Install solid tire on a scooter. Xiaomi or similar models.
Жүктеу.....
Пікірлер: 187
@Nathanael.Thomas3 жыл бұрын
This is the fastest tire installation I've seen so far and I've been searching a lot.
@radamante3231
2 жыл бұрын
Of course he is a mechanics with all tools available
@marsmellow1589
2 жыл бұрын
Put the rim on two pieces of thick wood, heat up the tyre in hot water and with three tyre levers and two persons its quite easy as well.
@kevin_ramirez2529
2 жыл бұрын
@@radamante3231 yea I don’t have a workbench with a vise, wish I did it’ll make it a whole lot easier
@bobl93182 жыл бұрын
Thanks this finally worked for me. For those people who don't have a vice or cable ties like me, I just used by body weight and put my knee on the tire to hold it in place while I used the levers to pull the top part of the tyre over the rim.
@takerumaeda14773 жыл бұрын
I tried getting a local bike shop in Portland to view this video and have my Xiaomi tubeless tire fitted onto my Gotrax XR Ultra rear wheel rim but they were too afraid to commit to this. So I took it upon myself. I gathered some very little supplies from the local hardware store; a 5 gallon bucket, 11 inch zip ties, and a 12 inch bar clamp. The workers at the ACE hardware shop didn't quite know themselves on how to tackle the installation but they agreed that my set-up was sound. Fast forward, I warmed up two pots of water to just under 200 deg F and let the tire soak for 10 minutes. You need just enough water to fully submerge the tire. I had with me two big tire irons from a previous purchase and a can of WD 40 just in case i needed lubricant. Guess what, folks. All it took was ONE zip tie and two of three tire irons I own and the tire went onto the rim in less than one minute. I kid you not, it's fucking doable and I have little to no experience with bike/scooter maintenance (although I have experience as a maintenance worker). 5 Gallon bucket of 200 deg F water (soak for 10 minutes -- THIS IS CRITICAL AND WILL SAVE YOU TIME AND ENERGY) One zip tie (I didn't even need the damn Bar Clamp) Two tire irons (not sure if you can get away with just one) Whole prep and execution done in less than 15 min. Thank you for this video. I've seen countless others and this was by far the most efficient process. I was worried I'd need a table mounted clamp like in this video but I did this on my kitchen floor. For safety reasons, just don't heat the tire in an oven or microwave or have it inside one of your pots. Get a bucket and wear some work gloves while you're at it.
@bob-ny6kn
3 жыл бұрын
I found that placing the tire/rim into a vice and one crowbar (tire iron) was enough. The heated water or soap/cleaner/wd40 was not necessary.
@itsmesezgin
2 жыл бұрын
how can you do it with the wheel where there is no entry with the zip tie, for some the wheel is the front and others its the rear.
@cjever193 жыл бұрын
This is the best advice on how to install one. Once I saw this, done in 3 minutes, like this man. Well done.
@ZeffyZ3 жыл бұрын
Thanks, locking a point with a strap was the key for me. However, I didn't use WD40 inside for fear the tyre would slip while breaking, just dishwashing soap on the bead. I also used the old tyre as base to work on to keep everything flat.
@terencemckenna96302 жыл бұрын
Just did this last night worked for both front and back tire, only took me 20min each tire, thank you very much!
@occasional-rebel4 жыл бұрын
This is the best tutorial hands down. Others make it look like a nightmare, which is not true at all. The microwave thing and lack of proper tools in other videos will put anyone on a wrong track, where nightmares (and even possible trauma) are to be had.
@wingovertd2 жыл бұрын
Definitely the best video. Very effective and short video, no small talk, the best!
@michalmikilo3 жыл бұрын
This was the only tutorial that helped, thanks!:)
@dakarak2 жыл бұрын
Legend. The trick of chucking it in a vice is the way to go, I didn't have the right tools - but a couple of large flat headed screwdrivers did the trick. Cheers
@cooljw Жыл бұрын
Thank you for showing the method! It worked well for me. Tips: make sure you heat the tire - microwave is fine, use liquid soap or oil as lubrication - also on your tire levers, think of the process as snapping a big thick rubber band onto the rim. Stretch that tire to get it over the rim and don't be shy, you're not going to break the tire. Next up: I try to do the front tire without a vise.
@codywright8510
10 ай бұрын
I broke the tyre
@glennsheridan90413 жыл бұрын
You legend mate I thought this was impossible took me 5 mins following this 🔥🔥
@timwieser5154 Жыл бұрын
oh my gosh you are a genius - the idea of using zip ties saved the day, thank you so much!
@kevinbridges92803 жыл бұрын
Awesome video. Couldn’t have done it without you. Thanks
@ThiagoRavanhani2 жыл бұрын
The best video, i tried a lot of others ways and fail. First time i tryed yours, and Done. Thanks from Brazil.
@mattkkma Жыл бұрын
Excellent. Your method worked like a charm. Thanks!
@Jamiedoh7893 жыл бұрын
Wow worked great on the rear tire of my Gotrax Elite! Thirty seconds and POP!. Small centering time and done. i do have have to say though. Tried this on my front tire with the hub motor in and had to muscle it the old fashioned way. Not the vice method. Front tire wheel and tire wouldn't stay in the vice for the life of me. Kept popping out. Perhaps removing the hub motor might have made it easier but i doubt it.
@Adrian-gx4ru2 жыл бұрын
Thanks I nearly burst into tears on this job . Great solve!
@joem601010 күн бұрын
I struggled using the vise, but found that zip ties worked great and made it pretty easy. I just used soapy water for lubricant and that worked fine.
@ivansmiljanic3274 жыл бұрын
Worked like a charm!
@j4nv2 жыл бұрын
I learned something, thank you. Though I would put aluminium brackets between the rim and the vice, to avoid damage or bending on the rim.
@monkeyman82653 жыл бұрын
Extremely helpful video thanks. I had a buddy that was pulling his hair out trying to install the thing.
@MrRivii3 жыл бұрын
cool, it is useful to have vice and proper tools for putting on a tire. Since at home you are not going to have vice, ziper method is also fine, and takes only couple minutes.
@machinis10 ай бұрын
To the haters in the comment section: 1. I took my daughter's scooter to 5 different bike shops in FL. They all refused to fix it. Being mechanically inclined, I chose to fix it myself. 2. I used silicone grease instead of WD-40. 3. The vise is a must! I tried pressing without it, and it was a nightmare. Thank you for this video!!
@Claude11003 жыл бұрын
Thank you for posting very helpful I pray I never have to remove it .. !!
@ilexcorp4 жыл бұрын
I like the way how he lubricates
@Vangeliss3 жыл бұрын
Thank you, this was helpful
@Jazztmpt2 жыл бұрын
This video just saved me a bunch of time, and I appreciate it! It worked like a charm on the rear wheel of my macwheel mx-1. Unfortunately, I had no luck with the front wheel on the motor, as it kept popping out of the vice. Do you have any suggestions on how to do the front wheel?
@DenisBikeMechanic
2 жыл бұрын
Thanks. Probably you need a wider vise.
@itsmesezgin
2 жыл бұрын
@@DenisBikeMechanic a wider vise? Like what? I have the same problem, there is no way to zip tie one of the wheels where there is no entry
@piokul11 ай бұрын
Very helpful, thank you!
@1jfmproductions3 жыл бұрын
Good Job...my favourite video...
@abloslimshady3 жыл бұрын
Oh I have too really thank you, it’s like two out I was trying too feet my new solid tire but I cannot 😅, now I’m boiling water to put my solid tire inside 😂
@MikeCaskings3 жыл бұрын
Hi I've got a kugoo s1 and is it a easy process to change from plastic to rubber and can you show me how to do it please thanks.
@blastardinc2 жыл бұрын
BEST VIDEO GOING ON THIS PROCESS!
@larryhullinger15062 жыл бұрын
You made that look so simple Gona get solid tires for my gotrax
@DenisBikeMechanic
2 жыл бұрын
Thanks. Vice is a key point here.
@itsmesezgin
2 жыл бұрын
@@DenisBikeMechanic can you recommand a home-vice? The way you have looks way to big to be in my room.
@jonj22973 жыл бұрын
Bet that vice scratched that rim up nice
@mouhamedsidibe9728 Жыл бұрын
Is the Xiaomi Mijia M365 8.5inch compatible with the gotrax gxl v2 tire
@w7y3a2t6t15 ай бұрын
I have a Neon Pro Okai scooterr model ES30 and the back tire got badly damaged, so i want to find a decent replacement compatible for it and put 2 new tires to my scooter, im new at this type of stuff and i don't understand very much about tires sizes and comparability The tire says 60/75 - 6.5 (10×2.5) And its hard to find on amazon or ebay and how to look for one that fits And i need my scooter to be able to go to work and back or i would have to walk every day around an 1hour some tes more since i gotta do a lot of heavy lifting at work and my body takes a lot of damage.
@mr.z31613 ай бұрын
Does this fit for a Segway F-30 that has inner tube ? Or can I use a tubeless tire. If yes. What kind can I use.
@dave94562 жыл бұрын
I need a vice Good job buddy 👍👍
@DenisBikeMechanic
2 жыл бұрын
Thanks!
@eminozdemir75433 жыл бұрын
Hover 1 Alpha electric scooter Tire and inner tube ??? Solid tire ??? I can't able to find it anywhere any ideas please let me know
@89GTFoxDude2 ай бұрын
Mine came with solid rubber tires (HiBoy S2 Pro) and they are rock hard with hardly any flex at all. I'd like to replace them with honeycomb tires but they look like a pain to remove 😩.
@luisangeltanimontoya32292 жыл бұрын
hi mister, can i buy them red in 8p and adapt them to my xprit 10p scooter?
@OO-eh6mi3 жыл бұрын
О, наш человек! Наш человек всегда профессионал! Спасибо за видео ;-)
@DenisBikeMechanic
3 жыл бұрын
Спасибо за коммент!
@MrMaybe89
Жыл бұрын
@@DenisBikeMechanic Dobrii denj. Estj vopros. Etji koleso bez vozduha ne ochen horoshie? Govorjat shto tjazhelo katatsa.
@DenisBikeMechanic
Жыл бұрын
@@MrMaybe89 зимой дубеют, летом норм. В целом solid tires лучше чем постоянно латать надувные.
@MrMaybe89
Жыл бұрын
@@DenisBikeMechanic Spasibo za otvet. Nu zimoi ja vobsje nje jedu. No mnje znakomii govoril shto s Solid Tyres ochen tjazhelo, koleso kak kamnji. Tjipa bjotsa ochen kogda jedish.
@DenisBikeMechanic
Жыл бұрын
Поставь русскую Клаву. Глаза сломать можно ;) На мой скутер я бы поставил solid tires и не парился бы. Они жёстче но практичнее.
@ferrari4sale5632 жыл бұрын
It's looks so easy. I'm planning to get a solid tire scooter.
@B3D2 жыл бұрын
may I know how this tire perform ? is that better ? I wondering should I put on my mten3 ...
@DenisBikeMechanic
2 жыл бұрын
It's about the same. I don't see much difference when ride it.
@danielday1345 Жыл бұрын
I don't use E scooters myself but done a couple of scooters for my work colleagues the way I done it was to use a vice a weak solution of washing up liquid a utility bar didn't heat the tires still had them on in seconds
@jojjan934 жыл бұрын
Nice, will try this
@jojjan93
3 жыл бұрын
@OG Loc i won't. I threw the scooter away
@jmo560410 ай бұрын
How often will live that solid tire? 1 year?
@joebriggs95993 жыл бұрын
Thank you.
@larryc1616 Жыл бұрын
For me it's just easier to pay a bike shop and never use air filled tires again.
@itsmesezgin2 жыл бұрын
how can you do it with the wheel where there is no entry with the zip tie, for some the wheel is the front and others its the rear.
@ThegreatNomadicadventure3 жыл бұрын
solid tyres are hell for city streets such a rough ride
@adamcare
3 жыл бұрын
no air tires are, because they go flat!
@robzillagarage Жыл бұрын
Are there benefits to this over a inner tube tire
@albertgutierrez7036
Жыл бұрын
With a solid tire you’ll never need to add any air ever just grab and go not really recommend this for stronger scooters these wheels work better on entry to mid level escooters.
@mrfloorguyz3 жыл бұрын
oh hell ya.. i got those things.. tires on their way, might get it all done tomorrow..
@mrfloorguyz
3 жыл бұрын
So I will add something to this...MAKE SURE YOUR VICE JAWS ARE WIDE ENOUGH!!!!! Otherwise you might only get a small hold and possibly break the rim. Thankfully I figured that out before I got after it to much. and got some wood to go behind the wheel, and in front of the jaws. And yea he slides those on WAY to easy.. I dam near impaled myself with a pry bar hahahaaha
@920003 жыл бұрын
WD-40 WILL DAMAGE THE RUBBER!!! It's a penetrator for metals only! USE SILICONE SPRAY INSTEAD!
@DenisBikeMechanic
3 жыл бұрын
I know that. But the tire thick enough. Wd will soak up with the rubber and stay there. But you won't feel it.
@GarreTTTurncoaT10 ай бұрын
“That’s it”😂 NBD
@dmitriyrusachev20342 жыл бұрын
Can you repeat the same installation on motor wheel? With all those cabels from controller. Then I will 👍this video.
@user-do5hw2lz9e3 жыл бұрын
I have a 10 inches tires on a Pure scotter. I want to change them to a hard ones , since I am getting many punctures. Do you do such a job? where are you located ? how much to change both tires ?
@@DenisBikeMechanic Thanks for the reply ...a bit far for me though ...sorry i thought you are in the UK. by the way I love your videos , and as a recommendation what 10 inch solid tire you would suggest?
@DenisBikeMechanic
3 жыл бұрын
@@user-do5hw2lz9e They all about the same.
@masulubonak92752 жыл бұрын
Nice man ✌️
@DenisBikeMechanic
2 жыл бұрын
Thanks ✌
@hans-georgholthues66554 жыл бұрын
This is the best way to put the solid tire. We did it in less than 3 minutes
@jluisb95382 жыл бұрын
Wao, thank you
@juliantanantac96702 жыл бұрын
Excelente saludos
@cristianespinoza86143 жыл бұрын
Hola como se comporta el neomatico solido en un zero10x?
@keithburt78742 жыл бұрын
Thank You
@oski40762 жыл бұрын
Does This Tire make ur Scooter Go slower?
@RazwoansPhotography11 ай бұрын
Whats is the locking things called?
@cnerolishag949610 ай бұрын
Can you install d4+ nanrobot scooter soild tire?
@davidtien28453 жыл бұрын
Hi Denis, I am wondering how much it will cost if I ship two wheel to you for solid tire replacement. Thank you
@DenisBikeMechanic
3 жыл бұрын
Hello David. $30 per wheel. But the front wheel with the motor most likely does not have a plug to remove. Voltaire cycles, 400 Bloomfield Avenue Verona nj 07044
@zeigermaher
3 жыл бұрын
Denis Grishin Hi, what do you mean? Cant I change front tire on Xiaomi Pro 2?
@DenisBikeMechanic
3 жыл бұрын
@@zeigermaher yes you can, but you can't unplug the motor due to a solid cable.
@idris07863 жыл бұрын
Hi excellent video . 2:30 Sec I cannot get the tyre straighten my tool doesn’t come through to the other side. What should I do?
@DenisBikeMechanic
3 жыл бұрын
Use skin screw driver, drill tire.
@idris0786
3 жыл бұрын
Denis Grishin Ok. I will try Thank you.
@ragnafelix Жыл бұрын
What is the temperatur of the water you use and how long time do you have it in the hot water to make it softer? Greatful for answers.
@DenisBikeMechanic
Жыл бұрын
Actually nowdays I don't heat it up. Unless if it's not freezing, it will stretch.
@ragnafelix
Жыл бұрын
@@DenisBikeMechanic Thanks for the answer
@shylomason31612 жыл бұрын
i can put on solid tyre turboant x7 pro
@TheGaryNinja Жыл бұрын
Hey where did you get the solid tire from? Do you have a link?
@DenisBikeMechanic
Жыл бұрын
Amazon
@AnhTuPhucDerrickHoangCanada Жыл бұрын
Had to make this switch, the tube tires replaced twice in a few months
@Marlucant3 жыл бұрын
Onest 👍👍👍
@cirwo854 жыл бұрын
Is there much difference in speed and range w solid tires?
@DenisBikeMechanic
4 жыл бұрын
hi. Not really it has some more inertia but not sufficient. I didn't feel difference.
@djjumpe4 жыл бұрын
What about the front tire. Wire is tether to it?
@DenisBikeMechanic
4 жыл бұрын
It's a bit complicated. Need to be careful with the wire especially. But principle is same.
@TheKaybjay2
4 жыл бұрын
Denis Grishin - can I come to your location and have my back solid tire installed?
@luckybirdbikes55564 жыл бұрын
Thanks for the nice video! When fixating the tire in the vice it easily scratches the rim, and also metal tire spoons easily damage the rim. Do you have the same experience and any fix for that?
@denisgrishin261
4 жыл бұрын
@Lucky Bird Bikes , our vice is old so the clamps are smooth. You can put some cloth in between. Metal spoons are fine with those rims since thy are thicker than a regular bicycle rims. Nothing happens with the rim and it doesn't get scratched.
@paulopinlac1993 Жыл бұрын
Hi sir is it possible that can put solid tires on pneumatic tires? In short it is possible to convert?
@DenisBikeMechanic
Жыл бұрын
Most pneumatic tires can be replaced with solid ones. Just match the diameter and width of the rim.
@smoll.miniatures6 ай бұрын
Don’t use wd40. You’ll fit it easier but then brake and the tyre will spin on the rim…
@tomsewell24626 ай бұрын
Ok, Ill try it tomorrow. I bet it takes me an hour at least.
@nikanikolic19733 жыл бұрын
Are these tires safe ?cannot be removed while driving?
@DenisBikeMechanic
3 жыл бұрын
Safe. Won't come off.
@joeKisonue Жыл бұрын
Have you ever replaced Unagi tires?
@DenisBikeMechanic
Жыл бұрын
What's so special about them?
@joeKisonue
Жыл бұрын
@DenisBikeMechanic yes or no. No ulterior depth. I have tested out the pliabilty of my tires and given how often I hammer them across light rail crossings, they should pop right off without cutting or heating. Unagi won't sell me new tires. Only gently used. I kinda like them slick. There was a definite vibration from the tread pattern.
@BlackGoldVideosBGV3 жыл бұрын
I did it with microwave and it worked just fine
@lifeisadice67012 жыл бұрын
Hey Denis I have an xtract scooter similar to a kugoo m4 which tyre size is 10×2 50 6.5 and mine is a 10×2 70 6.5 would the kugoo m4 tyre fit mine cause find it difficult to find my size
@DenisBikeMechanic
2 жыл бұрын
Idk. Looks like it may fit.
@lifeisadice6701
2 жыл бұрын
@@DenisBikeMechanic is the 10×2 the rim size and width and the 70-6.5 the tyre height and thickness? Probably silly question but I am clueless
@adamcare3 жыл бұрын
has anyone done this on an apollo explore scooter! they are 10 x 2! i just shelled out 3 flat tires on 45km !
@DenisBikeMechanic
3 жыл бұрын
Idk. Ask seller if there is an option with solid tires. With pneumatic ones- keep pressure high enough otherwise the tubewill be chewed by tire.
@banyolu3 жыл бұрын
Thnx
@a2roland2 жыл бұрын
Thanks.
@nyc_dancer_j2 жыл бұрын
Are you guys still there are you guys still open for business??🤔
@johansolis294 жыл бұрын
How much for that work my friend ?
@denisgrishin261
4 жыл бұрын
$40
@kimball40822 жыл бұрын
How do you do the front wheel
@DenisBikeMechanic
2 жыл бұрын
With a lot of screams, tears and swearing the holy mother.
@vvavie48584 жыл бұрын
It’s always those gotrax gxl back tires
@vvavie4858
4 жыл бұрын
They be poppin
@chriseberth1281
4 жыл бұрын
ikright
@averagejoe4132 жыл бұрын
i need a proper work bench. without that clamp is so much harder to replace it
@LucciDoDaDashАй бұрын
What if i don't have a vice ?
@insanedane76382 жыл бұрын
Did you know the WD40 is acid mate 😅👌 the rubber will by Time disolve at the sides 😒
@fra_nkeygar_36012 жыл бұрын
How to do front wheel its hard whit the sensor cable
@DenisBikeMechanic
2 жыл бұрын
It's a bit harder. You need to clamp it in vice.
@ajgreen868 Жыл бұрын
I didn’t heat the tire and it worked just fine.
@DenisBikeMechanic
Жыл бұрын
In summer time it's okay. But in winter time rubber needs some warm up.
@yuabe2994 жыл бұрын
Hey man please help me i installed yesterday one on my e scooter but now he dont drive faster then normal
@The.Peace.Pixel1
4 жыл бұрын
solid tires are always a bit slower
@denisgrishin261
4 жыл бұрын
@@The.Peace.Pixel1, you're right. they are heavier and require more energy to accelerate.
@The.Peace.Pixel1
4 жыл бұрын
Denis Grishin yeah, I replaced both tires in my scooter with solid tires. The top speed went down by like 10% but the range is what has the decreased the most by like 25%
@MarkDanger777
3 жыл бұрын
Mines came with stock 6.5 inches solid tires, everything is true plus a much more scarier and rougher ride
@airsoul3662 жыл бұрын
What about the front tire?
@DenisBikeMechanic
2 жыл бұрын
Same thing but be careful because of the short wire.
@vvavie48584 жыл бұрын
You didn’t show us how to properly align the tire on the rim
@osirisofthesouth2853
4 жыл бұрын
@2:32 ? Lol
@joeychanco4 жыл бұрын
how about the front tire? thanks
@denisgrishin261
4 жыл бұрын
A bit more difficult because power cord doesn't give much play and you can't unplug the wheel. So need to do it with caution.
Пікірлер: 187
This is the fastest tire installation I've seen so far and I've been searching a lot.
@radamante3231
2 жыл бұрын
Of course he is a mechanics with all tools available
@marsmellow1589
2 жыл бұрын
Put the rim on two pieces of thick wood, heat up the tyre in hot water and with three tyre levers and two persons its quite easy as well.
@kevin_ramirez2529
2 жыл бұрын
@@radamante3231 yea I don’t have a workbench with a vise, wish I did it’ll make it a whole lot easier
Thanks this finally worked for me. For those people who don't have a vice or cable ties like me, I just used by body weight and put my knee on the tire to hold it in place while I used the levers to pull the top part of the tyre over the rim.
I tried getting a local bike shop in Portland to view this video and have my Xiaomi tubeless tire fitted onto my Gotrax XR Ultra rear wheel rim but they were too afraid to commit to this. So I took it upon myself. I gathered some very little supplies from the local hardware store; a 5 gallon bucket, 11 inch zip ties, and a 12 inch bar clamp. The workers at the ACE hardware shop didn't quite know themselves on how to tackle the installation but they agreed that my set-up was sound. Fast forward, I warmed up two pots of water to just under 200 deg F and let the tire soak for 10 minutes. You need just enough water to fully submerge the tire. I had with me two big tire irons from a previous purchase and a can of WD 40 just in case i needed lubricant. Guess what, folks. All it took was ONE zip tie and two of three tire irons I own and the tire went onto the rim in less than one minute. I kid you not, it's fucking doable and I have little to no experience with bike/scooter maintenance (although I have experience as a maintenance worker). 5 Gallon bucket of 200 deg F water (soak for 10 minutes -- THIS IS CRITICAL AND WILL SAVE YOU TIME AND ENERGY) One zip tie (I didn't even need the damn Bar Clamp) Two tire irons (not sure if you can get away with just one) Whole prep and execution done in less than 15 min. Thank you for this video. I've seen countless others and this was by far the most efficient process. I was worried I'd need a table mounted clamp like in this video but I did this on my kitchen floor. For safety reasons, just don't heat the tire in an oven or microwave or have it inside one of your pots. Get a bucket and wear some work gloves while you're at it.
@bob-ny6kn
3 жыл бұрын
I found that placing the tire/rim into a vice and one crowbar (tire iron) was enough. The heated water or soap/cleaner/wd40 was not necessary.
@itsmesezgin
2 жыл бұрын
how can you do it with the wheel where there is no entry with the zip tie, for some the wheel is the front and others its the rear.
This is the best advice on how to install one. Once I saw this, done in 3 minutes, like this man. Well done.
Thanks, locking a point with a strap was the key for me. However, I didn't use WD40 inside for fear the tyre would slip while breaking, just dishwashing soap on the bead. I also used the old tyre as base to work on to keep everything flat.
Just did this last night worked for both front and back tire, only took me 20min each tire, thank you very much!
This is the best tutorial hands down. Others make it look like a nightmare, which is not true at all. The microwave thing and lack of proper tools in other videos will put anyone on a wrong track, where nightmares (and even possible trauma) are to be had.
Definitely the best video. Very effective and short video, no small talk, the best!
This was the only tutorial that helped, thanks!:)
Legend. The trick of chucking it in a vice is the way to go, I didn't have the right tools - but a couple of large flat headed screwdrivers did the trick. Cheers
Thank you for showing the method! It worked well for me. Tips: make sure you heat the tire - microwave is fine, use liquid soap or oil as lubrication - also on your tire levers, think of the process as snapping a big thick rubber band onto the rim. Stretch that tire to get it over the rim and don't be shy, you're not going to break the tire. Next up: I try to do the front tire without a vise.
@codywright8510
10 ай бұрын
I broke the tyre
You legend mate I thought this was impossible took me 5 mins following this 🔥🔥
oh my gosh you are a genius - the idea of using zip ties saved the day, thank you so much!
Awesome video. Couldn’t have done it without you. Thanks
The best video, i tried a lot of others ways and fail. First time i tryed yours, and Done. Thanks from Brazil.
Excellent. Your method worked like a charm. Thanks!
Wow worked great on the rear tire of my Gotrax Elite! Thirty seconds and POP!. Small centering time and done. i do have have to say though. Tried this on my front tire with the hub motor in and had to muscle it the old fashioned way. Not the vice method. Front tire wheel and tire wouldn't stay in the vice for the life of me. Kept popping out. Perhaps removing the hub motor might have made it easier but i doubt it.
Thanks I nearly burst into tears on this job . Great solve!
I struggled using the vise, but found that zip ties worked great and made it pretty easy. I just used soapy water for lubricant and that worked fine.
Worked like a charm!
I learned something, thank you. Though I would put aluminium brackets between the rim and the vice, to avoid damage or bending on the rim.
Extremely helpful video thanks. I had a buddy that was pulling his hair out trying to install the thing.
cool, it is useful to have vice and proper tools for putting on a tire. Since at home you are not going to have vice, ziper method is also fine, and takes only couple minutes.
To the haters in the comment section: 1. I took my daughter's scooter to 5 different bike shops in FL. They all refused to fix it. Being mechanically inclined, I chose to fix it myself. 2. I used silicone grease instead of WD-40. 3. The vise is a must! I tried pressing without it, and it was a nightmare. Thank you for this video!!
Thank you for posting very helpful I pray I never have to remove it .. !!
I like the way how he lubricates
Thank you, this was helpful
This video just saved me a bunch of time, and I appreciate it! It worked like a charm on the rear wheel of my macwheel mx-1. Unfortunately, I had no luck with the front wheel on the motor, as it kept popping out of the vice. Do you have any suggestions on how to do the front wheel?
@DenisBikeMechanic
2 жыл бұрын
Thanks. Probably you need a wider vise.
@itsmesezgin
2 жыл бұрын
@@DenisBikeMechanic a wider vise? Like what? I have the same problem, there is no way to zip tie one of the wheels where there is no entry
Very helpful, thank you!
Good Job...my favourite video...
Oh I have too really thank you, it’s like two out I was trying too feet my new solid tire but I cannot 😅, now I’m boiling water to put my solid tire inside 😂
Hi I've got a kugoo s1 and is it a easy process to change from plastic to rubber and can you show me how to do it please thanks.
BEST VIDEO GOING ON THIS PROCESS!
You made that look so simple Gona get solid tires for my gotrax
@DenisBikeMechanic
2 жыл бұрын
Thanks. Vice is a key point here.
@itsmesezgin
2 жыл бұрын
@@DenisBikeMechanic can you recommand a home-vice? The way you have looks way to big to be in my room.
Bet that vice scratched that rim up nice
Is the Xiaomi Mijia M365 8.5inch compatible with the gotrax gxl v2 tire
I have a Neon Pro Okai scooterr model ES30 and the back tire got badly damaged, so i want to find a decent replacement compatible for it and put 2 new tires to my scooter, im new at this type of stuff and i don't understand very much about tires sizes and comparability The tire says 60/75 - 6.5 (10×2.5) And its hard to find on amazon or ebay and how to look for one that fits And i need my scooter to be able to go to work and back or i would have to walk every day around an 1hour some tes more since i gotta do a lot of heavy lifting at work and my body takes a lot of damage.
Does this fit for a Segway F-30 that has inner tube ? Or can I use a tubeless tire. If yes. What kind can I use.
I need a vice Good job buddy 👍👍
@DenisBikeMechanic
2 жыл бұрын
Thanks!
Hover 1 Alpha electric scooter Tire and inner tube ??? Solid tire ??? I can't able to find it anywhere any ideas please let me know
Mine came with solid rubber tires (HiBoy S2 Pro) and they are rock hard with hardly any flex at all. I'd like to replace them with honeycomb tires but they look like a pain to remove 😩.
hi mister, can i buy them red in 8p and adapt them to my xprit 10p scooter?
О, наш человек! Наш человек всегда профессионал! Спасибо за видео ;-)
@DenisBikeMechanic
3 жыл бұрын
Спасибо за коммент!
@MrMaybe89
Жыл бұрын
@@DenisBikeMechanic Dobrii denj. Estj vopros. Etji koleso bez vozduha ne ochen horoshie? Govorjat shto tjazhelo katatsa.
@DenisBikeMechanic
Жыл бұрын
@@MrMaybe89 зимой дубеют, летом норм. В целом solid tires лучше чем постоянно латать надувные.
@MrMaybe89
Жыл бұрын
@@DenisBikeMechanic Spasibo za otvet. Nu zimoi ja vobsje nje jedu. No mnje znakomii govoril shto s Solid Tyres ochen tjazhelo, koleso kak kamnji. Tjipa bjotsa ochen kogda jedish.
@DenisBikeMechanic
Жыл бұрын
Поставь русскую Клаву. Глаза сломать можно ;) На мой скутер я бы поставил solid tires и не парился бы. Они жёстче но практичнее.
It's looks so easy. I'm planning to get a solid tire scooter.
may I know how this tire perform ? is that better ? I wondering should I put on my mten3 ...
@DenisBikeMechanic
2 жыл бұрын
It's about the same. I don't see much difference when ride it.
I don't use E scooters myself but done a couple of scooters for my work colleagues the way I done it was to use a vice a weak solution of washing up liquid a utility bar didn't heat the tires still had them on in seconds
Nice, will try this
@jojjan93
3 жыл бұрын
@OG Loc i won't. I threw the scooter away
How often will live that solid tire? 1 year?
Thank you.
For me it's just easier to pay a bike shop and never use air filled tires again.
how can you do it with the wheel where there is no entry with the zip tie, for some the wheel is the front and others its the rear.
solid tyres are hell for city streets such a rough ride
@adamcare
3 жыл бұрын
no air tires are, because they go flat!
Are there benefits to this over a inner tube tire
@albertgutierrez7036
Жыл бұрын
With a solid tire you’ll never need to add any air ever just grab and go not really recommend this for stronger scooters these wheels work better on entry to mid level escooters.
oh hell ya.. i got those things.. tires on their way, might get it all done tomorrow..
@mrfloorguyz
3 жыл бұрын
So I will add something to this...MAKE SURE YOUR VICE JAWS ARE WIDE ENOUGH!!!!! Otherwise you might only get a small hold and possibly break the rim. Thankfully I figured that out before I got after it to much. and got some wood to go behind the wheel, and in front of the jaws. And yea he slides those on WAY to easy.. I dam near impaled myself with a pry bar hahahaaha
WD-40 WILL DAMAGE THE RUBBER!!! It's a penetrator for metals only! USE SILICONE SPRAY INSTEAD!
@DenisBikeMechanic
3 жыл бұрын
I know that. But the tire thick enough. Wd will soak up with the rubber and stay there. But you won't feel it.
“That’s it”😂 NBD
Can you repeat the same installation on motor wheel? With all those cabels from controller. Then I will 👍this video.
I have a 10 inches tires on a Pure scotter. I want to change them to a hard ones , since I am getting many punctures. Do you do such a job? where are you located ? how much to change both tires ?
@DenisBikeMechanic
3 жыл бұрын
Voltaire cycles of Verona, NJ. 400 Bloomfield ave Verona nj. $80 labor.
@user-do5hw2lz9e
3 жыл бұрын
@@DenisBikeMechanic Thanks for the reply ...a bit far for me though ...sorry i thought you are in the UK. by the way I love your videos , and as a recommendation what 10 inch solid tire you would suggest?
@DenisBikeMechanic
3 жыл бұрын
@@user-do5hw2lz9e They all about the same.
Nice man ✌️
@DenisBikeMechanic
2 жыл бұрын
Thanks ✌
This is the best way to put the solid tire. We did it in less than 3 minutes
Wao, thank you
Excelente saludos
Hola como se comporta el neomatico solido en un zero10x?
Thank You
Does This Tire make ur Scooter Go slower?
Whats is the locking things called?
Can you install d4+ nanrobot scooter soild tire?
Hi Denis, I am wondering how much it will cost if I ship two wheel to you for solid tire replacement. Thank you
@DenisBikeMechanic
3 жыл бұрын
Hello David. $30 per wheel. But the front wheel with the motor most likely does not have a plug to remove. Voltaire cycles, 400 Bloomfield Avenue Verona nj 07044
@zeigermaher
3 жыл бұрын
Denis Grishin Hi, what do you mean? Cant I change front tire on Xiaomi Pro 2?
@DenisBikeMechanic
3 жыл бұрын
@@zeigermaher yes you can, but you can't unplug the motor due to a solid cable.
Hi excellent video . 2:30 Sec I cannot get the tyre straighten my tool doesn’t come through to the other side. What should I do?
@DenisBikeMechanic
3 жыл бұрын
Use skin screw driver, drill tire.
@idris0786
3 жыл бұрын
Denis Grishin Ok. I will try Thank you.
What is the temperatur of the water you use and how long time do you have it in the hot water to make it softer? Greatful for answers.
@DenisBikeMechanic
Жыл бұрын
Actually nowdays I don't heat it up. Unless if it's not freezing, it will stretch.
@ragnafelix
Жыл бұрын
@@DenisBikeMechanic Thanks for the answer
i can put on solid tyre turboant x7 pro
Hey where did you get the solid tire from? Do you have a link?
@DenisBikeMechanic
Жыл бұрын
Amazon
Had to make this switch, the tube tires replaced twice in a few months
Onest 👍👍👍
Is there much difference in speed and range w solid tires?
@DenisBikeMechanic
4 жыл бұрын
hi. Not really it has some more inertia but not sufficient. I didn't feel difference.
What about the front tire. Wire is tether to it?
@DenisBikeMechanic
4 жыл бұрын
It's a bit complicated. Need to be careful with the wire especially. But principle is same.
@TheKaybjay2
4 жыл бұрын
Denis Grishin - can I come to your location and have my back solid tire installed?
Thanks for the nice video! When fixating the tire in the vice it easily scratches the rim, and also metal tire spoons easily damage the rim. Do you have the same experience and any fix for that?
@denisgrishin261
4 жыл бұрын
@Lucky Bird Bikes , our vice is old so the clamps are smooth. You can put some cloth in between. Metal spoons are fine with those rims since thy are thicker than a regular bicycle rims. Nothing happens with the rim and it doesn't get scratched.
Hi sir is it possible that can put solid tires on pneumatic tires? In short it is possible to convert?
@DenisBikeMechanic
Жыл бұрын
Most pneumatic tires can be replaced with solid ones. Just match the diameter and width of the rim.
Don’t use wd40. You’ll fit it easier but then brake and the tyre will spin on the rim…
Ok, Ill try it tomorrow. I bet it takes me an hour at least.
Are these tires safe ?cannot be removed while driving?
@DenisBikeMechanic
3 жыл бұрын
Safe. Won't come off.
Have you ever replaced Unagi tires?
@DenisBikeMechanic
Жыл бұрын
What's so special about them?
@joeKisonue
Жыл бұрын
@DenisBikeMechanic yes or no. No ulterior depth. I have tested out the pliabilty of my tires and given how often I hammer them across light rail crossings, they should pop right off without cutting or heating. Unagi won't sell me new tires. Only gently used. I kinda like them slick. There was a definite vibration from the tread pattern.
I did it with microwave and it worked just fine
Hey Denis I have an xtract scooter similar to a kugoo m4 which tyre size is 10×2 50 6.5 and mine is a 10×2 70 6.5 would the kugoo m4 tyre fit mine cause find it difficult to find my size
@DenisBikeMechanic
2 жыл бұрын
Idk. Looks like it may fit.
@lifeisadice6701
2 жыл бұрын
@@DenisBikeMechanic is the 10×2 the rim size and width and the 70-6.5 the tyre height and thickness? Probably silly question but I am clueless
has anyone done this on an apollo explore scooter! they are 10 x 2! i just shelled out 3 flat tires on 45km !
@DenisBikeMechanic
3 жыл бұрын
Idk. Ask seller if there is an option with solid tires. With pneumatic ones- keep pressure high enough otherwise the tubewill be chewed by tire.
Thnx
Thanks.
Are you guys still there are you guys still open for business??🤔
How much for that work my friend ?
@denisgrishin261
4 жыл бұрын
$40
How do you do the front wheel
@DenisBikeMechanic
2 жыл бұрын
With a lot of screams, tears and swearing the holy mother.
It’s always those gotrax gxl back tires
@vvavie4858
4 жыл бұрын
They be poppin
@chriseberth1281
4 жыл бұрын
ikright
i need a proper work bench. without that clamp is so much harder to replace it
What if i don't have a vice ?
Did you know the WD40 is acid mate 😅👌 the rubber will by Time disolve at the sides 😒
How to do front wheel its hard whit the sensor cable
@DenisBikeMechanic
2 жыл бұрын
It's a bit harder. You need to clamp it in vice.
I didn’t heat the tire and it worked just fine.
@DenisBikeMechanic
Жыл бұрын
In summer time it's okay. But in winter time rubber needs some warm up.
Hey man please help me i installed yesterday one on my e scooter but now he dont drive faster then normal
@The.Peace.Pixel1
4 жыл бұрын
solid tires are always a bit slower
@denisgrishin261
4 жыл бұрын
@@The.Peace.Pixel1, you're right. they are heavier and require more energy to accelerate.
@The.Peace.Pixel1
4 жыл бұрын
Denis Grishin yeah, I replaced both tires in my scooter with solid tires. The top speed went down by like 10% but the range is what has the decreased the most by like 25%
@MarkDanger777
3 жыл бұрын
Mines came with stock 6.5 inches solid tires, everything is true plus a much more scarier and rougher ride
What about the front tire?
@DenisBikeMechanic
2 жыл бұрын
Same thing but be careful because of the short wire.
You didn’t show us how to properly align the tire on the rim
@osirisofthesouth2853
4 жыл бұрын
@2:32 ? Lol
how about the front tire? thanks
@denisgrishin261
4 жыл бұрын
A bit more difficult because power cord doesn't give much play and you can't unplug the wheel. So need to do it with caution.