Install a Milliamp Meter / mA Meter on a CO2 Laser Cutter
Тәжірибелік нұсқаулар және стиль
Today we're going to be looking at installing an mA Meter on a 50w laser cutter.
Having a milliamp meter installed on your CO2 laser cutter will let you better monitor the power output of your laser cutting machine.
My CO2 laser engraver is similar to the popular k40 laser cutter and other Chinese laser engravers, so the install process should be similar for other machines, like an 80w laser cutter.
*****Check out other videos on laser engraving*****
Chinese CO2 Laser Engraver / 50w Laser Cutter Guide Ep. 1: • Chinese CO2 Laser Engr...
CO2 Laser Engraver Air Assist & Exhaust. Beginner Series Ep. 2 : • CO2 Laser Engraver Air...
CO2 Laser Engraver Water Cooling & Laser Chillers. Beginner Series Ep. 3: • CO2 Laser Engraver Wat...
CO2 Laser Software / K40 Whisperer & Inkscape / Beginner Series Ep. 4: • CO2 Laser Software / K...
CO2 Laser Alignment and How to Clean Laser Lens and Mirrors / Beginner Series Ep. 5: • CO2 Laser Alignment an...
CO2 Laser Focus / Focusing Laser Lens Ramp Test - Laser Engraver Beginner Series Ep. 6: • CO2 Laser Focus / Focu...
*********************
#MilliampMeter #CO2LaserCutter #mAMeter
Download the Milliamp Meter console laser cut files:
bit.ly/3gAbPKV
* Official Website maketechcreate...
* Follow on Instagram - / maketechcreate
Пікірлер: 21
Sounds like a much better way of monitoring machine power output
Such a most innovative design did you use! I saw many laser owners make a big hole on the laser body that it's not so lovely. If for any reason, they don't want to use it anymore or want to replace it with a new meter, they make the machine defective and look ugly. Thanks for sharing your effective experience with us. 💯👌👋
@MakeTechCreate
2 жыл бұрын
You are welcome. Thanks for watching!
Thanks for the good video. What else I would like to see is how you installed your temperature meter.
@MakeTechCreate
Жыл бұрын
The temp meter came with the machine. The temperature probe is literally just taped to the laser tube.
Great job. Well done. 👍🏻
@MakeTechCreate
2 жыл бұрын
Thank you 😊
Thank you. Most helpful
@MakeTechCreate
2 жыл бұрын
You're welcome 😊
Do you have a video covering the controller upgrade? I don't see one in your feed.
Sir can u send laser corel software for my co2 laser cutting mac
Hi. Are you sure it’s not an AC meter you have installed? Looking at the symbol it sure looks like it’s meant for AC
@MakeTechCreate
2 жыл бұрын
Crap ... your right ... I ordered a DC meter but after checking, that's an AC symbol ... regardless, it's working for what I need. Changing it will be simple enough ... I guess I should probably wear my glasses more 😆
@nikdonic
2 жыл бұрын
@@MakeTechCreate it may display different walues than DC meter because there is pulsed DC so I wonder how accurate is measurement with DC meter
How did you get an extension display for your water temp?
@MakeTechCreate
2 жыл бұрын
It's just a touch tempature display that came with the laser. There was more then enough with to extened it to the new display.
Cant see where or how you wired positive
@MakeTechCreate
18 күн бұрын
The negative wire from your laser tube goes to the positive terminal on the gauge.
What gauge wire did you use for the extension wires?
@spluesh
2 жыл бұрын
roll said 16 gauge.
Pleas sent me design and easy software for designing