Installing C2Aero / Carter's Customs side skirts and rear splitters on 1999-2004 Mustang
0:00 Rear splitter and skirt extensions
0:51 What the rear diffuser looks like
1:32 Stuff needed, see description
2:17 How to install side skirt extensions
5:44 Skirts done
5:58 How to install rear splitters
13:06 Splitters done
13:22 Comparing skirts with splitters
13:38 All done, final check
Front splitter install & header panel reinforcement:
• C2Aero/Carter's Custom...
Other 'stang stuff • 1999 Ford Mustang
Adding rear splitters and side skirt extensions from C2 Aero/Carter's Customs to complement that brand's rear diffuser. May complete the kit by adding their front end splitter at a later time.
Install not too bad, little patience and careful measuring and you can get it whipped. The skirt extensions will come with pre-drilled holes, but the Rear splitters do not.
BEFORE MOUNTING EITHER PANEL - Find a way to mock the panels up before drilling holes, like with tape, and find where exactly you would like to mount these to fit the look of your car best. This is up to you and your personal taste, but there may be variables like the offset of your wheels that may dictate how far out you would like these to stick out, as both these panels allow for a degree of freedom as far as mounting.
Stuff needed
- stubby #2 philips screwdriver
- drill and bit
- masking or duct tape
- marker
- measuring tape
- fastener pry tool
Пікірлер: 18
I just put my set on yesterday. I’m so glad you made this video. It made the process so much easier. I took your advice and countersunk stainless steel screws in the rear splitters and it looks clean. Thank you so much for this video!
@sixgundave
Жыл бұрын
That's awesome 👌 makes my video making worth the effort. Yeah that guy makes some pretty sweet stuff
Just got my set in the mail last week, I was going to tackle it but I figured rather than curse out loud for the neighbors to hear I should see what issues exist instead! Thank you for showing us the way!
@sixgundave
Жыл бұрын
I appreciate you checking the video out. I included helpful info in the description as well - definitely mock these panels up before drilling any holes to make sure you have them where it works best on your particular car. Mine are where they are because I wanted them near my current wheel offset for instance. And supplied hardware is perfectly fine, I just did what I did due to personal preference.
Awesome Video 🤙🏽🔥
@sixgundave
Жыл бұрын
Thanks, I appreciate you watching 👍
Like the wheels, what brand?
@sixgundave
10 ай бұрын
Those are an SVE-brand model, called NVX. They look good in a bronze they come in too
🐺....🖤🌹
Hey look good with the side skirts Where those you buy it
@sixgundave
Жыл бұрын
The website is called c2aero.com. Out of North Carolina. They have complete ground effects setup, and some other custom made things.
@hugobonilla5810
Жыл бұрын
@@sixgundave cool man thanks 👍
@sixgundave
Жыл бұрын
@@hugobonilla5810 I appreciate you checking out the vid & the parts are great quality seriously. (No he doesn't sponsor me ha)
@hugobonilla5810
Жыл бұрын
Other cuestión man What lacks lug nuts you got on your rovos wheels
@sixgundave
Жыл бұрын
@@hugobonilla5810 The wheels are actually a Rovos knock-off from SVE. Since I use extended lug studs, I'm using open-ended, forged steel lug nuts from Gorilla.
Where did you get part between tail lights?
@sixgundave
Жыл бұрын
That whole thing is obsolete OEM from the Anniversary Edition '99 GT's. Three plastic panels that tape on. However one can round up replicas (at least last I knew) from the usual 'stang suspects, e.g. American Muscle, LMR, CJ Pony Parts. "Honeycomb decklid panel"