Impala Gets New Floors and Tubs - MuscleCar S3, E10
Автокөліктер мен көлік құралдары
Rick and Brent tackle the metalwork on the '61 Impala, including floorpans and tubs. Rick takes the frame to get powder-coated. Flashback to the heyday of the Corvette in a '67 Sting Ray.
Follow POWERNATION Everywhere:
www.powernation...
/ powernationtv
/ powernationtv
PARTS USED IN THIS EPISODE:
Borgeson: Increased ratio manual gearbox, U-joints and steering shaft.
Loctite: Loctite sealers, thread locking compounds, gasket making compounds.
Powder-X: Black powder coated frame section and media blasting of body parts and frame parts.
Stainless Steel Brakes: 13 inch front rotors, four piston calipers, red powdercoating, chrome booster and billet master cylinder.
Stainless Steel Brakes: Rear disc brake package for LB Torino ends, powdercoated red.
YearOne: RH floor brace, LH and RH full floor pan, RH trunk floor, LH floor brace, RH floor brace, trunk floor center section, RH floor box brace, LH floor box brace, RH outer trunk extension floor panel, LH and RH toe board, shift tunnel plate seal, shift tunnel plate, trunk floor brace, fuel tank brace, upper rear seat floor brace, upper trunk floor, upper trunk floor brace, LH outer trunk floor extension panel, RH under seat floor brace, LH under seat floor brace, LH under seat pan, RH under seat brac
Пікірлер: 143
No professional powder coater would have done that. I blast every frame I do to white metal , outgas, prime and topcoat. And by the time they are done assembling that gloss black will look like semi gloss black.
Lincoln stickers on the hood but Miller gets the work done! The Power of Blue!!!!
I really like the episodes when you guys go into details with body work and welding tips. Teaching while building is a plus.
I seen this car at a show a few years ago. They took a lot of short cuts and the rear wheels rubbed the quarters . I could go on and on.
61 impalas are gorgeous!!!!! Especially bubble tops!! 🤤🤤🤤😍😍😍
@carlmiddletonjr5856
3 жыл бұрын
I had 2 red an a blue an white. Love them.
This was a great episode, with lots of detail on the metal replacement. You guys deserve much credit as that's a lot of work.
@Marcus_Woodard
4 жыл бұрын
Powder coat over rust?
@timyowell4278
4 жыл бұрын
I've seen this car. They left a lot of rust in it. They welded panels over rust in places. The car was not done correctly at all.
I'm loving this build.
I'm glad i don't have to watch this on TV, commercial breaks every 5 minutes would drive me nuts!
2:26 - Great job on the rust removal - Ready to rock
@Diddy_Doodat
4 жыл бұрын
It's called surface rust 🤦🏾♂️
@kene6838
4 жыл бұрын
Diddy Doodat And that’s how rust starts, on the surface dude. Do you work there and are trying to justify shoddy work?
Explain how you can powdercoat over rust and why would you want to if it creates peeling down the road ?
@Diddy_Doodat
4 жыл бұрын
You clearly didn't see them removing the rust before they powder coated it. Wow, you people don't pay attention
@jaydaytoday3548
4 жыл бұрын
@@Diddy_Doodat 2:26
@colbysmith1398
4 жыл бұрын
The frame still had surface rust when they started coated. Clearly seen in the video. The frame really needed media blasting.
@richardhopkins3348
4 жыл бұрын
@Gman 2060 9
@JonDraeger
4 жыл бұрын
Why would you powdercoat anything? It is only a matter of time before chipping and peeling happens and when it does, you can't do a damn thing about it but start completely over again.
Welcome to Half Ass Auto, staring Dur and Duh.
Good work man
At 2:26 looks like a nice cracked weld where he is attaching the ground. Great job love the vids!
maybe I missed it but, it looked like they powder coated over rust to me
@kennash5719
3 жыл бұрын
I thought the same, wait for a rainy day to take it to the powder coating place? POR 15 might be a better choice
@BryanM362
3 жыл бұрын
Thought the same, but maybe the rust removal got edited out....??
I've cut it 3 times and it's still to short.
Cheesey show
Just found this channel, this is everything motor trend and roadkill should have become.
Powder coat on rust? My local guy wouldn't touch that without sandblasting the metal clean. These guys can afford to do it better.
@Diddy_Doodat
4 жыл бұрын
First of all it was surface rust. Secondly, did you not see them remove the rust in this very video? 🤦🏾♂️
@colen32147
4 жыл бұрын
Lol thats not removing rust. Removing rust means zero left. That surface rust needs to be blasted to remove it from metal pores or it needs to be chemically neutralized
@geneva760
4 жыл бұрын
2:26 - HMMMMMMMMMM - that orange stuff must be a special adhesion promoter called Fe2O3 epoxy rust zapper - TREMENDOUS - GREAT job stuff (I think that is its full Trademarked name).
@kene6838
4 жыл бұрын
Diddy Doodat That’s a lousy job of prep before powder, don’t stick up for work that is half ass.
@badad0166
4 жыл бұрын
Surface rust (flash) will get encapsulated. But I get your OCD and agree with diligence.
The chassis is pitted and rusty, why are you power coating it that way?
@The.Real.Timmii
4 жыл бұрын
Art Morrison frame is wtg
@unclefreddieDied
4 жыл бұрын
ha i recognize you from the entertainah's channel... go big blue!
outstanding!!! imho the 67 c2 sting ray was the best looking vette ever, and the drop top was the holy grail @ 10:39
I was going to show this to a friend doing his first total restoration but after seeing those undressed beads and all that rust you power coated over I would never show this to anyone and will look at your feature builds with a healthy dose of skepticism...
@chestermcflugelhorn5934
4 жыл бұрын
Just get your friend to read the youtube comment sections i'm sure he'll find all the info he needs 🤣
@BryanM362
3 жыл бұрын
I agree, didn't understand why they would powder coat over the flash rust!
@kalijasin
2 жыл бұрын
@@BryanM362 Didn't sand off the rust on frame or media blast the frame. 🤦♀️
I think these guys are more actors that car guys !!!
@jackkrinkov9273
3 жыл бұрын
They are more hacks than anything else
@AutoYoung
Ай бұрын
You obviously don’t know a damn thing…
The powder coat brothas...
A better way to attach that bracing to the underframe (Super Labor Intensive) is to do it Aircraft-Style, that is, precisely drilled .250" holes and Military-Grade Blind fasteners (MS90354S08-xx). Smeared with plenty of AC-730 Sealant.
I love how Rick doesn’t use gloves or a jacket when he’s welding or plasma cutting
Those 4 doors look good fixed up there was some young guy that own a white one like that lowerd with chrome wheels, that was the first time I took interest in 4 doors can be cool to if it's done right. My neighbor owned a 1949 Desoto 4 door in the early 80's we cruised all over San Francisco San Jose Sacramento bay area in that old classic 4 door bomb oh and it had a ship horn in it that would scare the heck out of pedestrians
Anyone know what happened to the final episodes of this built? I can’t find them.
Those old Biscayne / impala wanna-bes are cool.
The extensive rust on this project would of been a bit over whelming for myself,it was deep.
No offense but those plating welds looked pretty bad. I'm sure they'll hold but yikes guys!
@BUTCH0120
3 жыл бұрын
Like Stevey Wonder welding with his feet.
12:07 That 0-60 is the same as a modern smart ForTwo LOL
The chassis is placed in the oven naked to de-gass the steel , not to dry it out !! If you don't do this , bubbles appear in your coating , no one should powder coat over rust , bad practice
I love impalas
Bruh the way he said impahla lol
I have never seen powder coating done this way. Most everyone I have seen smokes the parts by sandblasting and then coat.
The Corvette wasn't the first Fiberglass American Sports Car, Kaiser Willys offered the Kaiser Darren 161 before the Corvette was introduced, the Darren was all fiberglass and introduced in 1952. Only 485 were build but it was still first. The Corvettes first year saw very low production figures as well
Was that oil smoke coming from the vett lol. Only good vett 55-56 steel body
Nice
Can you tell me anything about using old sheet steel from a underground fuel tank its thick can it be treated in any form to use as patch panels or floor pans
Had this guy that had $$$ and thought he was fast with his 67 tri power 427 vette.. My buddy had a 66 tri power GTO that had visited Royal pontiac and had a 421 loaded under the hood with all the treatments. The Vet guy challenged him.. and Lost big time. That was the 500 dollar first run. He said he would be back in a couple of hours. We sat at A&W drinking Rootbeer floats. He showed up having super tuned his Vette at the Speed shop. Well he was only a car legenth behind that run. He wanted another chance. That round cost him 1k in money. So he showed up at like 3am for one more shot.. Well He lost by a fender... He was stoked but coughed up the 2k and drove off.. We ended up pushing my buddys GTO into a farm turn in for a tractor and getting a tow home.. See Larry blew up his Munci in 3rd gear and actually still coasted in beating the vette....... Well At least we had some $$$ and the money go buy one of them M22 rock crushers for the GTO
That's not how they prepared my frame for powder coating.
I was expecting higher quality work. I would be very upset if someone did such rough work on one of my cars.
@kalijasin
2 жыл бұрын
Poor workmanship. Powder coated over rust. Didn't sand off the rust on frame or media blast the frame. Frame was not checked for square and level. Many rough spots on frame that didn't get ground down and smoothed out. No inner support for frame. Very bad Tac welds on body sheet metal. Its a clumpy mess. One of the cross members/bracing was pieced together. Should of been one solid piece.
This video is from like 2009 and the car was finished in like 2011.
@aidanridings8452
4 жыл бұрын
I Know right
@unclefreddieDied
4 жыл бұрын
my favorite parts are when they're working on a car... then they go to different segment, and you can see the finished car in the background
Power coating Sucks! I had rims done for a Vega a few years back. I sand blasted them clean. Sent them to my local powercoater. Mounted tires on them and used the car. It was not long before I got stone chips and started rusting under the powercoat. They bubbled rust under the powercoat. Best to use a good wet primer and top coat. I personally will never do it again. Powercoat is baked at 400 F but can chip fast too.
Inside frame rails...rust.
Tub
I'm surprised it didn't fold in half with no bracing...
0:17 Don't stay in fourth for to long!
Will a 64' Impala floorpan fit a 64' Buick Electra?
@MrDmorgan52
3 жыл бұрын
Think so. Both are B bodies
What happened to the LeMans? Is there a video dedicated to it's launch or is it just those clips added to that one video that shows it as a cameo?
Still the best build series regarding bodywork they ever did.
Saw a youtube of a shop that got redsled. Engine was always too rich, headlights held in with ziptie, doors don't lock. Lots of issues
@jack002tuber
4 жыл бұрын
@@TheAggromonster kzread.info/dash/bejne/o4mTyKOpeMjKlaQ.html
@jack002tuber
4 жыл бұрын
Type redsled in YT search and it is the first link
maybe you should powder coat the body too! 🤔
Why you have sandblaster, if you paint it on rust after rain?????
@eskieman3948
Жыл бұрын
What?
@user-pu6ob7xn3j
Жыл бұрын
@@eskieman3948 sorry i am from Russia my english is bad
Most of the classic terms for auto's were derived from horse drawn carriages.
This guys going to the hospital not for coronavirus but for metal fragments dust in their lungs
At the end look like you were watching him weld with no eye protection? Not good for teaching on a video and metal with no eye protection.
what was the removable pins to hold the panels in place for welding called?
@brucetkane
3 жыл бұрын
Found it, Cleco Pins...
Dream job lol
Guys I need the full episode of this project please 🙏
why did you not blast it after you pre heat it, you powdercoat the job on rust, im a powder coater, that was not a good practice, it will soon chip off
In stead of putting those stupid flames underneath you should have spent your time practicing your welding and grinding that chassis was horrible why would you send that to be powder coated just horrific
1st for red sled ayeee
Another KZread er' told me disk breaks are for cowards!
Alguém Brasil?
Busted. IPhone dash holder @ 12:27
@karlsmith2570
4 жыл бұрын
That's the rearview mirror
Чет халтура при подготовке, перед покраской рамы. Да и проще отпескоструить было наверное перед покраской.
I didnt get episode 11 !!😔 Pls help anyone
Drum brakes are weak? Why were they used on semi trucks then?
@bmstylee
3 жыл бұрын
Big difference between a big rig and a 4000lb car.
Look, when a car has as much rust damage as that POS... You throw it away! And there was absolutely no reason to reinforce the rear part of the frame as much as these clowns did... You act like your putting in a Pro Mod engine, Geeeez...
is joe the son of bill from booton, nj
AllI see is total rust powder coated over, junk!
That's not an Impala.
@johnny_6T8
4 жыл бұрын
it is to them..lol Seeing it as a "post" car is why i clicked to watch. Cool car nonetheless.
@rsstrazz6261
4 жыл бұрын
Yes it is - 1961 was the only year an Impala 2 door sedan was available as well as the more popular hardtop. The 6 tailights, wider side moulding trim/mounting holes, dash & steering wheel confirm it's an Impala. On KZread there's also a video of a '61 Super Sport 2 dr.sedan 348/350 Fawn Beige & Almond Beige. "Big John" plays in the background.
at 2:09 minute i see rust on the frame. and he sprayed the color on the frame !! ????
@arniemeyer7774
3 жыл бұрын
we clean parts with sandblasting or dry ice blasting for a clean ground !
It's not an 61 Impala that's a 61 Bel Air
Powder coat over rust, chuck marks everywhere you drill? Someone send them back to school on how to work with metal properly.
@benjaminsmith9534
4 жыл бұрын
TheAggromonster that had like a quarter inch gap!
Goddam !! That's a lot of work. The cars a Swiss cheese of rust, but, it'll come good. Some commenters think they are building the Pyramids, but it just a car, made of metal, it'll rust again in another 60 years.
Art Morrison frame way better
Literally still covered in rust...it's not going to last. Powder coating is overrated, 2 part epoxy coating would've been more appropriate.
@Dixler683
4 жыл бұрын
sean5comet powder coating is crap. Before I could finish the car my frame was bubbling all over . Done by a professional shop, actually paid them money to f -up my frame. Next frame was dipped to de - rust and E-coated, then por-15. Still looks great and that was 2002.
ok can't find e11 .... no need to subscribe
Looked like a crappy powder job. When done right it should be completely smooth , this looked like a preschooler painted it with water paint. A scuffing with a da is not rust removal and 5 minutes in oven does not dry it out completely, can you cook fries completely in 5 minutes in oven?
Sorry, but no... the frame prep was ... not so much. Grind that frame smooth, welds, and ruff spots before even thinking about taking it to the powdercoater. Powder coating over surface rust.. no.. powder coating without sand blasting? No.. But I am not a pro like these guys..
There is no reason to fix a car like that un less it for a costumer and he is paid if a lot
@TomsChevelle
4 жыл бұрын
What?
Don't buy a car from these guys. Your frame will be rusted out. Powder coating a rusty frame. Shame shame.
qq
What was that? Cut twice measure once Or measure once and cut twice. I don't know u car pepe's come with the darnedest things. You heard the pro's Leroy cut it again. I measured once upon a time. Hehehehe. Y'all make more vidio's K ? Awer car might look that good if we had some fancy unyforms like them little fellers. Hehehe. Dang that's some good grinder smoke. Pass that grinder over here leroy. Hehehe
Those wheels are gross
First
@dannyfelix6440
4 жыл бұрын
Total waste of money and time no integrity how in the heck are you powder coating over rust that Frame is going to pill big time The powder coating guy said they were the leaders in powder coating buissnes. To powder coat over rust is One of the biggest no no's in the business you might as well have powder coated over oil.
@denniskirk4055
4 жыл бұрын
Touchy Feely Joe doesn't have a chance in November.
@johnny_6T8
4 жыл бұрын
@@denniskirk4055 I don't know about that. After all, he handled Corn-Pop.. "Corn-Pop was a bad dude"...lol
its one of the ugliest Chevy's ever