhoto

2 күн бұрын

Split pin? Never heard it referred to that before. I believe it's technical name is a cotter key.

This is the correct adapters for these mini boards if you look at those ridges they are supposed to interlock with the mini pedal to prevent from slipping or moving around. Ok I have sent you enough messages. I placed the order and returned them other ones Installed Kuryakyn Riot Mini Floorboards, Honda CB500FA mirrors, and added frog grips tonight. Can't wait to test them out.

I looked at your video again you might want to look at your install maybe its secured right now but in the long run the thing is going to move

When you want to pull a cotter pin out, put one of the needles of the needle nose in the loop of the pin and tap on the needle nose to get it out.

How did you manag tonscrape the pedal assambly that is way high.

that is what I need that's for the video ... where did you buy your c-14 adapters

@motocatz87

Жыл бұрын

Amazon...Puig 6347N Black Pilot Footpeg Adapter - Pair

have a link for the floorboards and adapters used?

@motocatz87

9 ай бұрын

I have a hard time with linking, but the kuryakyn mini boards and the C14 adapters can be found on Amazon.

What size bolt did you use to connect the adapter to the mini board and where did you get it? I bought these exact adapters and mini boards and neither came with bolts.

@motocatz87

11 ай бұрын

I used the same bolt that connected my original pegs. I don't know the size, you might have to look it up in the manual or call Honda.

@crueguru1

11 ай бұрын

@@motocatz87 Thanks, but I'm not talking about the bolt that goes through that uses the codder pin. I'm talking about the screw that you used the T-handle to tighten down that goes through the mini board and into the adapter. My adapters did not come with them. I think they're called socket cap screws

@motocatz87

11 ай бұрын

@@crueguru1 It's a 6mm socket bolt. I realized that these bolts come with Kuryakyn boards.

How do you like the floor boards now that you have been riding them I went for a 4 hour ride on my rebel 2022 DCT and I hated the foot pegs

@motocatz87

10 ай бұрын

There is no comparison, the Kuryakyn mini boards are way more comfortable. I would never go back to those stupid pegs...ever! I feel like my foot is way more stable and it's very comfortable. Just make sure to tighten them up with some torque. Look in the manual for the correct torque. I tried to do 25 lbs of torque, but I felt I was pushing it, so I went down to 20, now they don't move at all. One thing to be aware of, I move my bike around in my driveway, so a couple of times I hit my lower shin on the boards. I had to get used to the distance to not do that. Now, I have no problem. Take the plunge and get them, you won't be dissapointed.

@capicapuchino5675

9 ай бұрын

Thank you very much I just got my rebel and going through what upgrades I want to do love your videos @@motocatz87

Where did you buy the boards and adapters

@motocatz87

2 ай бұрын

have a hard time with linking, but the kuryakyn mini boards and the C14 adapters can be found on Amazon

Hello I have a Honda Rebel 1100 DCT do you by any chance know the Kuryakyn Riot passenger peg model number also if there is an adaptor that model number ??

@motocatz87

7 ай бұрын

I'm sorry I don't. There is a Honda Rebel 1100 DCT on Facebook that you can join. I'm sure someone on there will know. If not, ask Rebel On The 11 here on YT and I'm sure he will know. Best of luck to you.

OK I need to ask you a question I received exact the same adapter C14 and the kuryakyn mini pedal and I think that adapter should go in the hole of the pedal when I was watching your install I didnt pay attention to that part because I truly feel that male part of that adapter should go into the hole and its too big I will need to contact Kuriyakyn and ask

@motocatz87

9 ай бұрын

I think your right, something is off. They have moved a few times when I've used them to get on and off my bike. I thought I just needed to use blue locktite on them, but they shouldn't be moving at all.

@thomas5040

5 ай бұрын

It appears you are using Puig adapters. You need the 8889 Kuryakyn Splined Peg Adapters.

Sold out 😢 Unable to locate this c-14 adapter either

Did you have to order an adapter for the mini boards?

@motocatz87

10 ай бұрын

Yes, C-14 adapters on Amazon.

@williamcoulter5462

3 ай бұрын

You need the 8889 Kuryakyn Splined Peg Adapter not the ones used in the video they are the wrong ones I have them on my 1100 and they do not slip as they use the splines to grip the foot plate. I ended up waiting months for the adaptors to be in stock.

How do you find the DCT in stop start going?

@Samuel10463

Ай бұрын

Effortless, much better than manual.

Super awesome video awesome motorcycle. I just bought a 2022 Honda Rebel 1100 DCT only 260 miles $8100 absolutely love it. I’m doing upgrades and I saw you in here . I love your windshield where did you got it?

@motocatz87

3 ай бұрын

Hi there mousebowen. What a great deal you got on your bike! I got my shade from Memphis Shades. Its great, it makes a big difference with the hwy speeds.

@MOUSEBOWEN

3 ай бұрын

@@motocatz87 awesome I absolutely love the way it looks . Was affordable?

@motocatz87

3 ай бұрын

@@MOUSEBOWENI think it was because I bought things little at a time and usually during a holiday where I would find things on sale. Like my Burly sissy bar was on sale at the time on the Burly website and I got a free leather bag with it.

Pardon my ignorance What is the adapter for again?

@motocatz87

Ай бұрын

Puig 6347N Black Pilot Footpeg Adapter - Pair

@captainobvious5349

Ай бұрын

@@motocatz87 Yes. But what is it for? What do you need it for? To make it fit or to extend the footpeg morr outward?

@motocatz87

Ай бұрын

@@captainobvious5349 To make it fit.

I took out this pin from this screw ( not a screw) ? And tapped it with my wrench ( not a wrench) then forgot the washer and faffed around with the split pin, .sorry but this was a difficult watch.. 😢

@motocatz87

3 ай бұрын

Oh gosh, sorry about that. I actually need to replace the pins because someone on here told me to never reuse the same pins you take out cause they can fail.

@captainobvious5349

Ай бұрын

Wow. I bet you're a real hoot at parties!!

@motocatz87

Ай бұрын

@@captainobvious5349 lol...

Cute dog! What is it?

@motocatz87

4 ай бұрын

He's part chihuahua and pomeranian :D

Girls😂

Nothing annoys me more about watching videos from people that don't know anything about mechanics is they call things the wrong name. For instance I'm less than three minutes into this and she's called a pliers a ranch, she's removing a clevis pin and called it a screw.

@motocatz87

2 күн бұрын

Hey there ActivityPhoto, thanks for stopping by! I would like to think I’m less annoying than a toddler throwing a tantrum in a seat next to you on a plane…but I guess my video is far more annoying. You’re too young to be annoyed by my ignorance in the names of tools. I’m sorry about that, but then again, I never said I knew about mechanics or the names of the tools I was using. I simply made a video to show how to put these mini-boards on. It’s not to offend people or to annoy anyone like yourself.