Damn, I'm in the process of installing a thermostat and decided to check out a video prior just because. I never knew about that little vent hole. I've played with it with my finger but never knew it should be facing up.
@elchanojose
7 ай бұрын
Hello Scott! That component helps to get the air pockets out of the engine or as we call it burp air out. Also, this helps small amount of coolant to get by and always to have circulation through the cooling system and help or prevent static flow. Take well care Scott!
@terencescott3957
7 ай бұрын
@elchanojose4633 thanks for the info. I finished installing my new thermostat shortly after my last post. I went to check the positioning of the vent hole on my old thermostat. By luck I positioned it at the 11 o'clock position. Bit I'm good now. No leaks.
@sari-saritv.8235
4 ай бұрын
Thanks for this info
@jfcalix4 ай бұрын
The information what I was looking for thanks
@elchanojose
4 ай бұрын
Hello! Thank you for taking your time to watch our video and for sharing that this was what you were looking for. Take well care!!
@merchanthandson527119 күн бұрын
Thank you for very important info. Can i make small hole to it same size?
@mavadoroaster4 күн бұрын
Great info 👍
@elchanojose
4 күн бұрын
Hello! I’m Hank you for taking your time to watch our video and hope this was helpful. Take well care!
@durantplayz71119 сағат бұрын
My stant one doesnt have any hole im so confused
@TheShangralaaaa178 ай бұрын
the jiggle pin faces upwards so the air can escape
@user-bn7lp3go4lАй бұрын
Tab always goes to the top at its highest point 👍
@lorddraako1655Ай бұрын
I bought a thermostat from AutoZone and it doesn’t have the jiggler pin should I install it?
@Carpenter_King864 ай бұрын
Thanks homie
@midwest_nikk26829 ай бұрын
It does that no matter where the thermostat is located.
@SimonLopez33123 ай бұрын
Hell yeah Brodie
@luisematos_5 ай бұрын
Great! 👍🏻
@elchanojose
5 ай бұрын
Hello! Thank you for taking your time to watch our video and for sharing that it was great and you liked as well. Take well care!
@chavatoyz641611 ай бұрын
That’s why I have a problem with my truck 😡 I installed it the wrong way!
@Thelost909
8 ай бұрын
I just redid it on my jeep to find out I did it wrong to 😂
@TaylorRamirez-uz9fw10 ай бұрын
Pregunta. El Ac De mi carro no está funcionando Sale caliente el aire y tiene coolant y el fan no está running
@Travis-bs6hm8 ай бұрын
Thank you for your post
@mindofmantae82888 ай бұрын
Thank you
@CaratLV6 ай бұрын
i just bought a thermostat for my jeep compass but it didnt come with that silver piece in the hole???
@elchanojose
5 ай бұрын
Hello! Some thermostats are not made the same. Some are made different but still work. The only advantage of that little silver valve is to allow air trapped to move by when the thermostat is close. This helps the engine to burp air out and fill the space with coolant. Take well care!
@waltersmith31658 ай бұрын
Real mvp
@kenstole46013 күн бұрын
It called as jiggle pin
@elchanojose
2 күн бұрын
Hello! Thank you for sharing what it is called! Take well care!
@anthonytrejo665 ай бұрын
So the little metal thing has to be open?
@elchanojose
5 ай бұрын
Hello! The metal does not have to be open, it would be good and helpful to sit at the highest point when installation. Also, keep in mind that the thermostat be installed in the right way for it to operate properly. Take well care!
@user-lr6ks3xn6r4 ай бұрын
Tha k you for explaining the little thing that can be a fatal mistake
@DFWAuto_Hack Жыл бұрын
Someone told me to break this off so my car does not overheat even if thermostat gets stuck closed. It was true. Car wants to overheat but cannot
@kevinhancock4064
11 ай бұрын
May I ask how you know it wants to overheat ? Ty
@Dcdc956
11 ай бұрын
Don’t do this… 🤦♂️🤦♂️🤦♂️🤦♂️🤦♂️ Jesus…
@DFWAuto_Hack
11 ай бұрын
@@Dcdc956 lol i did and it worked
@AbelG8781
11 ай бұрын
@@Dcdc956only a dumb mfr would do something like that SMH
@OtherDalfite
10 ай бұрын
@@Dcdc956all it does is bleed a bit of fluid over constantly. Not the end of the world
@elroco4827Ай бұрын
It should be 12:00. The jiggle pin also helps bleed the vehicle
@sergiocalderon54169 ай бұрын
Thank you dude I just changed mine a while ago🙏🏽
@elchanojose
9 ай бұрын
Hello Sergio! Thank you for taking our video and hope this info is helpful for your next replacement. Take well care Sergio!
@donaldwhiteman32245 ай бұрын
could this cause overheating? if installed with jiggle pin facing downward?
@towcars5550
4 ай бұрын
I think so I'm waiting on mine I bought one from AutoZone didn't have that lil jiggle...I got one from Amazon and it has it
@donaldwhiteman3224
4 ай бұрын
it was the cause of my overheating along with the coolant temp sensor. replaced no problems now! @@towcars5550
@89gt5.02 күн бұрын
In short it’s a bypass.
@elchanojose
21 сағат бұрын
Hello! Yes, to let the air go by and keep fluid flowing. Take well care!
@Codeineworld2 ай бұрын
I need help from you
@MiguelOrtiz-kl1yb11 ай бұрын
Is it hard to install one ?? Just asking cuz I took mine to the shop and it’s been 2 days 😅😅
@elchanojose
11 ай бұрын
Hello Miguel! A thermostat is not that hard to replace. Some cars require more labor than other but 2 or 3 days is too much time for this kind of job. The reason on why your car is taking too long for a thermostat replacement, is probably because the shop has other cars that are being worked on and your car is sitting there until a spot is available. Take well care Miguel!
@M.Qambar
11 ай бұрын
It takes 2-3 hours at most if you don't know what you're doing
@gta4162
11 ай бұрын
@@M.Qambarbro. It takes like 20 minutes or less to replace a thermostat. On this type of car.
@M.Qambar
11 ай бұрын
@gta4162 Yeah, that's true for me and you, but the original comment obviously doesn't know much about cars so it'll take them longer + i was talking about cars in general not just about this one because some would need a lot more work just to change a thermostat
@elroco4827
Ай бұрын
It’s super easy. If you have the funds to pay the shop and you don’t feel like fooling with, then take it to the shop. But if you want to save money, do it yourself. I do a lot of maintenance myself. I’ve learned a lot by watching many KZread videos.
@user-xh2jz6jc4q Жыл бұрын
I don't understand how you can install it the wrong way. You can't install upside down, only a 180 maybe
@KKDriver
Жыл бұрын
The thermostat I replaced on my civic literally wouldn’t fit unless the release tab was at the top. Pretty smart engineering.
@Caleb-lbj11 ай бұрын
I drill it out sorry don't need it can drives better and faster
@elchanojose
11 ай бұрын
Hello! There is nothing wrong about drilling it out. Makes sense on having a small hole to let small amount of liquid to go by. I don’t know about making it go faster but everything can be posible. Take well care!
@samgrieg2542
7 ай бұрын
yeah that mod alone adds like 10hp to the wheel
@alejaz84038 ай бұрын
Does it matter which way you Install it?
@wbforsure2104
5 ай бұрын
It does matter. The side with the coil spring always faces into the motor. If you install it backwards it will overheat
@elroco4827
Ай бұрын
Probably not but I’d install it with the jiggly point facing upwards at 12:00
Пікірлер: 76
Information gained 💯 thanks!!
Damn, I'm in the process of installing a thermostat and decided to check out a video prior just because. I never knew about that little vent hole. I've played with it with my finger but never knew it should be facing up.
@elchanojose
7 ай бұрын
Hello Scott! That component helps to get the air pockets out of the engine or as we call it burp air out. Also, this helps small amount of coolant to get by and always to have circulation through the cooling system and help or prevent static flow. Take well care Scott!
@terencescott3957
7 ай бұрын
@elchanojose4633 thanks for the info. I finished installing my new thermostat shortly after my last post. I went to check the positioning of the vent hole on my old thermostat. By luck I positioned it at the 11 o'clock position. Bit I'm good now. No leaks.
@sari-saritv.8235
4 ай бұрын
Thanks for this info
The information what I was looking for thanks
@elchanojose
4 ай бұрын
Hello! Thank you for taking your time to watch our video and for sharing that this was what you were looking for. Take well care!!
Thank you for very important info. Can i make small hole to it same size?
Great info 👍
@elchanojose
4 күн бұрын
Hello! I’m Hank you for taking your time to watch our video and hope this was helpful. Take well care!
My stant one doesnt have any hole im so confused
the jiggle pin faces upwards so the air can escape
Tab always goes to the top at its highest point 👍
I bought a thermostat from AutoZone and it doesn’t have the jiggler pin should I install it?
Thanks homie
It does that no matter where the thermostat is located.
Hell yeah Brodie
Great! 👍🏻
@elchanojose
5 ай бұрын
Hello! Thank you for taking your time to watch our video and for sharing that it was great and you liked as well. Take well care!
That’s why I have a problem with my truck 😡 I installed it the wrong way!
@Thelost909
8 ай бұрын
I just redid it on my jeep to find out I did it wrong to 😂
Pregunta. El Ac De mi carro no está funcionando Sale caliente el aire y tiene coolant y el fan no está running
Thank you for your post
Thank you
i just bought a thermostat for my jeep compass but it didnt come with that silver piece in the hole???
@elchanojose
5 ай бұрын
Hello! Some thermostats are not made the same. Some are made different but still work. The only advantage of that little silver valve is to allow air trapped to move by when the thermostat is close. This helps the engine to burp air out and fill the space with coolant. Take well care!
Real mvp
It called as jiggle pin
@elchanojose
2 күн бұрын
Hello! Thank you for sharing what it is called! Take well care!
So the little metal thing has to be open?
@elchanojose
5 ай бұрын
Hello! The metal does not have to be open, it would be good and helpful to sit at the highest point when installation. Also, keep in mind that the thermostat be installed in the right way for it to operate properly. Take well care!
Tha k you for explaining the little thing that can be a fatal mistake
Someone told me to break this off so my car does not overheat even if thermostat gets stuck closed. It was true. Car wants to overheat but cannot
@kevinhancock4064
11 ай бұрын
May I ask how you know it wants to overheat ? Ty
@Dcdc956
11 ай бұрын
Don’t do this… 🤦♂️🤦♂️🤦♂️🤦♂️🤦♂️ Jesus…
@DFWAuto_Hack
11 ай бұрын
@@Dcdc956 lol i did and it worked
@AbelG8781
11 ай бұрын
@@Dcdc956only a dumb mfr would do something like that SMH
@OtherDalfite
10 ай бұрын
@@Dcdc956all it does is bleed a bit of fluid over constantly. Not the end of the world
It should be 12:00. The jiggle pin also helps bleed the vehicle
Thank you dude I just changed mine a while ago🙏🏽
@elchanojose
9 ай бұрын
Hello Sergio! Thank you for taking our video and hope this info is helpful for your next replacement. Take well care Sergio!
could this cause overheating? if installed with jiggle pin facing downward?
@towcars5550
4 ай бұрын
I think so I'm waiting on mine I bought one from AutoZone didn't have that lil jiggle...I got one from Amazon and it has it
@donaldwhiteman3224
4 ай бұрын
it was the cause of my overheating along with the coolant temp sensor. replaced no problems now! @@towcars5550
In short it’s a bypass.
@elchanojose
21 сағат бұрын
Hello! Yes, to let the air go by and keep fluid flowing. Take well care!
I need help from you
Is it hard to install one ?? Just asking cuz I took mine to the shop and it’s been 2 days 😅😅
@elchanojose
11 ай бұрын
Hello Miguel! A thermostat is not that hard to replace. Some cars require more labor than other but 2 or 3 days is too much time for this kind of job. The reason on why your car is taking too long for a thermostat replacement, is probably because the shop has other cars that are being worked on and your car is sitting there until a spot is available. Take well care Miguel!
@M.Qambar
11 ай бұрын
It takes 2-3 hours at most if you don't know what you're doing
@gta4162
11 ай бұрын
@@M.Qambarbro. It takes like 20 minutes or less to replace a thermostat. On this type of car.
@M.Qambar
11 ай бұрын
@gta4162 Yeah, that's true for me and you, but the original comment obviously doesn't know much about cars so it'll take them longer + i was talking about cars in general not just about this one because some would need a lot more work just to change a thermostat
@elroco4827
Ай бұрын
It’s super easy. If you have the funds to pay the shop and you don’t feel like fooling with, then take it to the shop. But if you want to save money, do it yourself. I do a lot of maintenance myself. I’ve learned a lot by watching many KZread videos.
I don't understand how you can install it the wrong way. You can't install upside down, only a 180 maybe
@KKDriver
Жыл бұрын
The thermostat I replaced on my civic literally wouldn’t fit unless the release tab was at the top. Pretty smart engineering.
I drill it out sorry don't need it can drives better and faster
@elchanojose
11 ай бұрын
Hello! There is nothing wrong about drilling it out. Makes sense on having a small hole to let small amount of liquid to go by. I don’t know about making it go faster but everything can be posible. Take well care!
@samgrieg2542
7 ай бұрын
yeah that mod alone adds like 10hp to the wheel
Does it matter which way you Install it?
@wbforsure2104
5 ай бұрын
It does matter. The side with the coil spring always faces into the motor. If you install it backwards it will overheat
@elroco4827
Ай бұрын
Probably not but I’d install it with the jiggly point facing upwards at 12:00