I just did this mod and started flying the TinyGo with my TX16S (ELRS) today... I love it!! Luckily I did NOT have to install the 1K-ohm resistor. When I built my configuration, I used EdgeTX passthrough to load onto the controller and Wifi to load configuration from my cellphone. I had some other challenges in getting set up in Beta Flight... but thanks to your video (and a couple others) I was able to get it to work. Interestingly, this is my first FPV drone ever.... my other quads are the Mavic 2E and the Mini 3 Pro. Can't wait to build a drone from scratch!!! Thanks for the great videos

@OneManUnmanned

Жыл бұрын

That's awesome! I'm glad it all worked out.

@parkour_dad

7 ай бұрын

@blueadv214 What did you do in Betaflight to get it to work?

Oh Man, thxxxxxxxxx allot. I had same issue trying to figure out the problem (something work, sometime not) and you just saved me big headache!!!! now it is working like a charm

@OneManUnmanned

11 ай бұрын

Thanks…I’m glad the video helped.

Followed this tutorial and used a RadioMaster receiver; I actually did the swap before I ever got the drone flying in the first place. For some reason my board thinks it's backwards so I had to compensate for that. The Radiomaster pocket controller is a joy. Now to replace the vtx/camera that never worked right either. They sent me a real dud but glad it's going now. I did an absolutely horrible solder job but it still works :)

@OneManUnmanned

2 ай бұрын

Thanks for the updates…I’m glad you got it working.

P.S. You should consider the Ph2.0 Pigtail to XT30 conversion. Once you do that, the TinyGo is 2s/3s. I did that mod and was amazed with its new capabilities.

@OneManUnmanned

2 жыл бұрын

I'm thinking about it.. I'll be doing some more mods to this drone in the coming weeks. I'll seriously consider it then.

You did it you crazy summamabish! You did it!

@OneManUnmanned

2 жыл бұрын

Haha.. finally!

Very helpful video. I had a similar thing happen on a recent build with the GEPRC FC for DJI. I built a really light naked vista based around the Happymodel Crux3, but using this flight controller. I had already flashed and bound my ep2 using a bench power supply. The problem it caused me is that the drone would fly when tested-------until I plugged in the naked vista. Then the ep2 would stop communicating. I didn't do the research you did. I had a crossfire nano lying around and used it instead, which fixed the problem. That said, I'd much rather have the EP2 on such a tiny build just to not have to fool around with an external antenna and to save a few grams, so I am ordering some resistors today. Thanks!

@OneManUnmanned

2 жыл бұрын

Uh man, that sucks..Apparently some GepRC FC have this issue with ELRS receivers. I have no regrets in switching though. I'm glad the video helped. Thanks for your insights..Hopefully it helps other pilots as well.

@kurtzFPV

2 жыл бұрын

@@OneManUnmanned I just hit the bell on your channel. I try to watch whenever they pop up, but for some reason, the KZread algorithm had quit sending them my way. Anyway, it was pretty random that I happened to watch this video tonight and once I saw the flight controller you were using, I kept watching because of my experience with it. I was trying to think of some hashtag or something you could add that would help for people searching for this solution, because I am sure we are not the only two that have had this problem, and this clearly illustrates how to fix it.

@OneManUnmanned

2 жыл бұрын

I appreciate you watching the video...As far as the algorithm, YT does not honor the Subscription button(or bell) like it used to. It will only push content it thinks you'll watch, or relevant content that you've watched in the past. Having said that, I appreciate you hitting the bell nonetheless. I will try to better use the hashtag so that my content is searchable.

@kurtzFPV

2 жыл бұрын

@@OneManUnmanned You have great content and production value. I know it is slow, but you'll have a ton of subscribers at some point if you keep them coming.

@OneManUnmanned

2 жыл бұрын

Thank you...I hope it happens eventually. Thanks for the encouragement.

Thanks!

@OneManUnmanned

7 ай бұрын

Thank you Very much..I appreciate the support.

Great job with the tutorial. Very clear. Thank you.

@OneManUnmanned

2 жыл бұрын

Thanks..I appreciate that.

Great video..👍.. some nice information on a bricked receiver..

@OneManUnmanned

2 жыл бұрын

Thanks..I appreciate that. It's a longer video than I wanted, but it's good to post my experience for transparency and to help other pilots.

Very helpful. Great video

Lol you guys leaving your QC PASSED stickers on your drones. TACKY ASF!!! LOL

@OneManUnmanned

6 күн бұрын

haha..

I Would like to see a video about RSSI. 2 of my mine start with an rssi of 20 instead of 99. I have setup them up the same in betaflight.

Hello One Man, I have the same problem with my tiny go and the ERLS and still couldn't match it, but now I think I have understand what is the problem, I need to connect the 3v3 to the rx righ¿? but I have the beta fpv tower antenna and radio lite 2 se, so do I need a to use a pull up resister to connect or could be any other simple cable like the blue, yellow or white one. I will appreciated so much you help cause im new on this world and after a month since I bought it and a lot of simulator, could make a few flights, then I discovered the erls world and decide to get into it by my self but now can't fly cause I couldn't match it and till now, i didn't now why, but I have the answer thanks to you. I really don't understand too much about electronics components so I´m not sure if need the pull tip resister or can use any other wire and don't burn it. Thanks hermano for the info and hope you can resolve my doubt

Hey thank you very much for your extensive reviews and in-depth mods. are you going to convert the tiny go to the 03 unit from.dji since the beta fpv pico and the happymodel mobular8 o3 seem to be very popular builds?

@OneManUnmanned

Жыл бұрын

Thanks a good idea..I did not plan on doing it, but am interested in the smaller HD drones like Pico and Mobula8.

Is it possible to connect Frsky R-XSR 4-10V 16CH FPV to TinyGo 4K?

@OneManUnmanned

Жыл бұрын

I don't see why you couldn't wire up an Frsky receiver to it.

So am I right? Receiver G -> G FC Receiver 5V -> 5V FC Receiver Tx -> Rx FC Receiver Rx -> Tx FC & Receiver RX -> 1kOhm -> 3.3V FC Also do you need to remove the resistor after flashing and configurating the receiver?

I know this is a year old but hoping you might be able to help me out. I am trying to do the same thing to my newly acquired Thinking P16. I have a HappyModel EP1 soldered to the UART2 of the fc. I was able to connect to the wifi hotspot and update it to version 3 to match my radio. I go into BetaFlight and enable the Serial Rx on UART2. I have telemetry with my radio but see now stick/button movement on the Betaflight Receivers tab. What am I doing wrong?

@OneManUnmanned

7 ай бұрын

I don’t know what version of the Configurator you’re using, but make sure the UART for the receiver is correct in the Ports tab and Serial RX is selected. If your go to the Receiver tab, the Serial Receiver Provider needs to be “CRSF” and Receiver Mode needs to be “Serial”. Don’t forget to safe after you make those changes.

@parkour_dad

7 ай бұрын

@@OneManUnmanned Wow thanks for the quick reply. I definitely enabled the Serial RX on UART2 and checked the Receivers tab to ensure that Serial and CRSF were selected. I also double checked the RX from the receiver went to the TX of the fc and TX to RX. Am I missing anything else?

Hi. saw your video and learned the command for rxrange to delimit points. I have a problem, my drone after update, is not flying, when I turn it on, it activates the engines and jumps like in turtle mode. I noticed that in betaflight the yaw control is at the maximum 2000, I already put the old firmware and it was the same. In the control tab, the drone is rotating and the yaw on 2000. how to configure it to be in the middle (1500)? And also on the PID tab, all the commands go from 0 deg/s- 667 deg/s, when I turn on the radio the yaw goes from 0 to 667deg, while the others remain at 0 deg

@OneManUnmanned

Жыл бұрын

What radio are you using?? It sounds like your stick inputs are at full and continuous.

Спасибо очень помогло! Thanks!😊

@OneManUnmanned

Жыл бұрын

No prob..Thank you!

Is there a way to connect GR8 to a PC to play with simulators? I thought I'll be able to fly some hours with it before I start crashing my TinyGO 4K into walls but there's no bluetooth or USB port on the radio. It's a shame because I've got a VR set, I've got a simulator, I have this radio in my hands and it's snowy -20°C winter (that's -4°F) so batteries will die outside. All I'm missing is a way to connect all that together.

@OneManUnmanned

Жыл бұрын

There is no way to connect the radio to a computer hence why this video is so valuable. I've mentioned it here in other videos: kzread.info/dash/bejne/mZNr1quSpbC1gLQ.html kzread.info/dash/bejne/e31tzMqLptXeYag.html The TinyGo can be flown indoors..I would suggest Angle mode while learning, if it's your 1st FPV drone. Here is the setup and 1st Flight video: kzread.info/dash/bejne/hZuZxauLd7WoZ84.html kzread.info/dash/bejne/g22lr6yTY5nJlbA.html

@cprn.

Жыл бұрын

@@OneManUnmanned Thank you very much, I'll study those religiously! BTW I've found out there's a way to connect any 4+ bit chipset flight controller to a PC (the guy in the video says F4 or F7 controller, I'm guessing it means available memory bits) but it requires flashing and either dismantling the drone to get that flight controller or buying an extra one (or connecting and powering up the controller *in* your drone which will probably require to connect the battery and risk the drone flying off and ripping connectors). You connect the controller to the PC via USB, set it to act as a USB joystick with Betaflight and then bind the radio to the controller. Here's a video: kzread.info/dash/bejne/qamjxNyop6_MmpM.html

@OneManUnmanned

Жыл бұрын

Cool.. maybe this info will help others in the future. Thanks!

Is there a special reason you are using leaded Pb solder (blue) instead of lead-free (green) solder ?

@OneManUnmanned

Жыл бұрын

No, not really. It was the one available at my local store.

In regard to the receiver swap, I chose Crossfire to match my other quads. It is great to fly it with my Tango 2.

@jakestyles002

2 жыл бұрын

The Crossfire Nano just wired up to the existing four wires to the stock receiver.

@OneManUnmanned

2 жыл бұрын

The ELRS receivers can be "finicky" sometimes. I'm glad you had success with CRSF. The Tango2 is a great radio and still sought-after today.

Which is better in your opinion tiny pro or ez max pro pilot? Thanks Tracy Johnson

@OneManUnmanned

Жыл бұрын

I'm not sure what drone is the Tiny Pro..I think you meant the TinyGo. TinyGo vs EZ Pilot Pro, I would say the TinyGo is better. It has a more capable drone that can fly indoors and outdoors as well as record in 1080p or 4K. The goggles that come with the EZ Pilot Pro also does not record video(has no DVR).

Hi you remember me? I'm one of your early subscribers

@oulkismi2848

2 жыл бұрын

And I love your vids

@OneManUnmanned

2 жыл бұрын

Yes, thanks for your support..I appreciate it. 🙏

Best place to buy this drone?

@OneManUnmanned

Жыл бұрын

All Links are listed in description..GEPRC seems to be the best place to buy.

@jamesjimmy9634

Жыл бұрын

@@OneManUnmanned ty. Where I was gonna buy. Think will be good starter fpv for my 14 yo son. Last drone bought him was decent. But think this will be good xmas present. I might get one too. Ty

@OneManUnmanned

Жыл бұрын

Not a bad thing.. Glad I could help.

How far can you go with the stock receiver?

@OneManUnmanned

Жыл бұрын

Around 300 meters

I’ve watched this tutorial about 10 times. Followed it to a T. Tiny go still won’t bind to radio master zorro

@OneManUnmanned

2 жыл бұрын

I'll need more specific information to what your receiver is doing. Is it flashing or steady on? With your radio off does the receiver go into Wifi mode?

@nsmart5

Жыл бұрын

I have the same question with a Jumper T lite. The receiver has a steady light. I used a 470ohm pull down resistor. How would I know whether the Rx was in WiFi mode? Thanks, Nigel

Why isn't it called computer using computers to upgrade and flash drone parts. Andd upgrade to use and flash and upgrrade to use stuff that doesn't work ?

@OneManUnmanned

2 жыл бұрын

Things change so quickly in FPV that firmware updates are necessary new features.

Its funny how this quad almost looks like the new DJI fpv drone.

@OneManUnmanned

2 жыл бұрын

Very true... looks similar. I'm sure the DJI version will be larger though.

Sorry sound like you are from the Caribbean which island?

@OneManUnmanned

2 жыл бұрын

Yeh, good ear... From St.Croix. Are you from the Caribbean as well?

@wehttamak

2 жыл бұрын

Yea I am originally from St Vincent.... But I am living in Anguilla... B.W.I

@OneManUnmanned

2 жыл бұрын

I hear you..