First one!!!

The fuel foam is designed to a) stop fuel sloshing around when braking/cornering and b) to stop a flame front propagating in the event of an accident and fire. Removing it is dangerous. You should use an e85/alcohol rated foam instead of removing it. Many of the racing regulations I've seen make fuel foam mandatory.

The foam is used to prevent fuel sloshing.

Very well made video. Super informative! Keep it up guys!

Briliant work guys you make a great team and a wealth of knowledge 👏 👍

Nice work. Doing this next week. Has the fuel line rubbed through the steel braids at the rear lower control arm yet?

How did you secure/mount the cell to the floorboard?

@Autosauce I know this is a older video but what size fuel cell are you using? seems like it fits well

What did you buy for the fuel cell for the rails and fitting sizes I need to run my lines a bit better and try to run a toggle switch for a push to start

What’s the link or brand to this fuel cell

Would using the top outlet as the return not cause bubbles in the tank or is that eliminated by the other vent? Also, how good is that fuel pump holding out to this day? I'm debating on ordering from the same brand but it's cheap so I'm skeptical

Helpful install. U guys should of used PTFE lines. No e85 for this car i take it?

What sending unit wire did you use that attached to that fitting and run it to the gauge?

I know this video is a year old but whar tipe of fittings are those and what size i got the same tank and dont know where to order the fittings .thanks

Great video

Yo I got the same fuel rail,how do you like it?

Bro you need to make a video of the wiring I bought the same pump and I can’t find a dam video of the wiring

what size fuel pump are you using

Where you get the return line from the regulator

Are the build need to meet certain rules? My 15 gallon ATL cell is about $1,500 alone and you need check or discriminator valve in case of roll over. The entire fuel cell especially for hatchbacks where these is no bulkhead to protect the driver in case of fire needs to build an metal enclosure to house the fuel related items.

Did ta use an 10 all the way to and from?

Parts list??

You want two large fuel filters. Radium is a great choice. 100 micron between the tank and fuel pump and install a 10 micron between the fuel pump and fuel injectors. This is proper build edicate. Not sure why the young man thought foam had anything to do with fuel filtering? Anyhow it is a good idea to remove the ebay foam however replace it with quality E85 tolorate foam. The foam is to prevent sloshing that eliminates your fuel system from sucking air.

Can you show us how you wired the fuel pump? Thats what im stuck on

@KiwiKarii

2 жыл бұрын

Facts

@lucidvtec

2 жыл бұрын

Use the stock fuel pump to trigger a hardwired relay to the external pump The hardwired relay should be powered straight to the battery..at least 12 wiring..10ga preferred

Good job

Is the red one a 15 gal ?

By chance can you lost a parts list? 40ft of -10 hose, in line pump, In line filter, cell.. but what about all the extra 45's and 90's. And such ..thanks

That i foam is to keep the fuel from sloshing around.

Where’s part 2??

Muy buen canal en comparacion ,Aqui hay material para los 100K plus subscribers...

Man what state u from

@Autosauce

2 жыл бұрын

Florida!

where did you source these parts? I cannot find them that cheap.. And nice job!

Where you based outta?

@Autosauce

2 жыл бұрын

Lakeland!

@CrestoAlex

2 жыл бұрын

@@Autosauce your a big inspiration brother keep it up

I don’t think running the lines threw the car is that dangerous because on the older Subarus they run down the inside of the driver side of the car

@Autosauce

Жыл бұрын

They are made out of a completely different material.

Second