Installing Copping metal flashing ,step by step Video!!
In this video I installed copping metal over a parapet wall , after installing the build up roof system , the copping was installed after stucco was done. hope you like it , please subscribe and share.
Eric.
Пікірлер: 88
For commercial, we always have welded corners. No top fasteners. Usually front cleat and rear neophrene screws. Preferred would be front and rear cleat. This job looks like a residential install, way down south in warm climates with no wind or uplift.
i like the cleat coping we use, we dont leave screws on top of the coping. i hate seeing screws on top of coping. nice cuts.
@cammccarthy686
Жыл бұрын
That's because you never put screws through the top it just invites water.
@anthonymacleod4493
10 ай бұрын
I’ve seen wind rip coping right off. We only top screw if we don’t have a locker for the coping and use grommet screws
Hey Eric thanks so much for your time and effort, nice job pretty well explain he look you can go Pro get one of those Go Pro cámaras and put on your head and you can use for run or bike and deduct on taxes .
Perfecto Garcia! Always a very professional job..you can be proud
@Garciasroofing
7 жыл бұрын
Thank you sir !!!
@peopleplaygrond1805
3 жыл бұрын
This is not professional it’s trash
Thank you very helpful
Looks clean
Great teaching.:-) :-) :-)
Gracias compa !!
Straight to point thank you , always wanted to know the proper way to install the coping metal around corners with the nice 45 cut
Gracias por el video aora ya soy metalero
Cool vid meng! Viva la messico!
perfect
You should do a 1" rib turn up at your outside/inside corners and overlaps. Flat seams leak!! Then cap ribs with a little cap and rivet it on! I repair coping cap that's done like this all the time that leaking!!
YeSir.u.The.Man...
Where to buy cover cap for parapet? Every roof store i call, they do not have it. I am in metropolitan area.
Nice Thanks Eric. Do you think 1 inch folds will be good enough in canada?
@cammccarthy686
Жыл бұрын
Standing seam your Corners DO NOT COPY this.
I've got so much to learn still. Ill stick to shingle roofing for now. Any advice for getting roofing jobs for a small company?
@SuperAceuno1
7 жыл бұрын
Anything and everything you learn can be applied to other applications, Reputation is everything for tradesmen, As long as you do a good job at a fair price you will get calls
@londonchristian1573
3 жыл бұрын
All metal to me is ears relief cuts and connect the points and make it look good fuck them shingles
How much is that metal coping you were using? An approximate...each piece? I need to buy some or order. Thanks for the video.
I always peel tge plastic where ever I lap metal to secure lol then when I am done i peel the rest so the metal doesn't get scratched haha. I just run a straight blade lightly and tear off the plastics.
I can instal the correct way with a continuous cleat like it should be done. I work in LA County. You need metal roofing I can also do the complete installation
@martintopete7164
4 жыл бұрын
Hi Milton I can use your services, contacta me. I live in Los Angeles area too.
Does anyone have any suggestions for terminating rolled roofing against a stone parapet with no regular horizontal joints? Over the top is not an option...
@Skeetr86
2 жыл бұрын
You'll need to use a drip edge and flashing combo. Hard to say without a visual.
@Skeetr86
2 жыл бұрын
Counter flashing before your roofing.
I need that coping where do i buy it and whats the price on it same color .
@Garciasroofing
6 жыл бұрын
Sam Campos ...any sheet metal company can fabricate it for you, before you order it, measure it, make sure you give at least 1" inch wider ,sometimes the wall are crooked so count that also.
Thak's for the vídeo gays
Donde puedo agarrar ese tipo de flashing
Why don't you invest in a tri-pod or a headmount? That is how you won't have to worry about thee filming part and have both hands to work efficiently.
@Garciasroofing
7 жыл бұрын
I'm not making a video for sale , that's the reason , the other way is if I start adding fancy stuff to my videos...I will take the original scent of it , when I film like that...you are looking thru my eyes... my videos are make to give everyone an idea of what is the basic of the roofing system. I could make a lot better videos but ...they will look to fancy like a studio made videos and people like to see something else. In that case go to the manufacturer's website and watch their professional videos on how to. greetings . Eric.
@stephens2850
4 жыл бұрын
Or get your mate to hold the camera
Tako su meni majstori napravili😢😢 bušenje lima horizontalno nije dobro. . .Morat ću to ponovo napraviti
Standing seam with clips hidden screws and drip clips
How long did it take you to do that whole roof ?
You could be proud 🤣 🤣😂🤣😂🤣😂
Hacks like this are the reason why sheet metal workers install this stuff here and not roofers.
@precisionink2736
5 жыл бұрын
Our roofing company has 3 metal roofing crews, 3 shingle crews and 3 membrane crews. I myself am a metal man. And yes....i do a lot of coping. You guys out there have never heard of a 3/8 hem at your joints, with driver? Standing seem on joints is extinct.
@Mr69Lazarus
4 жыл бұрын
precision ink please show us how you do it
@prometheustitan3858
3 жыл бұрын
This should of been done with one piece. Learn your 45° and laps
@cammccarthy686
Жыл бұрын
Yeah no kidding. Those Corners are gonna leak.
@caring-assoul_
9 ай бұрын
What’s so hacky about it? it’s functional. I doubt they would risk their license by doing a hacky job, as long as it passes inspection, that’s all that matters.
What about a hold down clear prior to installing the coping? Screws on top is not a great technique to use.
@vsavage9913
5 жыл бұрын
Why not screws on top milton?
@mrpartyshoes
4 жыл бұрын
Because if you screw on top that’s where the water will go. The purpose of a flashing is to shed water
@fredialvarado8738
4 жыл бұрын
Terrible craftsmanship. A continuos cleat should be installed prior
@manotas1960
4 жыл бұрын
@@fredialvarado8738 IS NOT CHICAGO OR OTHER WINDY AREAS
@patrickmansfield9488
4 жыл бұрын
@@manotas1960 terrible answer lazy actually
Yea I agree we use an S lock or standing seam that's pritty ugly hak job
As uno en español conmpa
Spring cleat S drives or butt plates Sealant Riveted corners Boom! You're done!
If you ever install coping like this on my job...I'll fire you on the spot..looks terrible, wheres the cleat? What's stopping the face and back from flapping
@manotas1960
4 жыл бұрын
ONLY ON WINDY AREAS BODY dont over kill
@patrickmansfield9488
4 жыл бұрын
@@manotas1960 always expect the wind buddy,only a fool would underestimate to power of the wind
@cammccarthy686
Жыл бұрын
@JAIME SANTA CRUZ it's a roof. Everywhere is fuxking windy at some point or other man. It's attitudes like yours that make a shit name for the trade. EVERY PEICE SHOULD HAVE MININUM A 40" CLIP IN THE MIDDLE
Where Is your wind clip? Why didn't you do a standing seam on your Corner. I've never seen a corner done like that and not leak.
Wouldn't the bolt penetrate the water proof layer, and rain leak into the parapet wall?
If i install coping like this here in canada i was fired instantly! Here we do the male and female and wrapping. We never use screw on top of the cap and we never install cap without a starter...
@cammccarthy686
Жыл бұрын
Yup same shit in bc. Standing seam with a clip wind clip on the face and If the parapet is above 6inches neoprene screw through the back or a clip in the middle. This is horrible work.
Don't install anymore please! Watch a u tube video on how to first.
As someone who makes coping/flashing, it really bugs me how lazily they handle the metal. Dragging that on a roof that is textured is like nails on a chalkboard.
This is a absolute hack job
@user-do2ie5kf2w
3 жыл бұрын
Where is your pro job video then?
@cammccarthy686
Жыл бұрын
@@user-do2ie5kf2w you know some people just do this job mon to fri 40+ hours a week. He doesn't have a standing seam corner which is an industry standard. You Never top screw through coping as water will sit their sometimes.
Yea this is a hack job.
Screws dont go on top
@vsavage9913
5 жыл бұрын
Why not screws on top xavi?
@waheedbhatti4305
5 жыл бұрын
@@vsavage9913 because the rubber seal will rot with time and water will start leaking from there. Additionally, the screws on top looks ugly.
@jesusborrego3270
5 жыл бұрын
@vsavage, you dont know?
Another HACK job!!
Screws on top.....reallly....
ewww get proper snips
Nup not good. Should be lacked. Will fail.
Real sheet metal workers make standing seam mitres. What’s this folding and raw edge shit 👎
@cammccarthy686
Жыл бұрын
Yeah.. screws through the top , doesn't safety hem his shit. Also he cut off the 1/2" kick on the first peice which you can use to hook onto the other back leg to hold it in place he's a roofer doing sheet metal
amateur job bad finishing