Very nice

do you have a casting deeper in your boat? if so, how do you deal with that antenna? what is the range?

@RobertZovko

4 ай бұрын

kzread.infoQCY1eNhAXGU?feature=share I fish at a maximum of 120 meters, so I tested it up to 150-160 meters and it works without problems, I didn't go further, but I believe it works at longer distances as well

Great video! I have learnt so much from your channel! I have installed the new equipment but I have a problem. Everything works as it should except I have no lights. Everything is connected as it should be. Do you have any ideas on how to solve or test the issue? Thanks for your time.

@RobertZovko

2 ай бұрын

on the LED light connector, replace plus and minus (on this board they are reversed)

@fishing_on_a_shoe_string

2 ай бұрын

Thank you for your quick response. I'll give it a go.

Hello, I bought the TXG4-RX40G set and I don't know how to replace the GPS module? I thought I could just plug it in and it would work, but unfortunately it doesn't work, I don't know how to replace these modules, I probably need to re-solder something, could you post instructions on how to do it?

@RobertZovko

3 ай бұрын

You do not need to change the GPS module.

@sawomirjagieo4871

3 ай бұрын

but how to do it? Could you write a small instruction?@@RobertZovko

@sawomirjagieo4871

3 ай бұрын

Does the GPS module need to be configured before installation or is it enough to connect it correctly?@@RobertZovko

@RobertZovko

3 ай бұрын

I put the BK-280 and it doesn't need to be adjusted, I haven't tried other modules. baud rate: 9600 protocol: NMEA update rate: 5 Hz default 1 Hz SBAS on

@sawomirjagieo4871

3 ай бұрын

OK thank you@@RobertZovko

I also have a problem. I have a problem with the magnetic field norm H (20 -70 ), I have 120 uT, I tried everything but it doesn't decrease. Can you give me some advice?

@RobertZovko

4 ай бұрын

you need to move the motherboard away from the magnet, for example the motor... to be sure, try everything before installation, if you still have too high readings, then the fault is on the motherboard

@pauliusberzinskas1810

4 ай бұрын

I have one more problem. Maybe you had it too. after calibrating everything and setting the function to go home on autopilot, the ship will sail in the other direction and not to the point?

@pauliusberzinskas1810

4 ай бұрын

should the arrow on the motherboard point to the front of the boat? and the gps module pointer to the main board? because the autopilot works the other way around??

@RobertZovko

4 ай бұрын

Yes, the arrow points towards the front of the feeding boat. The GPS module is mounted on the motherboard and the module goes up, looking at the sky.

Have list what need buying all electronics ?

@RobertZovko

4 ай бұрын

if you are changing the existing electronics, then you only need the TXG4-RXG3 kit (it has everything: remote control, motherboard with GPS module, motor cables, antenna)

Hi, i ordered a v020 bait boat, do you think it is worth buying this kit to upgrade? Thank you

@RobertZovko

3 ай бұрын

If you do not need one-handed control, there is no need to change the electronics while it is working.

@Antonio-tv1lv

3 ай бұрын

@@RobertZovko Ah ok thanks, I don't need the one-handed controller but I would like to increase the precision of the GPS, given that many complain about poor GPS precision in these boats. Do you know if it is possible to increase the precision by perhaps just changing the GPS module with a more precise one? Do you have any to recommend? Thank you.

@RobertZovko

3 ай бұрын

@@Antonio-tv1lv kzread.info/dash/bejne/dI2kuMivhMuWgs4.htmlsi=OOkzNWgXB0xNUWie

@Antonio-tv1lv

3 ай бұрын

@@RobertZovko oh perfect thank you

@muratfisherman9769

2 ай бұрын

Where does the GPS module connect? on motherboard please 🙏

I need your help, I have a question about the GPS module

@RobertZovko

4 ай бұрын

how can I help you?

@marcello7509

4 ай бұрын

Thank you for writing, can we do it in private?

@RobertZovko

4 ай бұрын

robert.zovko@gmail.com@@marcello7509

@marcello7509

4 ай бұрын

​@@RobertZovkook, I sent the message, thank you!

How to do it to the motherboard in the video. I have it too

@RobertZovko

2 ай бұрын

from the motherboard, vcc goes to vcc of the GPS module, then GND goes to GND, TX goes to RX, RX goes to TX. You can find the module settings in my answers to others.

@muratfisherman9769

2 ай бұрын

Thank you very much

Имам лодка boatman actor2021 възможно ли е да се монтира такова управление

@RobertZovko

10 сағат бұрын

I don't know what engine is in them. According to the manufacturer's recommendation, it supports max 10A and 12V. These data are the ultimate limit at 12V current is about 8A. Most likely, coolers should be added to the drivers.

why did you change the gps module, you can tell me more?

@RobertZovko

4 ай бұрын

I replaced the existing GPS module because the original one is of the M6 series, and I put the M9, which is more precise (

@Dicibel

21 күн бұрын

@@RobertZovko Where did you order the GPS module? Link please?

@RobertZovko

21 күн бұрын

​@@Dicibelwww.aliexpress.com/item/33030159409.html?spm=a2g0o.detail.pcDetailBottomMoreOtherSeller.3.7c6fO535O535pw&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40050.354490.0&scm_id=1007.40050.354490.0&scm-url=1007.40050.354490.0&pvid=f62a2132-3e70-4559-bbff-384cf37f8c46&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40050.354490.0,pvid:f62a2132-3e70-4559-bbff-384cf37f8c46,tpp_buckets:668%232846%238111%231996&isseo=y&pdp_npi=4%40dis%21EUR%2110.87%218.70%21%21%2111.40%219.12%21%40211b600c17200067983308463e1b9d%2112000033295023263%21rec%21HR%21169046750%21&utparam-url=scene%3ApcDetailBottomMoreOtherSeller%7Cquery_from%3A

@Dicibel

21 күн бұрын

@@RobertZovko the link is not working

@RobertZovko

21 күн бұрын

@@Dicibel www.aliexpress.com/item/1005004405692761.html?spm=a2g0o.order_list.order_list_main.110.5ae61802fELoWf

Поменял тоже модуль gps и пропала связь между платой и пультом. Что может быть?

@RobertZovko

Күн бұрын

It depends on which module you put in and which motherboard it is. For some models, only their modules can be used.

@Dicibel

10 сағат бұрын

​@@RobertZovko а как привязать пульт к материнской плате по новой?

@RobertZovko

10 сағат бұрын

@@Dicibel which remote is it?

@Dicibel

10 сағат бұрын

​@@RobertZovko пульт как у вас в видео(TXG4) . Хочу сопоставить код по новой как это сделать