Installing A Big Brake Kit On A Minibike! Motovox Mb80
Автокөліктер мен көлік құралдары
Hope you enjoyed!
Minibike brake install video here • How To Install Hydraul...
How to bleed minibike brakes here • HOW TO-Fill Up And Ble...
********Disclaimer********
Please do not try to re-enact or recreate anything you see in these videos.
Guido does not take any responsibility for injuries or equipment failure created by doing so.
ALL GUIDO CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.
#minibike #motovox #predator212 #minibikefast #diyminibike #howto
Пікірлер: 44
Make sure to like and subscribe!!!
@jaybird0000000
3 ай бұрын
what happened to this bike 7 months ago wheres the motor and it completed >>>>>?
nice setup🤝 im tryna get something like this
Nice rides bro I’m just getting into Mini bikes and got a mega moto 105 of offer up for $150. Just gotta get it to idle and I’m set
@Guido19
10 ай бұрын
Heck yeah!
Ah the last part was what I needed … so I did the same and have the same bike and breaks .. but where u hit the breaks I have to squeeze it fully to break and it’s not that hard when I do it .. I can still slide cuz it’s not so tight .. any advice
Where did you get that seat from-I’m building a similar bike and like that seat
@Guido19
3 ай бұрын
It’s the stock one I took it and got it reupholstered
thx for the video and info - what hardware was needed like size of bolts etc?? im about to do this tab extension and brake install myself as well
@Guido19
8 ай бұрын
I wish I could tell you but I don’t know the exact hardware. Also the holes on the tabs be be different from other ones so different sizes may be needed also there could be different threads on different brake setups as well.
@NouriGains
8 ай бұрын
you got the hardware from mini bike larry as well? what welder did you use for welding the tabs? sorry for the million questions lol@@Guido19
@Guido19
8 ай бұрын
@@NouriGains your good! No I got my bolts from a hardware store. I welded it myself
What size rear disc are you running? I want to get those stretch tabs with the GPS 10” wheels and they run a 8.6” disc.
@Guido19
3 ай бұрын
Im running the standard 7.06in motovox rotor.
@Guido19
3 ай бұрын
You could run a bigger rotor you will just have to make a custom mount for the brake cause the rotor is bigger
Larry tabs 💪🤘🤘
My brake pads falling off when I took out the plastic that comes in between the brake pads help?
@Guido19
2 ай бұрын
When the rotor is installed it should be fine if not you might need to get a thicker rotor
@warzone7571
2 ай бұрын
@@Guido19 I figured that out
what happened to this bike 7 months ago wheres the motor and it completed >>>>>?
@Guido19
2 ай бұрын
This project got pushed to the side lol. Kinda lost interest in but looking to start it up again soon!
@takemopenn
Ай бұрын
Wanna sell it
Any suggestion or help ? My brake pads keep on falling off
@Guido19
3 ай бұрын
You may need a thicker rotor! They sell thicker rotors for that issue or if it’s getting too hot a thicker one will dissipate heat better too
@ghostcutz5845
3 ай бұрын
@@Guido19i had that same exact question i got the same rotor as you and big brake for the stretch but the pad just keeps falling out i ordered another one diff brand to see if it was just bad but its the same thing
@Guido19
3 ай бұрын
@@ghostcutz5845 mine is good and mine don’t fall out but if it’s you need a aftermarket one that is thicker
@Mplvv
2 ай бұрын
@@ghostcutz5845 I found the issue I had to just get it aligned right and the little thing that’s holding the brakes in I pushed it in for the breaks won’t fall off
I'm trying to install this setup on my mm80 but the piston on the caliper will not retract and just keeps pushing on the rotor
@Guido19
3 ай бұрын
You can push it back in with a screwdriver!
Where do you get the spacers for the brakes?
@Guido19
8 ай бұрын
I got them from a hardware store
Nice bro... send a link for that fisc brake setup
@Guido19
10 ай бұрын
www.amazon.com/Hydraulic-Cylinder-50cc-90cc-125cc/dp/B0C52B7VWY/ref=mp_s_a_1_3?crid=395LXQFWCR61Z&keywords=mini+bike+hydraulic+brake&qid=1695828932&sprefix=minib%2Caps%2C1093&sr=8-3
@NouriGains
8 ай бұрын
thx @@Guido19
where did u learn to work on mbs?
@Guido19
10 ай бұрын
Self taught! Bought it and messed around and learned!👍🏼
Where did ur front rim come from or off of?
@Guido19
10 ай бұрын
Got it in a trade!
are the brakes still holding up?
@Guido19
9 ай бұрын
Yeah they are great!
What is the rear rim and tire?
@Guido19
7 ай бұрын
It’s a 6in mag wheel from gopowersports and a 13in slick
Another Great Video NePHeW!!! You’re build L👀K’s AMAZING! - #MiNiBiKeLaRRy! 🤜❤️🤛🫡🎁🤘
@Guido19
10 ай бұрын
Aye I appreciate it homeboy!!!!!!